No description available.

No description available.

<p>  </p> <p>In the practical applications of colloidal dispersions and suspensions, such as inks, paints, and food industry, the suspended particles must be stabilized, and remain well-dispersed for long times. Particles which are more dense than the suspending media may sediment rapidly, even with no agglomeration occurring, under many conditions of size and density difference. Then, a dispersant would be necessary for stabilization of particle suspensions against both agglomeration and sedimentation, while the suspensions should remain flowable in many applications. Moreover, when many aqueous suspension media may contain salts, the dispersant also needs to be an effective stabilizer against sedimentation under the specific salinity conditions of that application.</p> <p>DDAB (didodecyldimethylammonium bromide) , a cationic double-chain surfactant, forms lamellar liquid crystal phases when dispersed in water. It also easily forms aqueous vesicle dispersions (unilamellar closed particles with an internal solvent compartment) and liposomes (multilamellar vesicles, MLVs, or lamellar liquid crystallites) at relatively low DDAB weight fractions, <em>w</em>_D. To better understand the phase/dispersion behavior of DDAB and the corresponding optical properties, new analytical solutions of the spherical particles have been obtained for the light scattering theory in the Rayleigh (R) and the Rayleigh-Debye-Gans (RDG) regimes, for single and independent scattering. Moreover, the specific Rayleigh ratio <em>R</em>_q** and the specific turbidity <em>t</em>** were derived analytically for both scattering regimes. Spectroturbidimetry (ST) data at 25 °C for DDAB were compared to the <em>t</em>** predictions. <em>t</em>** data for DDAB vesicles are consistent with the RDG predictions, which are also used to estimate the vesicle sizes.</p> <p>For a better understanding of the effect of the preparation method and salinity on the formation of DDAB vesicles, spectroturbidimetry was used to measure the average radius of the unilamellar DDAB vesicles, which were prepared via two different methods in water and in NaBr salt solutions. The radius was ~24 nm after sonication (SS method) and ~74 nm after extrusion/ultrafiltration (SE method). The radii were larger when the vesicles were produced in 10 mM NaBr, ~65 nm for the SS method and ~280 nm for the SE method. The <em>t</em>** values of these vesicular dispersions increased with decreasing <em>w</em>_D values, until a constant value was reached at <em>w</em>_D*, which depends on the preparation method and the dispersion medium. The constant values of <em>t</em>** are indicative of single and independent scattering, and were used to estimate vesicle radii by solving the <em>t</em>** equations derived for the RDG regime. Estimates of the average distances between the vesicles and their corresponding Debye lengths were obtained to evaluate the importance of inter-vesicle electrostatic interactions, which could lead to dependent scattering at higher weight fractions.</p> <p>DDAB prepared with magnetic stirring of multilamellar liposomes, followed by ultrasonication to generate unilamellar vesicles, were found to have very high viscosities at very low shear stresses at DDAB weight fractions <em>w</em>D from 0.025 to 0.027. The vesicles had average diameters ranging from 68 to 80 nm, as previously determined from spectroturbidimetry. These vesicle dispersions stabilized suspensions of monodisperse spherical amorphous silica particles with diameters of <em>d</em>_sed = 454 nm, 691 nm, and 826 nm against sedimentation, at least for several weeks. Similar results were obtained for suspensions, in DDAB vesicle dispersions, of polydisperse, nonspherical, crystalline titania particles with sizes ranging from ca. 96 nm to 156 nm. At the relatively low values of <em>w</em>_D = 0.009 and 0.018, the effective viscosities,<em> h</em>eff, of the DDAB dispersions, determined from the sedimentation velocities, ranged from 1.35 to 1.87 cP and from 4.34 to 5.57 cP, respectively. At <em>w</em>_D = 0.027 for the silica particles with <em>d</em>_sed = 454 nm, or at <em>w</em>_D = 0.025 for all other particles considered, <em>h</em>_eff was essentially infinite, and each vesicle dispersion behaved as a gel at low shear stresses. At higher shear stresses, however, the dispersions were highly shear-thinning, and flowable in a capillary tube under gravity. This behavior is critical for the practical applications of such dispersions for paints and inkjet printing. To further understand the feasibility of the vesicle stabilization mechanism at various NaBr concentrations, <em>w</em>NaBr, the salinity effects on the stabilization of silica particles against sedimentation were also examined. It was found that at <em>w</em>_NaBr < 0.0020 and at <em>w</em>D > 0.060, the DDAB dispersion could stabilize silica particles against sedimentation for at least two weeks. The relationship of the phase and dispersion behavior of DDAB/aqueous NaBr solutions to their stabilizing effectiveness will be further studied.</p> <p>A first discovery of iridescent liquid-like aqueous vesicle dispersions formed from the DDAB is also reported. Although iridescence arises from some solid crystallites, thin films, and colloidal crystals, it had never been observed in systems that are liquid-like. Visual observations and ST at wavelengths of 350 nm to 700 nm were used to determine vesicle sizes and microstructure formation in dispersions for DDAB weight fractions <em>w</em>D between 0.020 to 0.030. The DDAB vesicle dispersions exhibited iridescent colors for <em>w</em>D = 0.023 to 0.027, due to the formation of “soft” crystallites formed by self-assembled vesicles. Effective vesicle radii from 30 to 60 nm were inferred from the ST measurements. The volume fractions of the vesicles <em>f</em>v and their effective volume fractions <em>f</em>v*, which account for the electrostatic double layers around a vesicle, were also estimated. The high values of <em>f</em>v* for the iridescent dispersions indicate that they contain neighboring vesicles with highly overlapping electrostatic double layers, even though their values of <em>f</em>v remain relatively low. Hence, strong electrostatic repulsive interactions arise between the vesicles. These interactions probably drive the formation of the “soft” crystallites, and thus the observed iridescence. Nevertheless, these “soft” crystallites, which could be easily broken up but were quick to reform, remain suspended. Consequently, these vesicle dispersions still flowed as a bulk dispersion with a high viscosity; the dispersion as a whole remained liquid-like or as a “liquid gem”, in contrast to what occurs to the other colloidal crystals made of rigid colloids. Beside their beautiful appearances, these DDAB vesicle dispersions also act as effective stabilizers of dense silica suspensions against sedimentation even at relatively low values of <em>w</em>D. </p>

