This master's thesis investigates if it is possible to increase the size of the simulations running on NETSim, Network Element Test Simulator, on a specific hardware and operating system. NETSim is a simulator for operation and maintenance of telecommunication networks. The conclusions are that the disk usage is not critical and that it is needless to spend time optimizing disk and file system parameters. The amount of memory used by the simulations increased approximately linear with the size of the simulation. The size of the swap disk space is not a limiting factor. / Detta exsamensarbete undersöker om det är möjligt att öka storleken på simuleringskörningar av NETSim, Network Element Test Simulator, på en specifik hårdvaru- och operativsystemsplattform. NETSim är en simulator för styr och övervakning av telekomnätverk. Slutsatserna är att diskanvändandet inte är kritiskt och att det är onödigt att ägna tid åt att optimera disk- och filsystemsparametrar. Minnesutnyttjandet ökar approximativt linjärt med storleken på simuleringarna. Storleken på swapdisken är inte någon begränsande faktor.

Silicon CMOS Technology is now the preferred process for low power wireless communication devices, although currently much noisier and slower than comparable processes such as SiGe Bipolar and GaAs technologies. However, due to ever-reducing gate sizes and correspondingly higher speeds, higher Ft CMOS processes are increasingly competitive, especially in low power wireless systems such as Bluetooth, Wireless USB, Wimax, Zigbee and W-CDMA transceivers. With the current 32 nm gate sized devices, speeds of 100 GHz and beyond are well within the horizon for CMOS technology, but at a reduced operational voltage, even with thicker gate oxides as compensation. This thesis investigates newer techniques, both from a systems point of view and at a circuit level, to implement an efficient transceiver design that will produce a more sensitive receiver, overcoming the noise disadvantage of using CMOS Silicon. As a starting point, the overall components and available SoC were investigated, together with their architecture. Two novel techniques were developed during this investigation. The first was a high compression point LNA design giving a lower overall systems noise figure for the receiver. The second was an innovative means of matching circuits with low Q components, which enabled the use of smaller inductors and reduced the attenuation loss of the components, the resulting smaller circuit die size leading to smaller and lower cost commercial radio equipment. Both these techniques have had patents filed by the University. Finally, the overall design was laid out for fabrication, taking into account package constraints and bond-wire effects and other parasitic EMC effects.

The master thesis is focused on the Universal Mobile Telecommunications System (UMTS) - the third-generation cell phone technology. The first part describes the development of mobile networks and the structure of the UMTS. The second part, the main part of the thesis, is focused on the planning procedure of the UMTS access network. It consists of an explanation of the general planning procedure and a specific project designing the coverage of Pelhřimov surroundings. The final part of the thesis contains a laboratory problem including instructions.

This thesis concentrates on the UMTS cellular network and the possibilities of its monitoring. There are several methods of monitoring the UMTS. The technique used in this project is based on monitoring through a cellular terminal. The theoretical part is devoted to the description of the UMTS system and the WCDMA technique. The practical part then deals with the method of UMTS monitoring through a cellular terminal and describes in detail individual screens of the FTD (Field Test Display) program, the Netmonitor functions and their parameters. The next part of this thesis analyses the RRC messages, which were recorded during the realization of services (video calls, calls, data transfers) in the UMTS network. The last chapters of the thesis are briefly dealing with software and hardware servicing of cellular terminals. The attachment then offers two lab tasks, in which the students get acquainted with the UMTS network structure and the behaviour of the cellular terminal in this network.

Diploma thesis deals with assign and distribution quality of service in mobile UMTS telecommunication networks. The project consists of two parts, theoretical and practical. Theoretical part of the project is focused to familiarize with functionality of the UMTS network with the main aspect at admission mechanism in radio part of the network as well as quality of service assign mechanisms according to service demands within core network of UMTS. Practical part of the project is given to simulation program OPNET Modeler and its capabilities in network design and testing various parameters of UMTS network with implementation quality of service mechanism. As the asset of diploma thesis becomes designed functional prototype of UMTS network with various options for individual settings user equipment as well as fixed mobile networks nodes.

This Master’s thesis is focused on the recent 3G mobile networks. The first chapter describes an evolution of standardization 3G and surveys a gradual development of 3G networks in Czech Republic from a point of view of commercially launched technologies and assigned frequency spectrums for single mobile operators. UMTS and CDMA 2000 are briefly approached in next subchapters. The subchapter CDMA 2000 is briefly concentrated on architecture and a physical layer of this technology and characterizes main features of four revises of developmental branch CDMA 2000 1x EV-DO. The subchapter UMTS is especially focused on a comparison of air interfaces TD-CDMA and W-CDMA. New features were implemented to the recent system UMTS for a better support of real-time services. These features increasing a throughput and decreasing a delay are described in a chapter Technology HSPA. This chapter chooses the most important features and describes changes (in a control and architecture) which had to be implemented. First chapter is finished by technology WiMAX. The most recent perspective cell systems are compared with WiMAX in this subchapter and qualitative parameters of WiMAX are shown there. The three different 3G technologies (UMTS-FDD, UMTS-TDD and CDMA 2000) are lunched in Czech Republic. The second chapter briefly compares coverage of three czech mobile operators (Telefónica O2, T-Mobile and U:fon) and then presents results of qualitative parameters of used 3G technologies. The simulation conducted by software IxChariot were focused on to gauge parameters like throughput, delay, jitter, lost data, MLR and DF. The conditions for providing real-time services were specified based on simulations that were practically checked. The lab composed in last chapter should bring closer to students technology UMTS-TDD launched by T-Mobile. The students will measure the qualitative parameters of this technology with the assistance of commonly available tools.

