Hydrogen has been identified as a potential energy carrier due to its high energy capacity and environmental harmlessness. Compared with hydrogen production from hydrocarbons such as methane and naphtha in a conventional hydrogen energy system, photocatalytic hydrogen evolution from water splitting offers a more economic approach since it utilizes the abundant solar irradiation as energy source and water as initial reactant. Powder photocatalyst, which generates electrons and holes under illumination, is the origin where the overall reaction happens. High solar energy conversion efficiency especially from visible range is commonly the target. Besides, cocatalyst for hydrogen and oxygen evolution is also playing an essential role in facilitating the charge separation and enhancing the kinetics. In this thesis, the objective is to achieve high energy conversion efficiency towards water splitting from diverse aspects. The third chapter focuses on a controllable method to fabricate metal pattern, which is candidate for hydrogen evolution cocatalyst while chapter 4 is on the combination of strontium titanium oxide (SrTiO3) with graphene oxide (GO) for a better photocatalytic performance. In the last chapter, photoelectrochemical water splitting by Ta3N5 photoanode and FeOOH as a novel oxygen evolution cocatalyst has been investigated.

The role of high doping levels and the interfacial structure on the junction behavior between n-type silicon microwires and the conducting polymer, PEDOT:PSS, was investigated using tungsten probes, an established technique for Ohmic contact to individual microwires. The resistance and the doping density of carriers as a function of length along each microwire as well as the junction resistance between individual microwires and the conducting polymer were characterized by making Ohmic contact to microwires. The junction between highly-doped n-Si microwires and the conducting polymer had relatively symmetric current-voltage characteristics and a significantly lower junction resistance as compared to low-doped microwires. The current-voltage response of junctions formed between the polymer and low-doped microwires, which still incorporated the metal catalyst used in the growth process, was also studied. Junctions incorporating copper at the interface had similar current-voltage characteristics to those observed for the highly-doped microwire, while junctions incorporating gold exhibited significantly lower resistances

Photoelectrochemical (PEC) water splitting, using sunlight and appropriate semiconductors to produce hydrogen (H2) fuel, is a promising route to solve both the production of clean H2 fuel and storage for solar energy. Owing to its various advantages, hematite (α-Fe2O3) has emerged as a promising photoanode material for PEC water splitting. However, its poor electrical conductivity, low carrier mobility, short-hole diffusion length, and fast recombination rates of the electron-hole pairs have greatly limited its full potential for PEC performance. One way to improve the PEC activity of α-Fe2O3 is by doping with other elements. In particular, surface doping is proved to be more beneficial than bulk doping because it reduces the distance moved by the charge carriers from inside the bulk to the surface where they are required for interfacial transfer. In this study first-principles calculations based on density functional theory (DFT) were carried out to investigate the influence of Cu, Zn, Ti and Zr on the {0001} and {01 2} hematite surfaces for enhanced PEC water splitting. Various surfaces of hematite were constructed and their thermodynamic stabilities were determined by calculating surface and formation energies. The {0001} and {01 2} surfaces were found to be the most stable. Besides, all the doped systems were found thermodynamically stable. Furthermore, it was found that Cu doped surface systems does not only decrease the bandgap but also leads to the correct conduction band alignment for spontaneous water splitting. In all calculations, the charge density difference plots and the Bader charge analysis showed accumulation of charge at the top outmost surface, implying the photogenerated charge carriers can efficiently diffuse to the surface for enhanced interfacial charge transfer to the adsorbates. Morever, it was found that even with mono doping of Zn on the topmost layer of the {0001} α-Fe2O3 surface, the bandgap can be decreased without impurity states in the band structure which normally acts as recombination centres. Furthermore, the energetic stability and electronic properties of bimetallic doped {0001} α-Fe2O3 surface with (Zn, Ti) and (Zn, Zr) pairs for enhanced PEC water splitting was also studied. Bimetallic doping is viewed as an important and executable way of not only increasing the conductivity of a semiconductor material but also reducing the quick recombination of the electron-hole pairs. The doped systems showed negative formation energies under both O-rich and Fe-rich conditions implying that they are thermodynamically stable and could be prepared experimentally. Additionally, bimetallic doping of (Zn, Ti) and (Zn, Zr) on the {0001} surface is expected to enhance the PEC performance of α-Fe2O3 because Ti or Zr is capable of increasing the conductivity of α-Fe2O3 due to the substitution of Fe3+ with Ti4+ or Zr4+, while Zn can foster the surface reaction and reduce quick recombination of the electron-hole pairs. We hope that our results provided here will be of great interest to both experimental and theoretical researchers. / Thesis (PhD (Physics))--Univesity of Pretoria, 2020. / Ministry of Higher Education, Copperbelt University, Zambia / The University of Pretoria, Department of Physics / Centre for High-Performance Computer (CHPC), Cape Town / Physics / PhD (Physics) / Restricted

