Thesis (Ph.D.)--University of Wollongong, 2008. / Typescript. Includes bibliographical references.

Membrane technology can be utilised for the high purification and desalination of water. However membrane filtration processes are commonly impeded by membrane fouling, which can lead to flux decline and an overall reduction in separation efficiency within the process. Therefore the aim of this research study was a comprehensive investigation of the issue of biofouling on industrial RO membranes through molecular biology techniques, characterisation of surface charge of foulant bacteria and RO membrane surface and AFM imaging and force measurements on clean and fouled membranes for the determination of adhesion force and micromechanical properties. The laboratories within Gwangju Institute of Science and Technology, South Korea and Swansea University, Wales were equipped for the scope of this research work. Research focused on the extraction of microbial DNA obtained from fouling layers on the surface of Reverse Osmosis Membranes obtained from the Fujairah Water and Power Plant, UAE. The use of the culture independent method of the molecular technique based on the 16S rDNA sequence and constructed gene libraries, was then used to determine the bacterial species that caused significant fouling on the RO membrane. Four bacterial species isolated from the fouling layer from the RO membrane were characterised in terms of electrophoretic mobility and zeta potential to determine the cell surface charge within various industrial relevant environments for the elucidation of cell adhesion mechanisms to the membrane surface. AFM images of virgin and fouled membranes were obtained and analysed to reveal the roughness of the surface which could influence fouling and the surface charge of the membranes were measured through the method of streaming potential at various industrial relevant environments to further elucidate the mechanisms of cell adhesion to the membrane surface. Force measurements were performed to reveal the adhesion force and elasticity values of virgin, process fouled and purposely fouled with the four bacterial isolates, to determine process behaviour in various environmental conditions. Through this research and future work, it is hoped that a rational strategy for economic and effective cleaning processes will be developed which will maintain efficient membrane operation and prolong membrane life, thus enabling the reduction of operating costs of such processes.

abstract: Reverse osmosis (RO) membranes are considered the most effective treatment to remove salt from water. Specifically, thin film composite (TFC) membranes are considered the gold standard for RO. Despite TFC membranes good performance, there are drawbacks to consider including: permeability-selectivity tradeoff, chlorine damage, and biofouling potential. In order to counter these drawbacks, polyamide matrixes were embedded with various nanomaterials called mixed matrix membranes (MMMs) or thin film nanocomposites (TFNs). This research investigates the use of graphene oxide (GO) and reduced graphene oxide (RGO) into the polyamide matrix of a TFC membrane. GO and RGO have the potential to alter the permeability-selectivity trade off by offering nanochannels for water molecules to sieve through, protect polyamide from trace amounts of chlorine, as well as increase the hydrophilicity of the membrane thereby reducing biofouling potential. This project focuses on the impacts of GO on the permeability selectivity tradeoff. The hypothesis of this work is that the permeability and selectivity of GO can be tuned by controlling the oxidation level of the material. To test this hypothesis, a range of GO materials were produced in the lab using different graphite oxidation methods. The synthesized GOs were characterized by X-ray diffraction and X-ray photoelectron microscopy to show that the spacing is a function of the GO oxygen content. From these materials, two were selected due to their optimal sheet spacing between 3.4 and 7 angstroms and embedded into desalination MMM. This work reveals that the water permeability coefficient of MMM embedded with GO and RGO increased significantly; however, that the salt permeability coefficient of the membrane also increased. Future research directions are proposed to overcome this limitation. / Dissertation/Thesis / Masters Thesis Civil and Environmental Engineering 2017

L'osmose inverse (OI) est actuellement le procédé le plus utilisé mondialement pour le dessalement des eaux saumâtres et de l’eau de mer. Cette thèse s'est intéressée à la simulation moléculaire de membranes d'OI afin d'améliorer la compréhension des propriétés structurales, dynamiques et de transport de l'eau et d'ions à l'intérieur de ces matériaux. La membrane d'OI étudiée dans ce travail est une membrane de polyamide aromatique, matériau le plus utilisé actuellement en OI. Dans la première partie de ce travail, une méthodologie a été développée pour construire un modèle atomique en trois dimensions d'une membrane polyamide fortement réticulé. Des simulations de dynamique moléculaire à l’équilibre (EMD) et hors-équilibre (NEMD) ont été réalisées pour étudier le comportement de l'eau et des ions Na+ et Cl- à travers la membrane. Les simulations EMD ont montré que les caractéristiques structurales de la membrane modèle étaient en bon accord avec celles d'une membrane typique d'OI. Les propriétés dynamiques et diélectriques de l'eau confinée dans la membrane ont également été étudiées et il a été montré que celles-ci étaient fortement modifiées par rapport à une phase volumique. Deux types de techniques NEMD ont été utilisés pour étudier le transport baromembranaire à travers la membrane modèle. La perméabilité à l'eau pure a été trouvée en très bon accord avec les données expérimentales rapportées dans la littérature et les deux méthodes NEMD ont révélé une très forte rétention saline, confirmant ainsi la pertinence du modèle de membrane d'OI développé dans ce travail. / Reverse osmosis (RO) is currently the leading process used worldwide for both brackish and seawater desalination. This thesis focuses on the molecular simulation of RO membranes in order to improve the understanding of structure, dynamics and transport of water and ions inside these materials. The RO membrane studied in this work is a typical polyamide RO membrane. In the first step of this work, a methodology for building a fully atomic and three-dimensional model of a highly cross-linked polyamide membrane was developed. Both equilibrium molecular dynamics (EMD) and non-equilibrium molecular dynamics (NEMD) simulations were further performed to investigate the behavior of water and ions (Na+ and Cl-) through the membrane. EMD simulations showed that the structural characteristics of the model polyamide membrane were in good agreement with those of a typical RO membrane. The dynamics and dielectric properties of water confined in the RO membrane were also studied and have shown to be dramatically modified with respect to the bulk phase. Two types of NEMD techniques were employed to investigate pressure-driven transport through the model membrane. Pure water permeability was found to be in very good agreement with experimental data reported in the literature for similar membrane materials and both NEMD methods highlighted very high salt rejection properties, thus confirming the relevance of the model membrane developed in this work.