The focus of the thesis research was to investigate the surface reactivity of three different minerals, pyrite (FeS2), an ordered form of ferrihydrite (an iron oxyhydroxide phase), and birnessite (MnO2), toward environmentally relevant aqueous reactants. In particular, research was carried out with the goals of 1) understanding the redox chemistry of nitrite (NO2-) and nitrate (NO3-) on pyrite and 2) understanding the redox (photo) chemistry of arsenite (AsO2-, As(III)) on ordered ferrihydrite and birnessite. A motivation for all these studies stemmed in part from the recognition that NO2-, NO3-, and As(III) are all environmental pollutants when they are present at sufficiently high concentration in the environment. The removal of these species or conversion of each of them on mineral surfaces to more benign chemical species is of importance in the realm of environmental chemistry. In the case of NO2- and NO3- on pyrite, an additional and primary motivation for the research was that it has been hypothesized in the "origin-of-life" community that the reaction of NO2- and NO3- with iron sulfide (e.g., pyrite) may have played a role in the production of ammonia (NH3) on early Earth. Such prebiotic chemistry had been hypothesized to an essential step in the production of biomolecules that included proteins. With regard to the NO2- reaction with pyrite, results detailed in this thesis showed that ammonia in µmol/kg quantities could be produced by reacting NO2- in the presence of pyrite under anaerobic conditions. The concentration of NH3 (detected as ammonium, NH4+, in solution) was a strong function of the reaction temperature. At the lower temperatures studied (22oC and 70oC), a small amount of NH4+ was formed, but µmol.kg-1 amounts of NH4+ were formed at a reaction temperature of 120oC. Only about 5% of the initial NO2- concentration was converted to NH4+. In the NO3-/pyrite system, the NO3- reactant concentration remained unchanged at all the three reaction temperatures studied, consistent with the low amounts of NH4+ formed in these experiments. Finally, it was shown using in situ infrared spectroscopy that surface-bound NO formed on pyrite during the conversion of the nitrogen oxides to ammonia. Overall, it was shown that the kinetics of NH4+ formation was slower for NO3- than that observed for NO2-. Studies presented in this thesis that focused on the surface reactivity of As(III) on ordered ferrihydrite and birnessite nano particles showed that As(III) could be oxidized to arsenate (referred to as As(V)) in the presence of simulated solar radiation. In the ordered ferrihydrite circumstance the adsorption of As(III) and photo-induced oxidation to As(V) was compared to the same reaction on the more disordered and smaller ferrihydrite particles (known as "2-line" ferrihydrite). A comparison of the adsorption rate of As(III) on the two surfaces in the presence of light after normalizing for differences in surface area showed that the ordered ferrihydrite exhibited a higher arsenic adsorption rate. Also, the oxidation rate of As(III) to As(V) in the presence of light on the ordered ferrihydrite showed a strong dependence on the amount of dissolved oxygen in solution while the oxidation rate on the more disordered form showed no such dependence. It was proposed that differences in the rates of the heterogeneous oxidation rate of ferrous iron with dissolved oxygen on the two surfaces were the reason for this behavior. Finally, the photo-induced oxidation of As(III) to As(V) on Na- and K-birnessite at solution pHs of 5.0 and 7.4 was investigated. It was shown that the oxidation rate of As(III) to As(V) occurred at a faster rate on birnessite in the presence of light when compared to the same system in the dark. Mn(II) formed during the reductive dissolution of birnessite during the oxidation of As(III) was experimentally observed at pH 5.0, but not at pH 7.4. Experiments were also conducted that investigated the reductive dissolution of Na- and K-birnessite (having different sizes and average oxidation states) by As(III) under more alkaline conditions. These experiments were conducted at pH 8.5 and the post-reaction samples were analyzed with X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). It was shown under these alkaline conditions using X-ray diffraction that structural changes occurred in/on both the Na- and K-birnessite during the As(III) oxidation reaction. / Chemistry