In this dissertation, α-Fe2O3 thin film deposition techniques were first evaluated to understand their effects on the structural, optical and photoelectrochemical (PEC) properties of the films. α-Fe2O3 films were deposited by dip, spin and combined dip/spin coating techniques on fluorine-doped tin oxide (FTO) substrates at an annealing temperature of 500°C. Structural properties suggest better crystallinity for films prepared by dip and combined dip/spin coating techniques as compared to spin coated films. Field emission scanning electron microscopy showed spherical nanoparticles with some agglomeration into small larvae-shape nanostructures for all the films. All films absorb in the visible region due to their bandgap of 1.98 ± 0.03 eV. Maximum photocurrent densities of 34.6, 7.8, and 13.5 µA/cm2 were obtained at 1.23 V vs reversible hydrogen electrode (RHE) for dip, spin and combined dip/spin coated films with the thickness of 740-800 ± 30 nm respectively. Improved crystallization, low charge transfer resistance at the solid/electrolyte junction, high surface states capacitance, and a more negative flat band potential values obtained for dip coated films using electrochemical techniques, have been associated to their improved photocurrent response. Furthermore, the annealing approach for preparing multi-layered α-Fe2O3 films using the dip coating technique was modified to enhanced their PEC performance. The first three layers of the films were annealed at 500°C and the fourth layer at 500, 600, 700, 750 and 800°C respectively. Films annealed at 750°C recorded the best performance, producing 0.19 mA/cm2 photocurrent at 1.23 V vs RHE; 5.3 times more than what was recorded for films sintered at 500°C, and the onset potential yielded a cathodic shift of 300 mV. The enhanced performance was linked to improved crystallization and absorption coefficient, lowered flat band potential, increased charge carrier density, decreased charge transfer resistance at the solid/liquid interface and increased surface states capacitance for films annealed at 750°C. Also, nanostructured heterojunction of α-Fe2O3 and porous copper (II) oxide (CuO) composites represented as α-Fe2O3/CuO was prepared for the enhancement of PEC water splitting. Structural studies confirmed the high purity of α-Fe2O3/CuO heterostructures produced. Enhanced photocurrent density of 0.53 mA/cm2 at 1.0 V vs RHE was achieved for α-Fe2O3/CuO photoanodes, representing a 19-fold increase compared to the value recorded for α-Fe2O3. The formation of a heterojunction coupled with the porous surface morphology of α-Fe2O3/CuO facilitated charge separation of photogenerated electron-hole pairs, reduced the bandgap and increased the charge carrier density of the heterostructure, enhancing PEC water splitting. / Thesis (PhD (Physics))--University of Pretoria, 2021. / National Research Foundation - The World Academy of Sciences (NRF) grant #110814 and South African Research Chairs Initiative (SARCHI) grant #115463. / Physics / PhD (Physics) / Restricted

Thesis advisor: Dunwei Wang / Due to the increasing energy demand from human activities, efficient utilization of renewable energy, such as wind, solar and geothermal energies, becomes necessary and urgent. Photoelectrochemical water splitting offers a great example to convert solar energy and storage it in the term of chemical bond. Seeking suitable photoanode materials becomes the research focus of my study, because the development of photoanode materials significantly lags that of robust photocathode (such as Si). The main challenge is to fabricate an efficient and stable photoanode material which can deliver high photocurrent and sufficient photovoltage which can match well with those of photocathode when made into tandem cell configuration. Hematite (α-Fe2O3) represents a promising metal oxide photoanode material, with a suitable band gap (2.1 eV), low cost and toxicity. Applying nanostructures and appropriate surface modification layers help address existing research challenges. As a result, a much lower turn on potential and greater photocurrent density is achieved. Another photoanode material attracts our attention is tantalum nitride (Ta3N5), with a similar band gap to hematite but much better light absorption properties, shows a poor stability in aqueous electrolyte. For both photoanode materials, thermodynamic and kinetic aspects are studied in details when tested in water splitting devices. These works provide new ideas and insights on the future studies. / Thesis (PhD) — Boston College, 2015. / Submitted to: Boston College. Graduate School of Arts and Sciences. / Discipline: Chemistry.