The use of Reverse osmosis (RO) membranes have been significantly increasing in water desalination, and the main operational obstacle in RO desalination plants is membrane fouling. Among other solutes, dissolved biopolymers, such as polysaccharides can lead to severe membrane fouling especially with the addition of calcium ions because of the complexation formation between the surface of membrane and foulants materials. However, this complexation can also take place in the feed bulk, resulting in foulants aggregates formation. Although there are some physical techniques that can maintain the membrane performance without reducing its lifetime, only chemical cleanings are still commonly used in RO plants. In this study, a novel cleaning method is proposed to restore the membrane performance by removing the deposited foulants without reducing the membrane lifetime. The cleaning method is based on using water saturated with dissolved CO2 gas, and its principle is based on producing spontaneous CO2 bubbles due to local pressure difference leading to nucleation of bubbles throughout the membrane surface, especially at nucleation sites, which improve the cleaning efficiency. Alginic acid sodium salt was used as a model of polysaccharides foulants in presence of different concentrations of NaCl and calcium ions aiming to enhance membrane fouling, and then CO2 cleaning solution efficiency, in terms flux recovery (FR), was tested under different operating conditions and compared to other cleaning methods. Average FR of 20%±3, 25%±3 and 80%±3 for MilliQ water, a cleaning solution at pH4, and CO2 solution at 6 bar, 0.17 m/s, and 23 ̊C ±0.2 for 6 minutes were obtained, respectively. The efficiency of this novel cleaning method was also compared to direct osmosis overnight, and the average flux was comparable (about 60%±3), though that the cleaning time was significantly different. Various calcium concentrations (0-10 mM) were added in the alginate solution to study the fouling behavior in terms of the potential for bulk complexation to form cake alginate layer on the membrane surface rather than a gel layer, and the role of CO2 bubbles nucleation to remove foulants was investigated. This cleaning method can be considered as an alternative more environmentally friendly technique in RO application.

Inorganic nano- and micromaterials (NMMs) exhibit unique properties including high surface areas, tunable optical and electronic properties, low densities, thermal and chemical robustness, and catalytic capabilities, among others. One of the more novel subclasses of NMMs, metal-organic frameworks (MOFs), are crystalline porous coordination polymers consisting of metal nodes connected by organic linkers to form one-, two-, or three-dimensional frameworks. While the mechanism of MOF formation is complex, tuning the metal:ligand ratios, reaction temperature and vessel pressure, ligand concentration, modulator concentration, and H+ activity impacts particle size, morphology, dispersity, and isotropy of these materials. MOFs also exhibit post-synthetic modification capabilities, which, along with their tunable synthetic nature, make them promising candidates for composite materials such as functionalized nanofillers for reverse osmosis (RO) desalination. The work described herein investigates synthetic parameters of a zirconium-based porphyrinic MOF, PCN-222, to selectively control its crystal size, aspect ratio, and dispersity. Size-constrained PCN-222 was post-synthetically modified with fatty acids and zwitterions to be used as RO thin-film composite (TFC) membranes with improved membrane flux, salt rejection, and anti-fouling properties. The synthetic parameters of MOFs were also considered for the commercial scale-up of CO2 direct air capture (DAC) solid sorbents, including UiO-66, MIL-101-Cr, and Mg-MOF-74, to preserve CO2 uptake capacities between lab and industrial scales. / Doctor of Philosophy / Metal-organic frameworks (MOFs) are unique, highly porous materials that have garnered attention for their potential in many applications, including catalysis, drug delivery, energy, and gas storage. In this work, MOFs were produced for environmental applications, particularly for the conversion of salt water to drinkable water in a process known as reverse osmosis (RO) desalination. RO uses a thin membrane to separate dissolved salt, as well as organic materials such as decomposed organisms, from water. Though RO membranes are widely used commercially, they suffer from high costs and short lifetimes; however, their performance is improved through the incorporation of extremely small materials known as nanoparticles. MOF nanoparticles were grown small enough to be dispersed in the polymer matrix of the thin membrane, then functionalized to improve salt rejection and flux, or the speed at which clean water is produced from RO processes. They were also modified to improve lifetimes by preventing the build-up of organic materials on the surface. Besides clean water, MOFs were also prepared for capturing the greenhouse gas, CO2, directly from the air. Because MOFs can be made with many different functionalities, they are promising materials for many different research fields.