This work deals with the Universal Mobile Telecommunications System problems. It researches the parameters of influencing the UMTS Terrestrial Radio Access Network behaviour where is the Quality of Services support necessary. The aim of this master’s thesis is the simulation and evaluation of scenarios running real-time UMTS services in Opnet Modeler environment. In the first part is the short introduction to this technology problem. The requirements and the aims, the frequency plan, the network architecture and the Quality of Services support in UMTS are described. Creating the mobile network in the OPNET Modeler environment, configuration of the particular elements with the correct functionality and finally the parameters configuration for the Quality of Service at all workstations was the practical part of this work. At last phase was needed to compare the final statistics of the model without QoS support and the model with QoS support. I verified my knowledge in the OPNET Modeler program and the expected simulation results were confirmed. The final part of the thesis was creating the laboratory problem on the basis experience gained.

Diplomová práce je psána v angličtině a věnuje se standardu IEEE 802.11e, obsahujícím podporu kvality služeb a taky pojednává o kvalitě služeb QoS (Quality of Service) v systému UMTS. Rozebrány jsou hlavní teoretické pilíře daných mechanizmů a praktická část se zabývá simulacemi síťových modelů. Standard 802.11e objasňuje propojení vrstev na fyzické úrovni a zmiňuje metody přístupu k přenosovému médiu DCF, PCF, HCF, EDCA, HCCA. Dále přístupové kategorie a také odlišnosti v MAC podvrstvě, je rozebrána problematika při přenosu prioritních dat na základě identifikátorů. Vzpomenuta je taky struktura formátu rámce a techniky s rozprostřeným spektrem. Časové limity pro doručení prioritních dat a požadavky kladené na tyto data je možné snadno srovnat v tabulkách. Problematika kvality služeb je velice komplexní záležitost, nicméně jsou rozebrány základní klíčové parametry jako koncové zpoždění, jitter, zahazování dat, propustnost, velikost front a hodnota MOS. Zmíněny jsou i mechanizmy integrovaných RSVP a diferencovaných služeb pro zajištění QoS. U systému třetí generace UMTS je objasněna architektura a společná kooperace se systémem GSM. Vzájemné propojení obou sítí je zřejmé z obrázků. Zvýšený zájem je věnován vrstvovému modelu a funkcím RRM pro zajištění QoS. Objasněny jsou různé druhy předávání hovorů, tzv. Handover Control a funkce Admission Control. Rozebrány jsou jednotlivé třídy provozu Conversational, Streaming, Interactive a Background. Praktická část se odehrává v simulačním prostředí programu OPNET Modeler. Byly vytvořeny dva modely s různými scénáři pro srovnání zajištění QoS. Model objasňující princip standardu IEEE 802.11e obsahuje dvě bezdrátové sítě s přístupovými body a stanicemi, na kterých jsou sledovány simulace s různým zatížením přenášených dat. Pro porovnání výsledků je zkoumán rozdíl při použití metody HCF v síti s podporou QoS. Model UMTS sítě obsahuje základnové stanice Node B s možností vysílání do tří sektorů. Mobilní účastník pohybující se po trajektorii představuje princip funkce Softer Handover. Konfrontace mezi scénáři je zastoupena kompresí záhlaví pomocí funkce PDCP a rozlišení Type of Service. Obzvláště je sledováno chování prioritních dat hlasu a videa u obou sítí. Naměřená data zastupují grafy a průběhy výsledních charakteristik. Analýza diskutuje odlišnosti u sítě bez podpory a s podporou kvality služeb. Rozdíly jsou porovnány a vyhodnoceny dle metodiky QoS. Součástí práce je i řešení problémů při návrhu UMTS sítě a podány jsou taky užitečné tipy a návrhy na jejich odstranění. Projekty v simulačním softwaru jsou popsány dle postupu vyhotovení, avšak hloubka podrobností je potlačena. Detaily nejsou rozebírány, protože se očekává pokročilá znalost mechanizmů a jistá dávka zkušeností s programem.

This master's thesis deals with the issue of the security of GSM and UMTS mobile communication systems. In the thesis the principles of the authentication and encryption of both the mobile systems are described. Further, the constituent algorithms used for identity verification, key generation and encryption are mentioned. The commonly used algorithms are described along with their weaknesses. In the following part of this thesis, well-known attacks on GSM system are mentioned. In the part where UMTS system is dealt with one can find the algorithms used in this system to increase the security of transmitted data and authentication in comparison with GSM system. Therefore the whole process of authentication and encryption is described separately. In the last part the creation of programming models of authentication and encryption in GSM and encryption in UMTS is described. These models are created in the environment of Matlab version 2009b.

The purpose of this thesis is to show up possibilities of inter-vehicle communication and to introduce new approaches in communication for the purpose of enhancing the security and the fluency of vehicle transportation. This thesis also highlights vulnerabilities in communication. The main goal is the analysis of existing technology and the design of protocol for data transfer with focus on minimizing handover time of informations. Part of the design is a simulation of communication based on acquired information.