Metal oxide materials could offer earth-abundant, non-toxic alternatives to existing lightabsorber materials in thin-film photovoltaic and photoelectrochemical cells. However, efficiency of these devices based on existing metal oxides is typically low due to poor material properties. In this research, novel Sb:SnO2 nanorod and nanotube electron collectors have been synthesized, investigated and were used to improve the photo-conversion efficiency of top-performing BiVO4 photoelectrochemical cell. The performance of Sb:SnO2/BiVO4 photoanode achieved a new record for the product of light absorption and charge separation efficiencies (ηabs × ηsep) of ~ 57.3% and 58.5% under front- and back-side illumination at 0.6 VRHE and Sb:SnO2/BiVO4 PV cell achieved 1.22% solar power conversion efficiency. In addition, a new promising metal oxide material (CuBiW2O8) has been synthesized and its optoelectronic properties have been investigated to make photovoltaic cell which has potential to achieve over 30% solar power conversion efficiency.

Photoelectrochemical studies were performed on bismuth vanadate (BiVO₄) to understand chemical and physical properties of the photocatalysts, and to improve the photoactivity for water oxidation. Scanning electrochemical microscopy (SECM) was used to screen various dopants for BiVO₄, to calculate the photoconversion efficiencies to chemical energy at BiVO₄ electrodes, and to study the water oxidation intermediate radicals at the surface of BiVO₄. Tungsten and molybdenum doped BiVO₄ (W/Mo-BiVO₄) shows a photocurrent for water oxidation that is more than 10 times higher than undoped BiVO₄. Photoelectrochemical measurements and material analysis were done to discuss the factors that affect performance of BiVO₄. Finite elements analysis was also performed to explain the electron-hole transport and electrochemical reactions at W/Mo-BiVO₄ electrodes in solutions. Addition of conductive or electron accepting materials, e.g. reduced graphene oxide, into BiVO₄ was tried to study the electron-hole transport phenomena in the metal oxide electrodes. Surface adsorbed radicals produced during the water oxidation at W/Mo-BiVO₄ were interrogated by using SECM that the surface coverage and decay kinetics of adsorbed hydroxyl radicals at W/Mo-BiVO₄ were measured. The quantum efficiencies of the injected photon conversion to chemical energy were obtained from the photoelectrochemical measurements by using SECM. SECM techniques and finite elements analysis were also used to measure the faradaic efficiency of water oxidation at W/Mo-BiVO₄ under irradiation. Finally, unbiased water splitting to generate hydrogen and oxygen from water splitting only using photon energy at W/Mo-BiVO₄ electrodes was demonstrated in a dual n-type semiconductor or Z-scheme device. / text

While prices of solar energy are becoming cost competitive with traditional fossil fuel resources, large scale deployment of solar energy has been limited by the inability to store excess electrical energy efficiently. One promising route towards both the capture and storage of solar energy is through photoelectrochemical water splitting, a process by which a semiconducting material can collect energy from the sun and use it to directly split water (H2O) into hydrogen fuel and oxygen. Unfortunately, photoelectrochemical water splitting devices are limited by the low efficiencies and high overpotentials of the oxygen evolution reaction (OER). To improve kinetics of OER, different electrocatalyst are often coated on the semiconductor. However, the role of the catalyst and the mechanism of charge transfer at the semiconductor|catalyst interface is not clear. It is important to understand this interface if we are to rationally design high performance water splitting cells. The research presented in this dissertation takes on two aims: 1) obtaining a fundamental knowledge of the charge transfer processes that take place at the semiconductor catalyst interface of photoanodes and 2) developing new experimental approaches that can be applied towards achieving the first aim. Specifically, this dissertation begins with a prospectus that outlines the state of the field, and the what was known about the semiconductor|electrocatalyst interface at the outset of the presented work (Chapter II). Next, the testing and application of new nanoelectrode AFM probes to study an array of electrochemical phenomena will be discussed (Chapter III). These probes will then be applied towards the study of hematite (Fe2O3) semiconductors coated with cobalt phosphate (oxy)hydroxide (CoPi) electrocatalyst (Chapter IV) and bismuth vanadate (BiVO4) semiconductors coated with CoPi electrocatalyst (Chapter 5). This dissertation includes previously published and unpublished co-authored material. / 2020-01-11

