The Canterbury Earthquake Sequence (CES) of 2010-2011 produced large seismic moments up to Mw 7.1. These large, near-to-surface (<15 km) ruptures triggered >6,000 rockfall boulders on the Port Hills of Christchurch, many of which impacted houses and affected the livelihoods of people within the impacted area. From these disastrous and unpredicted natural events a need arose to be able to assess the areas affected by rockfall events in the future, where it is known that a rockfall is possible from a specific source outcrop but the potential boulder runout and dynamics are not understood. The distribution of rockfall deposits is largely constrained by the physical properties and processes of the boulder and its motion such as block density, shape and size, block velocity, bounce height, impact and rebound angle, as well as the properties of the substrate. Numerical rockfall models go some way to accounting for all the complex factors in an algorithm, commonly parameterised in a user interface where site-specific effects can be calibrated. Calibration of these algorithms requires thorough field checks and often experimental practises. The purpose of this project, which began immediately following the most destructive rupture of the CES (February 22, 2011), is to collate data to characterise boulder falls, and to use this information, supplemented by a set of anthropogenic boulder fall data, to perform an in-depth calibration of the three-dimensional numerical rockfall model RAMMS::Rockfall. The thesis covers the following topics: • Use of field data to calibrate RAMMS. Boulder impact trails in the loess-colluvium soils at Rapaki Bay have been used to estimate ranges of boulder velocities and bounce heights. RAMMS results replicate field data closely; it is concluded that the model is appropriate for analysing the earthquake-triggered boulder trails at Rapaki Bay, and that it can be usefully applied to rockfall trajectory and hazard assessment at this and similar sites elsewhere. • Detailed analysis of dynamic rockfall processes, interpreted from recorded boulder rolling experiments, and compared to RAMMS simulated results at the same site. Recorded rotational and translational velocities of a particular boulder show that the boulder behaves logically and dynamically on impact with different substrate types. Simulations show that seasonal changes in soil moisture alter rockfall dynamics and runout predictions within RAMMS, and adjustments are made to the calibration to reflect this; suggesting that in hazard analysis a rockfall model should be calibrated to dry rather than wet soil conditions to anticipate the most serious outcome. • Verifying the model calibration for a separate site on the Port Hills. The results of the RAMMS simulations show the effectiveness of calibration against a real data set, as well as the effectiveness of vegetation as a rockfall barrier/retardant. The results of simulations are compared using hazard maps, where the maximum runouts match well the mapped CES fallen boulder maximum runouts. The results of the simulations in terms of frequency distribution of deposit locations on the slope are also compared with those of the CES data, using the shadow angle tool to apportion slope zones. These results also replicate real field data well. Results show that a maximum runout envelope can be mapped, as well as frequency distribution of deposited boulders for hazard (and thus risk) analysis purposes. The accuracy of the rockfall runout envelope and frequency distribution can be improved by comprehensive vegetation and substrate mapping. The topics above define the scope of the project, limiting the focus to rockfall processes on the Port Hills, and implications for model calibration for the wider scientific community. The results provide a useful rockfall analysis methodology with a defensible and replicable calibration process, that has the potential to be applied to other lithologies and substrates. Its applications include a method of analysis for the selection and positioning of rockfall countermeasure design; site safety assessment for scaling and demolition works; and risk analysis and land planning for future construction in Christchurch.

