The role of high doping levels and the interfacial structure on the junction behavior between n-type silicon microwires and the conducting polymer, PEDOT:PSS, was investigated using tungsten probes, an established technique for Ohmic contact to individual microwires. The resistance and the doping density of carriers as a function of length along each microwire as well as the junction resistance between individual microwires and the conducting polymer were characterized by making Ohmic contact to microwires. The junction between highly-doped n-Si microwires and the conducting polymer had relatively symmetric current-voltage characteristics and a significantly lower junction resistance as compared to low-doped microwires. The current-voltage response of junctions formed between the polymer and low-doped microwires, which still incorporated the metal catalyst used in the growth process, was also studied. Junctions incorporating copper at the interface had similar current-voltage characteristics to those observed for the highly-doped microwire, while junctions incorporating gold exhibited significantly lower resistances

While prices of solar energy are becoming cost competitive with traditional fossil fuel resources, large scale deployment of solar energy has been limited by the inability to store excess electrical energy efficiently. One promising route towards both the capture and storage of solar energy is through photoelectrochemical water splitting, a process by which a semiconducting material can collect energy from the sun and use it to directly split water (H2O) into hydrogen fuel and oxygen. Unfortunately, photoelectrochemical water splitting devices are limited by the low efficiencies and high overpotentials of the oxygen evolution reaction (OER). To improve kinetics of OER, different electrocatalyst are often coated on the semiconductor. However, the role of the catalyst and the mechanism of charge transfer at the semiconductor|catalyst interface is not clear. It is important to understand this interface if we are to rationally design high performance water splitting cells. The research presented in this dissertation takes on two aims: 1) obtaining a fundamental knowledge of the charge transfer processes that take place at the semiconductor catalyst interface of photoanodes and 2) developing new experimental approaches that can be applied towards achieving the first aim. Specifically, this dissertation begins with a prospectus that outlines the state of the field, and the what was known about the semiconductor|electrocatalyst interface at the outset of the presented work (Chapter II). Next, the testing and application of new nanoelectrode AFM probes to study an array of electrochemical phenomena will be discussed (Chapter III). These probes will then be applied towards the study of hematite (Fe2O3) semiconductors coated with cobalt phosphate (oxy)hydroxide (CoPi) electrocatalyst (Chapter IV) and bismuth vanadate (BiVO4) semiconductors coated with CoPi electrocatalyst (Chapter 5). This dissertation includes previously published and unpublished co-authored material. / 2020-01-11

Thesis advisor: Dunwei Wang / Water splitting has been recognized as a promising solution to challenges associated with the intermittent nature of solar energy for over four decades. A great deal of research has been done to develop high efficient and cost-effective catalysts for this process. Among which tantalum nitride (Ta₃N₅) has been considered as a promising candidate to serve as a good catalyst for solar water splitting based on its suitable band structure, chemical stability and high theoretical efficiency. However, this semiconductor is suffered from its special self-oxidation problem under photoelectrochemical water splitting conditions. Several key unique properties of graphitic carbon nitride (g-C₃N₄) render it an ideal choice for the protection of Ta₃N₅. In this work, Ta₃N₅/g-C₃N₄ hybrid photoanode was successfully synthesized. After addition of co-catalyst, the solar water splitting performance of this hybrid photoanode was enhanced. And this protection method could also act as a potential general protection strategy for other unstable semiconductors. / Thesis (MS) — Boston College, 2018. / Submitted to: Boston College. Graduate School of Arts and Sciences. / Discipline: Chemistry.