This thesis presents an integrated study of nanocatalysts for heterogenous catalytic and electrochemical processes using pure ruthenium (Ru) with mixed-phase and platinum-based nanomaterials synthesized by continuous-flow chemistry. There are three major challenges to the application of nanomaterials in heterogenous catalytic reactions and electrocatalytic processes in acidic solution. These challenges are the following: (i) controlling the size, shape and crystallography of nanoparticles to give the best catalytic properties, (ii) scaling these nanoparticles up to a commercial quantity (kg per day) and (iii) making stable nanoparticles that can be used catalytically without degrading in acidic electrolytes. Some crucial limitations of these nanostructured materials in energy conversion and storage applications were overcome by continuous-flow chemistry. By using a continuous-flow reactor, the creation of scalable nanoparticle systems was achieved and their functionality was modified to control the nanoparticles’ physical and chemical characteristics. The nanoparticles were also tested for long-term stability, to make sure these nanoparticles were feasible under realistic working conditions. These nanoparticles are (1) shape- and crystallography-controlled ruthenium (Ru) nanoparticles, (2) size-controlled platinum-metal (Pt-M= nickel (Ni) & copper (Cu)) nanooctahedra (while maintaining morphology) and (3) core-shell platinum@ruthenium (Pt@Ru) nanoparticles where an ultrathin ruthenium shell was templated onto the platinum core. Thus, a complete experimental validation of the formation of a scalable amount of these nanoparticles and their catalytic activity and stability towards the oxygen evolution reaction (OER) in acid medium, hydrolysis of ammonia borane (AB) along with plausible explanations were provided.

The energy consumptions worldwide have increased simultaneously with the growth of the population and of the economy. Nowadays, finding an alternative way to satisfy the energy demand is one of the great challenges for the future of humanity, especially due to the limitation of fossil fuels and their effect on global warming. Hydrogen, as an alternative fuel for the future, is very attractive. Compared to traditional methods, such as the steam reforming of natural gas or coal gasification, photocatalytic water splitting (PWS) is considered to be the most sustainable alternative for producing hydrogen as a future fuel. PWS usually relies on semiconductor material that can transform the absorbed solar photon into photogenerated electrons and holes, creating a photopotential which can drive the electrochemical production of molecular hydrogen from the reduction of water. Despite its promising application, semiconductor-based PWS usually suffers from low carrier mobility and short diffusion length. Furthermore, the recombination of photogenerated electrons and holes might occur, especially if there are no suitable reaction sites available on the surface of the semiconductor. In order to facilitate the catalytic reactions on the surface of the semiconductor, the presence of a cocatalyst is necessary in order to obtain more efficient PWS processes. To this day, noble metals such as Pt, Pd, RuO2 and IrO2 are still the benchmark cocatalysts for PWS. Nevertheless, due to their high cost and limited supply, it is mandatory to develop a suitable strategy and to identify more efficient materials. Therefore, within the framework of this dissertation, novel cocatalysts and strategies that can improve the efficiency of the photocatalytic water splitting processes have been developed. Firstly, we developed a cocatalyst combining noble metals and semiconductors by means of partial galvanic replacement of the Cu2O nanocrystal with Au. The deposition of this cocatalyst on TiO2 was studied for the photocatalytic H2 production in order to explore the synergistic effect of the plasmonic resonance from the Au nanoparticles and pn-junction between Cu2O and TiO2. Additionally, the plasmonic effect of the Au films was also studied and utilized in order to improve the PWS. Secondly, the nanoscaling of cocatalysts was studied in order to improve the efficiency thereof and to reduce the cost of the cocatalyst materials. Moreover, it is sought to explore the quantum size effect on the properties of the cocatalyst and their effect on the photocatalytic reaction. Atomically precise Au and Ni nanoclusters were employed in these studies. Au nanoclusters were studied in relation to the cocatalysts in the photocatalytic water splitting, and Ni nanoclusters were studied in relation to the cocatalysts in the electrocatalytic water oxidation. The results of these studies will provide new insights in relation to the strategy used in order to develop efficient cocatalysts for the purpose of photocatalytic water splitting.