The research presented in this thesis results from efforts to evaluate current design methodologies for safety benches in surface aggregate quarries. Proper bench design is important for preventing rockfall related accidents and injuries without wasting the reserves held in the benches. An in depth analysis has been performed using the results from 230 rockfall tests conducted at two surface quarries. The goal of this project is to give practitioners the tools they need for improved bench design. Principal Components and Cluster Analysis, techniques not previously applied to rockfall investigations, have been performed on the test data. The results indicate that both are valid analytical methods which show that the factors affecting the rollout distance of a rock are wall configuration, rock dimensions, and rock energy. The test results were then compared to the Ritchie Criteria, Modified Ritchie Criterion, Ryan and Pryor Criterion, Oregon Department of Transportation design charts, and RocFall computer simulations. Analysis shows that the lognormal distribution curves fitted to the test data provide an excellent yet quick design reference. The recommended design method is computer simulation using RocFall because of the ease of simulation and the site specific nature of the program. For the two quarries studied, RocFall analysis showed that 20 ft benches with a 4 ft berm will hold over 95% of rockfalls, a design supported by the field testing. Conducting site-specific rockfall testing is also recommended to obtain realistic input parameters for the simulations and to provide design justification to regulatory agencies. / Master of Science

No description available.

No description available.

This thesis is concerned with modelling rockfall parameters associated with cliff collapse debris and the resultant “ramp” that formed following the high peak ground acceleration (PGA) events of 22 February 2011 and 13 June 2011. The Christchurch suburb of Redcliffs, located at the base of the Port Hills on the northern side of Banks Peninsula, New Zealand, is comprised of Miocene-age volcanics with valley-floor infilling marine sediments. The area is dominated by basaltic lava flows of the Mt Pleasant Formation, which is a suite of rocks forming part of the Lyttelton Volcanic Group that were erupted 11.0-10.0Ma. Fresh exposure enabled the identification of a basaltic ignimbrite unit at the study site overlying an orange tuff unit that forms a marker horizon spanning the length of the field area. Prior to this thesis, basaltic ignimbrite on Banks Peninsula has not been recorded, so descriptions and interpretations of this unit are the first presented. Mapping of the cliff face by remote observation, and analysis of hand samples collected from the base of the debris slopes, has identified a very strong (>200MPa), columnar-jointed, welded unit, and a very weak (<5MPa), massive, so-called brecciated unit that together represent the end-member components of the basaltic ignimbrite. Geochemical analysis shows the welded unit is picrite basalt, and the brecciated unit is hawaiite, making both clearly distinguishable from the underlying trachyandesite tuff. RocFall™ 4.0 was used to model future rockfalls at Redcliffs. RocFall™ is a two-dimensional (2D), hybrid, probabilistic modelling programme for which topographical profile data is used to generate slope profiles. GNS Science collected the data used for slope profile input in March 2011. An initial sensitivity analysis proved the Terrestrial Laser Scan (TLS)-derived slope to be too detailed to show any results when the slope roughness parameter was tested. A simplified slope profile enabled slope roughness to be varied, however the resulting model did not correlate with field observations as well. By using slope profile data from March 2011, modelled rockfall behaviour has been calibrated with observed rockfall runout at Redcliffs in the 13 June 2011 event to create a more accurate rockfall model. The rockfall model was developed on a single slope profile (Section E), with the chosen model then applied to four other section lines (A-D) to test the accuracy of the model, and to assess future rockfall runout across a wider area. Results from Section Lines A, B, and E correlate very well with field observations, with <=5% runout exceeding the modelled slope, and maximum bounce height at the toe of the slope <=1m. This is considered to lie within observed limits given the expectation that talus slopes will act as a ramp on which modelled rocks travel further downslope. Section Lines C and D produced higher runout percentage values than the other three section lines (23% and 85% exceeding the base of the slope, respectively). Section D also has a much higher maximum bounce height at the toe of the slope (~8.0m above the slope compared to <=1.0m for the other four sections). Results from modelling of all sections shows the significance of the ratio between total cliff height (H) and horizontal slope distance (x), and of maximum drop height to the top of the talus (H*) and horizontal slope distance (x). H/x can be applied to the horizontal to vertical ratio (H:V) as used commonly to identify potential slope instability. Using the maximum value from modelling at Redcliffs, the future runout limit can be identified by applying a 1.4H:1V ratio to the remainder of the cliff face. Additionally, the H*/x parameter shows that when H*/x >=0.6, the percentage of rock runout passing the toe of the slope will exceed 5%. When H*/x >=0.75, the maximum bounce height at the toe of the slope can be far greater than when H*/x is below this threshold. Both of these parameters can be easily obtained, and can contribute valuable guideline data to inform future land-use planning decisions. This thesis project has demonstrated the applicability of a 2D probabilistic-based model (RocFall™ 4.0) to evaluate rockfall runout on the talus slope (or ramp) at the base of ~35-70m high cliff with a basaltic ignimbrite source. Limitations of the modelling programme have been identified, in particular difficulties with adjusting modelled roughness of the slope profile and the inability to consider fragmentation. The runout profile using RocFall™ has been successfully calibrated against actual profiles and some anomalous results have been identified.