Call number: LD2668 .T4 1985 S25 / Master of Science

Thesis (MSc)--Stellenbosch University, 2003. / ENGLISH ABSTRACT: In this thesis the formation and properties of a polymer gel on and at a surface are investigated. The gel under investigation is defined as a three-dimensional network of macromolecules that form permanent links with one another and also with confining planar surfaces. The precise location of the crosslinks on the wall or on another macromolecule is not known prior to linking, and will differ from sample to sample. However, once the crosslinks are formed, they are assumed to be permanent. This random linking is the source of the disorder in the system, over which a quenched average has to be taken. An existing model [9] of network formation, with polymer-polymer crosslinks, is extended to incorporate a surface and polymersurface crosslinks. Within the framework of replica theory, statistical averages and physical properties of the system are calculated by means of a variational approach. Macroscopic information, in terms of the free energy of deformation, is obtained by using two different potentials to simulate the erosslinks mathematically. / AFRIKAANSE OPSOMMING: In hierdie tesis word die vorming en eienskappe van 'n polimeergel, wat teen 'n oppervlak gevorm word, ondersoek. Die gel word gedefinieer as 'n drie-dimensionele netwerk van makromolekules wat permanente bindings met mekaar, maar ook met twee inperkende, platvlakke, vorm. Die presiese ligging van die bindings op die muur en op ander makromolekules is nie vooraf bekend nie, en sal verskil van een gel-monster tot die volgende. Sodra die konneksies egter gevorm is, word aanvaar dat hulle permanent is. Die lukrake bindingsproses is die oorsprong van wanorde in die sisteem, waaroor 'n wanorde-gemiddelde bereken moet word. 'n Bestaande model [9]van netwerkvorming, met polimeer-polimeer bindings, word uitgebrei om 'n oppervlakte en polimeer-oppervlak bindings in te sluit. Statistiese fisika gemiddeldes en fisiese eienskappe van die sisteem word binne die raamwerk van replika-teorie en 'n variasie benadering bereken. Makroskopiese inligting, in terme van die vrye energie van vervorming, word verkry deur twee verskillende potensiale te gebruik om die konneksies wiskundig voor te stel.

No description available.

