The subject of the diploma thesi is the design and assessment of the pavilions supporting structure for exhibition and other purposes. The building is located close to Zlin. Preliminary designs of supporting structure were created. One of these was selected and detaileddesigned and assessed. Generallythere are two structures that are extended between themselves. A design and assessment of the entrance portal for the exhibition pavilion was created. The entrance portal is an atypical structure that was created from a combination of hyperboloid and cylinder. The entire portal is formed of welded parts and it is completely from glass. The entrance portal has a variable height, where the highest point is 8,258m. The entrance portal is 20,394m long and has a variable width, where the largest width is 12,000m. The exhibition hall, which is located behind the entrance portal was designed from flat arched truss trusses. The arched trusses are made of several radii and hasa overall impression of an elliptical truss. The trusses have a range 37,000m and they are axially distant 6,000m. The height of the arched trusses is 10.530m. In the leading position of the construction were designed pillars and construction for possible connection of the entrance portal, or for the location of the gate system. Whole construction of the exhibition pavilion, without the entry portal, is 54,000m long and 37,000m wide. The built-up area of both structures is approximately 2200m2. Construction are designed according to normative requirements of CSN EN for limit state of load capacity and usability. The main material of the supporting structural parts was used S355JR steel.

This diploma thesis describes the design of hut with accomodation and restaurant. The hut is situated in Jeseníky mountains. The house is designed as detached house made of clay blocks, with timber roof truss and gable roof. The building has three floors, first one is particulary embedded under the terrain. On the ground floor there is garage, technical and storage rooms. Restaurant with kitchen, toilets,rooms for employees, reception and barrier-free guest room is located on the first floor. On the second floor there are guest and employee rooms.

The master thesis focuses on the design of a Load-carrying steel structure of railway bridge with bottom steel deck of the span of 28 + 45 + 23 m. The bridge is situated in the municipality of Třebestovice. Four variants of solution have been calculated. Two variants are made by plate main beams of variable profile, the next alternative was made by truss structure and the fourth variant consist of a combination of plate main beams with truss stiffener in the middle span. The most optimal solution was processed in detail. The calculations were done in compliance with valid ČSN EN norms.

The subject of my diploma thesis is to design and assess a multipurpose sports hall in the area of Brno-Bystrc. The shape of the hall is rectangular with dimensions 45 m × 48 m. The roof is designed from an arched truss. The height of the construction is 18 m. Part of the thesis is a technical report which contains details of construction, list of used materials, production and maintenance method. The work also includes the static calculation of supporting elements and joints and the graphical documentation. The valid CSN EN technical standards were used for the design and assessment.

This diploma thesis is dealing with the solution of four-floor mountain guesthouse with one floor underground and three floor overground on parcel 1953/16 in Low Tatras, Slovak republic. The parcel is situated in the cadastral region of Horná Lehota. The design of the mountain guesthouse is solving the architectonical, technical and building solutions of the object according to the requests of investor. Underground floor is designed from DT concrete blocks, which are waterproofed by the bitumen felts and thermally insulated by the extruded polysytrene. Overground floors are made from ceramic blocks HELUZ and thermally insulated by ETICS system from mineral wool. The roof of the object is made from pitched roof constructed from timber trusses, which are connected by gangnail steel sheets. The purpose of this project is to create modern and comfortable builidng, which provides pleasant environment mainly for fans of tourism and downhill skiing, but also for other visitors.

The aim of the thesis is to design and appreciation steel load-bearing structure of motor show. The object is situated in Brno. The Structure consist of tubes and rolling sections. The breadth of construction is 36,5m, lenght 42m and height in the heihest point is 13,2m. The structrure is consists of three parts. Show room, offices and workshop. The height of show room is 20m, offices 8,5m and workshop 8m. The show room consist of arched truss girder. The distance of each cross links is 6 m. Structural design were perfomered by Scia Engineer 2017 and hand computation.

Thesis deals about the building structural condition of the building in Šlapanice, street Riegrova 1238/21. Methods of diagnostic survey are suitably chosen, then realized and evaluated. From these results is done structural calculation of bricks pillar in first-floor. We reached to the conclusion, that the most suitable solution is demolition of this existing object and build the new one.

By submitting my thesis I designed three variants of the steel construction of the motor show. The ground dimensions of the entire structure are 56 x 40 m. The building eaches a height of 21 m above the surrounding terrain. The object is the administrative part of the rectangular ground plan and the exhibition space of the perimeter ground plan. The circular part is a covered dome. Variants differ in design of the radial arc cross section in the dome cover. Part of the main structural elements. The winning variant includes a solution of selected details elaboration of detailed drawings of solved connections and creation of workshop documentation of the selected work.

The subject of the diploma thesis is an architectural study of a velodrome in Brno Komárov. It is an indoor cycling track which is still missing in the Czech Republic. The whole site of the Hněvkovského sports complex in Komárov was elaborated within the architectural study. The aim of the proposal was to attract a wide range of visitors to the site, so not only buildings for sports were designed. But also two sets of buildings as a modular construction from containers providing premises for rent. The construction of the velodrome was deign as a combination of monolithic reinforced concrete and steel truss structure. The cladding is design from insulated panel system.

The object of this thesis is to design and assess the roofing of concrete terraces on stadium Za Lužánkami in Brno. Rectangular plan of steel structure is 100x25 m. The main Girders are 5 m apart and are pin-supported. Girders are placed on concrete footings and supported by center columns. Roof cladding is connected with hot-rolled purlins. Two construction variants were designed and assessed. Variant A, where the main girders are made of welded beams (I shaped) and variant B, where the main girders are made of truss. Variant B was chosen as better option for this structure.