No description available.

No description available.

[pt] O trabalho propõe uma análise comparativa de modelos numéricos computacionais para simulação de processos de queda de blocos de rocha, assim como um estudo paramétrico com diferentes geometrias para avaliar trajetória dos blocos e a dissipação de energia cinética durante o evento. Para as simulações foram utilizados o software RAMMS Rockfall e o Método do Ponto Material (MPM). Ambos os métodos serão aplicados na análise de casos hipotéticos e reais de quedas de blocos na região sudeste do Brasil. módulo Rockfall do RAMMS, utiliza um algoritmo de corpo rígido para simular a queda dos blocos sobre um terreno tridimensional. utilizando-se de conceitos de dinâmica não suave com uma modelagem de contatos com restrições unilaterais e considerando a penetração do bloco na superfície através de uma abordagem simplificada. O MPM é um método numérico que combina as abordagens Lagrangeana e Euleriana, no qual o domínio geomecânico é discretizado em um conjunto de pontos materiais que armazenam as informações Lagrangeanas do problema, tais como velocidade e tensão, durante o processo de deformação e o espaço de análise é definido por uma malha Euleriana. Uma vez que, a cada passo de tempo, a malha retorna à configuração inicial, o MPM é livre de distorções, sendo adequado para análise de problemas de grandes deformações como queda de blocos de rocha. Para a resolução dos problemas através do Método do Ponto Material, será utilizado o simulador numérico computacional MPM- PUCRio, desenvolvido por Fernández (2020), onde as equações de movimento são resolvidas por meio de integrações explícitas. / [en] This dissertation puts forward a comparative analysis of computational numerical models to the simulatioh of rockfall processes, as well as a parametric study with different geometries, to evaluate the trajectory of the blocks and the dissipation of kinetic energy during the event. For the simulations, the RAMMS: Rockfall software and the Material Point Method (MPM) are operationalized. Both methods are applied in the analysis of hypothetical and real cases of rockfalls in Southeast Brazil. The RAMMS:Rockfall module employs a rigid body algorithm to simulate the rockfall on a three-dimensional terrain, exploring concepts of non-smooth dynamics with a contact modeling with unilateral constraints and considering the penetration of the block in the surface through a simplified approach. MPM is a numerical method that combines the Lagrangian and Eulerian approaches, in which the geomechanical domain is discretized into a set of material points that store the Lagrangian information of the problem, such as velocity and tension, during the deformation process, and the analysis space is defined by an Eulerian mesh. Once at each time step, the mesh returns to the initial configuration, MPM is distortion-free, being suitable for the analysis of large deformation problems, such as rockfalls. In order to solve problems using the Material Point Method, the numerical computational simulator MPM-PUCRio, developed by Fernández (2020) is mobilized. In this equipment, the equations of motion are solved through explicit integrations.