No / The water permeability constant, (K-w), is one of the many important parameters that affect optimal design and operation of RO processes. In model based studies, e.g. within the RO process model, estimation of W-w is therefore important There are only two available literature correlations for calculating the dynamic K-w values. However, each of them is only applicable for a given membrane type, given feed salinity over a certain operating pressure range. In this work, we develop a time dependent neural network (NN) based correlation to predict K-w in RO desalination processes under fouling conditions. It is found that the NN based correlation can predict the K-w values very closely to those obtained by the existing correlations for the same membrane type, operating pressure range and feed salinity. However, the novel feature of this correlation is that it is able to predict K-w values for any of the two membrane types and for any operating pressure and any feed salinity within a wide range. In addition, for the first time the effect of feed salinity on Kw values at low pressure operation is reported. Whilst developing the correlation, the effect of numbers of hidden layers and neurons in each layer and the transfer functions is also investigated. (C) 2014 Elsevier B.V. All rights reserved.

Poly(arylene ether sulfone)s are high-performance engineering thermoplastics that have been investigated extensively over the past several decades due to their outstanding mechanical properties, high glass transition temperatures (Tg), solvent resistance and exceptional thermal, oxidative and hydrolytic stability. Their thermal and mechanical properties are highly suited to a variety of applications including membrane applications such as reverse osmosis, ultrafiltration, and gas separation. This dissertation covers structure-property-performance relationships of poly(arylene ether sulfone) and poly(ethylene oxide)-containing random and segmented copolymers for reverse osmosis and gas separation membranes. The second chapter of this dissertation describes synthesis of disulfonated poly(arylene ether sulfone) random copolymers with oligomeric molecular weights that contain hydrophilic and hydrophobic segments for thin film composite (TFC) reverse osmosis membranes. These copolymers were synthesized and chemically modified to obtain novel crosslinkable poly(arylene ether sulfone) oligomers with acrylamide groups on both ends. The acrylamide-terminated oligomers were crosslinked with UV radiation in the presence of a multifunctional acrylate and a UV initiator. Transparent, dense films were obtained with high gel fractions. Mechanically robust TFC membranes were prepared from either aqueous or water-methanol solutions cast onto a commercial UDEL® foam support. This was the first example that utilized a water or alcohol solvent system and UV radiation to obtain reverse osmosis TFC membranes. The membranes were characterized with regard to composition, surface properties, and water uptake. Water and salt transport properties were elucidated at the department of chemical engineering at the University of Texas at Austin. The gas separation membranes presented in chapter three were poly(arylene ether sulfone) and poly(ethylene oxide) (PEO)-containing polyurethanes. Poly(arylene ether sulfone) copolymers with controlled molecular weights were synthesized and chemically modified to obtain poly(arylene ether sulfone) polyols with aliphatic hydroxyethyl terminal functionality. The hydroxyethyl-terminated oligomers and α-ω-hydroxy-terminated PEO were chain extended with a diisocyanate to obtain polyurethanes. Compositions with high poly(arylene ether sulfone) content relative to the hydrophilic PEO blocks were of interest due to their mechanical integrity. The membranes were characterized to analyze their compositions, thermal and mechanical properties, water uptake, and molecular weights. These membranes were also evaluated by collaborators at the University of Texas at Austin to explore single gas transport properties. The results showed that both polymer and transport properties closely related to PEO-content. The CO2/CH4 gas selectivities of our membranes were improved from 25 to 34 and the CO2/N2 gas selectivity nearly doubled from 25 to 46 by increasing PEO-content from 0 to 30 wt.% in polyurethanes. Chapter four also focuses on polymers for gas separation membranes. Disulfonated poly(arylene ether sulfone) and poly(ethylene oxide)-containing polyurethanes were synthesized for potential applications as gas separation membranes. Disulfonated polyols containing 20 and 40 mole percent of disulfonated repeat units with controlled molecular weights were synthesized. Poly(arylene ether sulfone) polyols and α,ω-hydroxy-terminated poly(ethylene oxide) were subsequently chain extended with a diisocyanate to obtain polyurethanes. Thermal and mechanical characterization revealed that the polyurethanes had a phase-mixed complex morphology. / Ph. D.