The temperature of the flow entering a high-pressure turbine stage is inherently non-uniform, as it is produced by several discrete, azimuthally-distributed combustors. In general, however, industrial simulations assume inlet temperature uniformity to simplify the preparation process and reduce computation time. The effects of a non-uniform inlet field on the performance of a commercial, transonic, single-stage, high-pressure, axial turbine with a curved inlet duct have been investigated numerically by performing URANS (Unsteady Reynolds-Averaged Navier-Stokes equations) simulations with the SST (Shear Stress Transport) turbulence model. By adjusting the alignment of the experimentally-based inlet temperature field with respect to the stator vanes, two clocking configurations were generated: a vane-impinging (VI) case , in which each hot streak impinged on a vane; and a mid-pitch (MP) case, in which each hot streak passed between two vanes. In the VI configuration, the hot streaks produced higher time-averaged heat load on the vanes and lower heat load on the blades. As the hot streaks in the VI case passed over the stator vanes, they also spread spanwise due to the actions of the casing passage vortices and the radial pressure gradient; this resulted in a stream entering the rotor with relatively low temperature variations. The hot streaks in the MP case were convected undisturbed past the relatively cool vane section. Relatively high time-averaged enthalpy values were found to occur on the pressure side of the blades in the MP configuration. The non-uniformity of the time-averaged enthalpy on the blade surfaces was lower in the VI configuration. The flow exiting the rotor section was much less non-uniform in the VI case, but differences in calculated efficiency were not significant. / Pratt & Whitney Canada, NSERC

Test results from a rocket turbine test model, called the Oxidizer Technology Turbine Rig (OTTR), are discussed in this paper. The turbine was designed to support the development of advanced turbines for future liquid rocket engines. It is a highly loaded single stage liquid oxygen pump drive turbine which uses inlet and exit volutes to provide optimum performance in a compact configuration. The system design creates high pressure and temperature gradients as well as high Mach number flow. These factors make it especially difficult to accurately measure the flowfield. Test issues such as probe calibration; probe interference, rake blockage, and averaging techniques were discussed in a previous paper. Test results including inlet volute, exit volute (both circular and square), and diffuser static pressure distributions, stator airfoil static pressure distributions, total and static pressure drops through the system, and overall performance parameters at the turbine aerodynamic design point and off-design point are presented here. This thesis will mainly focus on the information of both aerodynamic design point and off-design point of inlet volute, exit volute and diffuser for both circular exit volute and square exit volute.

Thermoacoustic instabilities arise and sustain due to the coupling of unsteady heat release from the flame and the acoustic field. One potential driving mechanism for these instabilities arise when velocity fluctuations (u') at the fuel injection location causes perturbations in the local equivalence ratio and is convected to the flame location generating an unsteady heat release (q') at a particular convection time delay, τ. Physically, τ is the time for the fuel to convect from injection to the flame. The n-τ Flame Transfer Function (FTF) is commonly used to model this relationship assuming an infinitesimally thin flame with a fixed τ. In practical systems, complex swirling flows, multiple fuel injections points, and recirculation zones create a distribution of τ, which can vary widely making a statistical description more representative. Furthermore, increased flame lengths and higher frequency instabilities with short acoustic wavelengths challenge the 'thin-flame' approximation. The present study outlines a methodology of using distributed convective fuel time delays and heat release rates in a one-dimensional (1-D) linear stability model based on the transfer matrix approach. CFD analyses, with the Flamelet Generated Manifold (FGM) combustion model are performed and probability density functions (PDFs) of the convective time delay and local heat release rates are extracted. These are then used as inputs to the 1-D Thermoacoustic model. Results are compared with the experimental results, and the proposed methodology improves the accuracy of stability predictions of 1-D Thermoacoustic modeling. / Master of Science / Gas turbines that operate with lean, premixed air-fuel mixtures are highly efficient and produce significantly lesser emission of pollutants. However, they are highly susceptible to self-induced thermoacoustic oscillations which can excite larger pressure fluctuation which can damage critical components or catastrophic engine failure. Such a combustion system is considered to be unstable since the oscillation amplitude increases with time. Understanding the non-linear feedback mechanisms driving the system unstable and their cause are naturally of high interest to the industry. Highly resolved, but computationally demanding simulations can predict the stability of the system accurately, but become bottlenecks delaying iterative design improvements. Low order numerical models counter this with quick solutions but use simplified representations of the flame and feedback mechanisms, resulting in unreliable stability predictions. The current study bridges the gap between these methods by modifying the numerical model, allowing it to incorporate a better representation of fluid flow fields and flame structures that are obtained through computationally cheaper simulations. Experiments are conducted to verify the predictions and a technique that can be used to identify regions of the flame that contribute to amplitude growth is introduced. The improved model shows notable improvement in its prediction capabilities compared to existing models.

The presented work deals with basic characteristics of the side-channel machines. The intention is to replace the pressure reducing valve by low-specific speed side-channel turbine. Thereby creating a kind of turbine valve using energy, which would otherwise be dissipated in the valve. Pressure reducing valves are the source of large hydraulic losses and their replacement is possible, because the same resistance characteristics side-channel turbine and a pressure reducing valve.

No description available.

No description available.

No description available.

No description available.

No description available.

No description available.