Anthropogenic climate change presents an unrivalled threat to environmental stability and the prosperity of future generations. Utilising abundant, renewable resources in energy generation and storage will be essential to halt climate change and its effects. Solar water splitting is an excellent tool in the renewable energy arsenal for countering climate change, as it utilises both sunlight and water, two of the most abundant resources available on earth. Furthermore, the direct formation of a chemical fuel, hydrogen, is thought to be more practical for storing in large quantities than electricity. Work in this thesis covers the investigation of a variety of materials, fabricated by aerosol assisted chemical vapour deposition (AACVD), for their ability to carry out photoelectrochemical water splitting. In one project, thin films of Bi2Ti2O7 (BTO), specifically of the pyrochlore crystal structure, are fabricated by AACVD and analysed for their photoelectrochemical properties. The resulting thin films are found to be phase pure with a band gap of 2.88 eV, which is 0.32 eV smaller than TiO2. Efforts to dope the BTO thin films are further investigated through the addition of iron. Significant modification to the band gap is observed, leading to a confirmed pyrochlore thin film exhibiting a band gap of 2.5 eV, a reduction of 0.38 eV from undoped BTO. The resulting thin film had a photocurrent 5 times higher than that of undoped BTO. Finally, efforts to fabricate Fe2Ti2O7 are outlined. It is discovered that a stable phase of Fe2TiO5 is preferentially formed over the pyrochlore phase, even with dramatic modification to the deposition parameters and precursor stoichiometry. The high stability of this phase, coupled with the limiting features of the glass substrates, highlights the challenges with forming certain pyrochlore thin films. In a second project, the effect of depositing titanium nanoclusters onto the surface of bismuth vanadate is investigated. Nanoclusters are of huge interest because their properties lie between those of atoms and bulk materials. Additionally, nanoscale clusters can be fabricated with incredible precision, allowing one to select discrete diameter particles for deposition on surfaces. Ti nanoclusters over a range of sizes are deposited onto BiVO4 photoanodes. It is discovered that the deposition of ultralow loadings of Ti2000 clusters results in an 80 % enhancement in the photocurrent of the BiVO4 substrates. Further experimentation highlights that the photocurrent enhancement is linked to the size of the nanocluster and the density of the clusters on the surface. A mechanism is outlined, whereby the Ti nanoclusters partially reduce the surface of the BiVO4, leading to enhanced electron transport within the thin films due to the presence of oxygen vacancies. In a final project, polycrystalline InN, GaN and systematically controlled InxGa1-xN composite thin films are fabricated on FTO glass by a facile, low-cost and scalable aerosol assisted chemical vapor deposition technique. Variation of the indium content in the composite films leads to a dramatic shift in the optical absorbance properties, which correlates with the band edges shifting between those of GaN to InN. Moreover, the photoelectrochemical properties are shown to vary with indium content, with the 50 % indium composite having an external quantum efficiency of around 8 %. Whilst the overall photocurrent is found to be low, the photocurrent stability is shown to be excellent, with little degradation seen over 1 hour. Subsequent attempts to modify the morphology by conducting vertical-AACVD are also outlined. Thin films fabricated using vertical-AACVD are found to grow via a different mechanism, leading to undesired split phase growth, where two different compositions form on the same substrate.

Thesis advisor: Dunwei Wang / Solar energy, the most abundant and free renewable energy, holds great promise for humanity's sustainable development. How to efficiently and inexpensively capture, covert solar energy and store it for off peak usages constitutes a grand challenge for the scientific community. Photovoltaic devices are promising candidates but are too costly to be implemented in large scales. On a fundamental level, this is due to the dilemma that the length scales of the optical pathways and electrical pathways often do not match within the photovoltaic device materials. Consider traditional Si solar cell as an example, effective light absorption requires up to hundreds of microns material while the photogenerated charge carries can only diffuse less than a few microns or even shorter before recombination. Such a problem may be solved by using Si nanowires (SiNWs) because vertically aligned nanowires can orthogonalize the light absorption and charge carrier collection pathways, thereby enabling the use of low-cost materials for practically appealing solar energy conversion devices. The objective of this thesis work is to explore low-cost synthesis of vertically aligned SiNW arrays and study their performance in both solar energy conversion and storage devices. We developed a method to synthesize vertically aligned SiNW arrays in a hot-wall chemical vapor deposition system with tunable length, doping level, and diameter for systematical studies. Empowered by the synthetic control, various types of vertical SiNW arrays were characterized by both steady-state (photoelectrochemical measurement) and transient (electrochemical impedance spectroscopy) techniques in a photoelectrochemical cell platform. Additionally, SiNWs were demonstrated to be a promising candidate for photoelectrochemical aromatic ketone reduction and CO₂ fixation. The reactions studied in this thesis are in close resemblance to natural photosynthesis and the resulted product molecules are precursors to nonsteroidal anti-inflammatory drugs, ibuprofen and naproxen. Lastly, vertical transparent conductive oxide nanotubes were prepared from vertical SiNW array templates. Ultrathin hematite (Fe₂O₃) film was coated on the nanotube scaffold by atomic layer deposition to form a heteronanostructure photoelectrode for efficient solar water oxidation. Our results highlight the potential of vertically aligned SiNW arrays in solar cell, solar water splitting and artificial photosynthesis applications. / Thesis (PhD) — Boston College, 2012. / Submitted to: Boston College. Graduate School of Arts and Sciences. / Discipline: Chemistry.

The increasing demand for energy and the pressure to reduce reliance on fossil fuels encourages the development of devices to harness clean and renewable energy. Solar energy is a large enough source to fulfill these demands, however, in order to overcome its daily and seasonal variability, it has been proposed that sunlight be harvested and stored in the form of chemical fuels. One potential approach is the photosynthetic splitting of water to store solar energy in the simplest chemical bond, H–H, using a device that includes: semiconducting microwire arrays as light harvesting components, redox catalysts, and a membrane barrier for separating the products of water redox reactions.. However, the harvested solar energy can be lost across the system and it is critical to characterize the electrical properties of each component within the system to quantify how much of this energy will ultimately be coupled to the water splitting reactions. The aim of this research is to develop approaches for characterization of a proposed system of this kind, incorporating individual semiconductor microwires as photoelectrodes (with no redox catalysts) embedded into a candidate conducting polymer membrane to form a single functional unit. Semiconductor microwires were isolated and using a novel contact formation approach with tungsten probes in a standard probe station, and their current versus voltage properties were characterized. This approach is of particular interest when ii considering the limitations of conventional contact formation approaches (e.g. thermal evaporation of contact metals), arising from the small dimensions of the microwires and also the incompatibility of these techniques with many microwire/polymer structures due to the unwanted interactions between polymers, photoresists, etchants and the high temperature lithographic processes. The electrical properties of different microwires and also the junctions between microwires and two candidate polymers were studied. Specifically, the combination of methyl-terminated silicon microwires and PEDOT:PSS:Nafion demonstrated promising behavior, with a total DC resistance of approximately 720 kΩ (i.e. losses < 16 mV at maximum available photocurrent), making it a suitable candidate for the use in the proposed system. The outcome of these research may be applied to many applications including semiconducting microstructures and conducting polymers.