Faculty of Engineering and Built Enviroment School of Mining Engineering 0315711f musakale@egoli.min.wits.ac.za / Rockfalls are a significant risk in open pit mines. Once movement of a rock perched on the top of a slope (bench) has been initiated, the most important factor controlling its fall trajectory is the geometry of the slope (bench). The best possible knowledge of rockfall trajectories and energies is important in order to determine accurate risk zoning and for the design and construction of adequate defence systems near the threatened areas. This study attempts to determine the influence of bench geometries, and the coefficient of restitution of rock, on rockfall behaviour. A study of literature was carried out to review previous studies and other relevant information on rockfalls and their analysis. The literature may be divided into two categories: experimental methods involving physical modelling, and computer models involving rockfall analyses using computers analysis methods. Rockfall computer simulation is considered to be applicable, quick to carry out and reproducible. The accuracy of the results depends on the knowledge of site conditions and slope geometry. The use of the Modified Ritchie criterion for the design of catch benches in open pit mines was also investigated. The assessment of bounce height, maximum run-out distance and kinetic energy achieved during the fall of rocks on the catch bench were the bases of the evaluation of the results obtained in this project. The computer program, Rocfall Version 4, was used for the purposes of the research. The following parameter variables were considered in the analyses: three types of rock; slopes with three stack configurations; four bench heights; and four bench face angles. The results show that, for all stack configurations and rock types, the maximum runout distance and maximum bounce height increase as functions of bench height at a specific bench face angle. A single bench configuration provides a maximum run-out distance of falling rocks larger than the value determined using the Modified Ritchie criterion for all rock types and bench face angles. Multiple bench stack configurations provide maximum run-out distances less than the value determined using the Modified Ritchie criterion only for the 90o bench face angle in all rock types; those with 60o, 70o and 80o bench face angle provide a larger maximum run-out distance. Therefore, the validity of the Modified Ritchie criterion for the design of catch bench widths in open pit mines with inclined benches must be questioned. According to Ritchie’s study (1963), rocks that fall in trajectory (free fall) seldom give high bounces after impact on a catch bench. This project shows that this finding is valid for rocks with low coefficients of normal restitution. Rocks with lower coefficients of normal restitution provide larger run-out distances with flatter bench face angles compared with rocks with higher coefficients. In contrast, rocks with higher coefficients provide larger run-out distances than those with lower coefficients for steeper angles. The consideration of the influence of geometry (shape) of falling rocks on rockfall behaviour showed that, for a flatter slope, as could logically be expected, the maximum run-out distance is greatest for rounder rocks and smallest for flatter slabby iv rocks. This is due to the fact that on a flatter slope, the mode of falling of rounder rocks is rolling down the slope. This mode provides essentially no resistance to motion, resulting in largest maximum run-out distance. In contrast, for long flat slabs, the mode of movement will be sliding, which results in a smaller maximum run-out distance. The maximum run-out distance as function of rock shape reduces as the normal coefficient of restitution increases. For all rock types, the maximum bounce height reduces as a function of the friction angle for flatter slopes. This is due to the fact that rocks are in contact with the slope during the rockfall. As the coefficient of normal restitution increases, an increase in the maximum bounce height results.

The study area, which will be open to tourism in Kusadasi (Aydin), has steep and high cliffs near the Aegean coast. In the area where some slidings and rockfall problems occurred in the past the geological hazards should be investigated and nature-friendly remedial measures should be taken. The aim of this study is to perform engineering geological studies to:(i) search geological hazards, (ii) reveal the slope stability problems, (iii) recommend nature-friendly solutions in order to prevent/minimize the hazards and (iv)compare the results obtained from 2-D and 3-D rockfall analyses. To accomplish these tasks, the geological survey was performed, the information about the discontinuities was collected by means of scanline surveys, the rock samples were collected, the in-situ and laboratory tests were carried out, the slope stability and rockfall analyses were performed for different slope conditions, remedial measures were offered for the problematical areas considering the data obtained and the results of 2-D and 3-D analysis were compared. Under the light of these studies, rock removal, drainage, greening (vegetation), filling the caverns, wall building and erosion prevention were offered as remedial measures. The comparison of the 2-D and 3-D rockfall analyses shows that the end points and bounce height values are different for each method. The differences between the 2-D and 3-D model originate from the slope geometry, the algorithm used in the software and the different input parameters. According to the field observations, the 2-D model is more realistic than 3-D model.