Several phenyl alkyl bonded phases for liquid chromatography were synthesized and characterized by liquid chromatography, gas chromatography and ¹³C nuclear magnetic resonance (NMR) spectroscopy. The chromatographic physical parameters investigated include a quantitative determination of the mobile phase volume and the stationary phase volume. The stationary phase volume was determined to be a function of the bonded moiety chain length and the chromatographic solvent system employed. The interpretation of the stationary phase volume is discussed in terms of the porous nature of the silica gel support. The chemical parameters determined include a quantitative determination of the mobile phase and stationary phase composition (which were different from each other). The selectivity of the chromatographic separations was dependent on the chemical composition and the volume of both the stationary and mobile phases. Carbon 13 NMR spectroscopy provided information about the environment of the bonded moiety in the stationary phase. The liquid-like nature of the bonded moiety was influenced by the chain length of the attached species, the choice of organic modifier, and the chemical composition of the solvents. Temperature did not appear to play a role in the line widths under the experimental conditions examined. The separation of several peptide diastereoisomers on different commercially available hydrocarbon bonded adsorbents is also reported. Select diastereoisomers of arginine vasopressin and oxytocin are extremely sensitive to differences in the composition of the stationary phase. The selectivity and elution order were dependent upon the choice of adsorbent and solvent system employed. The addition of a second organic modifier provided a method for the dynamic modification of the stationary phase. The ability to dynamically modify the stationary phase can enhance the selectivity for the separation of selected peptide diastereoisomers.

When solutions of various metal 8-quinolinolates or beta-diketonates in an organic solvent were contacted with an aqueous phase and vigorously stirred to generate a large interfacial area, a reversible decrease in the organic phase concentration of the complex was observed. The magnitude of this decrease varied with interfacial area, solvent, temperature, and the nature and concentration of the complex. Analysis of the phenomenon using the Langmuir isotherm showed that the concentration change may be explained by adsorption of significant quantities of the complexes at the increased liquid-liquid interface generated by stirring. Such adsorption was found to complicate extraction kinetics measurements using the high-speed stirring technique when the product chelate is interfacially active, distorting the absorbance/time profile from which rate constants are derived, altering the interfacial area in the reaction vessel, and displacing reactant molecules from the interface. Neutral surfactants were observed to have similar effects. Chelate adsorption was also demonstrated to affect metal ion extraction equilibria, shifting the pH 1/2 value associated with a given metal ion. The magnitude of this shift was found to depend on the concentration of the chelate, its interfacial adsorption constant, and interfacial area. Differences in the pH 1/2 shift were shown to serve as a means of separating metal ions. Studies of the rate of nickel extraction by 8-quinolinols showed that the distribution constant and interfacial activity of the ligand are important factors governing the balance between bulk and interfacial pathways in the extraction. The interfacial rate constant for a given ligand was independent of organic solvent and was typically 10 times larger than the corresponding bulk value, indicating that the interface, although essentially aqueous in character, is a more conducive medium for the reaction of the metal ion and ligand.

A new theory has been proposed for stationary phase formation of chemically modified chromatographic adsorbents. This theory consists of a model in which the bonded hydrocarbon moiety, silica substrate, and their respective solvation layers all participate in stationary phase formation. Stationary phase formation was found to be dependent on three parameters: (1) Solvent strength of the mobile phase components for the bonded organic moiety and the silica substrate; (2) the type of organic moiety covalently bound to the surface; and (3) the bound moiety density or surface coverage. Binary aqueous-organic mobile phases were investigated for LiChrosorb RP-8 and RP-18. For RP-8 the solica substrate played a more important role in stationary phase formation. Whereas, for RP-18 the longer bound hydrocarbon chain dominated stationary phase formation. With different organic modifiers in the mobile phase, the modifier with the larger solvent strength for the bound hydrocarbon was selectively enriched in the stationary phase solvation layer for RP-18. Ternary mobile phase systems were also investigated for RP-18. The second modifier was found to exert a large influence on stationary phase formation. Temperature's role in stationary phase formation was studied with a ternary mobile phase of 40/45/15 methanol, water, THF with RP-18. In this specific case, changing the temperature of the system did not impact on stationary phase formation. A new type of column structure was investigated. This structure involved a totally porous silica gel as compared to a column packed with totally porous silica microparticles. These silica gel columns were characterized both thermodynamically and kinectically. Under Normal Phase chromatographic conditions the silica gel column was found to have a higher selectivity but poorer efficiency for the separation of aniline from nitrobenzene than a packed column. The silica gel can be chemically modified by silane reaction and its bonded phase characteristics were investigated. The gel also showed ion-exchange properties which were investigated using sodium nitrite.