The increasing demand for energy and the pressure to reduce reliance on fossil fuels encourages the development of devices to harness clean and renewable energy. Solar energy is a large enough source to fulfill these demands, however, in order to overcome its daily and seasonal variability, it has been proposed that sunlight be harvested and stored in the form of chemical fuels. One potential approach is the photosynthetic splitting of water to store solar energy in the simplest chemical bond, H–H, using a device that includes: semiconducting microwire arrays as light harvesting components, redox catalysts, and a membrane barrier for separating the products of water redox reactions.. However, the harvested solar energy can be lost across the system and it is critical to characterize the electrical properties of each component within the system to quantify how much of this energy will ultimately be coupled to the water splitting reactions. The aim of this research is to develop approaches for characterization of a proposed system of this kind, incorporating individual semiconductor microwires as photoelectrodes (with no redox catalysts) embedded into a candidate conducting polymer membrane to form a single functional unit. Semiconductor microwires were isolated and using a novel contact formation approach with tungsten probes in a standard probe station, and their current versus voltage properties were characterized. This approach is of particular interest when ii considering the limitations of conventional contact formation approaches (e.g. thermal evaporation of contact metals), arising from the small dimensions of the microwires and also the incompatibility of these techniques with many microwire/polymer structures due to the unwanted interactions between polymers, photoresists, etchants and the high temperature lithographic processes. The electrical properties of different microwires and also the junctions between microwires and two candidate polymers were studied. Specifically, the combination of methyl-terminated silicon microwires and PEDOT:PSS:Nafion demonstrated promising behavior, with a total DC resistance of approximately 720 kΩ (i.e. losses < 16 mV at maximum available photocurrent), making it a suitable candidate for the use in the proposed system. The outcome of these research may be applied to many applications including semiconducting microstructures and conducting polymers.

This thesis describes studies of materials which can be exploited for hydrogen production from water and sunlight. The materials investigated are maghemite (γ-Fe2O3), magnetite (Fe3O4) and especially hematite (α-Fe2O3), which is an iron oxide with most promising properties in this field. Hematite has been deposited using Atomic Layer Deposition (ALD) - a thin-film technique facilitating layer-by-layer growth with excellent thickness control and step coverage. The iron oxides were deposited using bis-cyclopentadienyl iron (Fe(Cp)2) or iron pentacarbonyl (Fe(CO)5) in combination with an O2 precursor. Since it is crucial to have good control of the deposition process, the influence of substrate, process temperature, precursor and carrier gas have been investigated systematically. By careful control of these deposition parameters, three polymorphs of iron oxide could be deposited: hematite (α-Fe2O3), maghemite (γ-Fe2O3) and magnetite (Fe3O4). The deposited materials were characterized using X-ray Diffraction, Raman and UV-VIS Spectroscopy, and Scanning Electron Microscopy. Hard X-ray Photoelectron Spectroscopy (HAXPES) was also used, since it is a non-destructive, chemically specific, surface sensitive technique – the surface sensitivity resulting from the short mean escape depth of the photoelectrons. The depth probed can be controlled by varying the excitation energy; higher photoelectron energies increasing the inelastic mean-free-path in the material. HAXPES studies of atomic diffusion from F-doped SnO2 substrates showed increased doping levels of Sn, Si and F in the deposited films. Diffusion from the substrate was detected at annealing temperatures between 550 °C and 800 °C. Films annealed in air exhibited improved photocatalytic behavior; a photocurrent of 0.23 mA/cm2 was observed for those films, while the as-deposited hematite films showed no photo-activity whatsoever. The optical properties of low-dimensional hematite were studied in a series of ultra-thin films (thicknesses in the 2-70 nm range). The absorption maxima were shifted to higher energies for films thinner than 20 nm, revealing a different electronic structure in thin films.

Materials and device concepts for renewable solar hydrogen production, and size dependent properties of ZnO quantum dots are the two main themes of this thesis. ZnO particles with diameters less than 10 nm, which are small enough for electronic quantum confinement, were synthesized by hydrolysis in alkaline zinc acetate solutions. Properties investigated include: the band gap - particle size relation, phonon quantum confinement, visible and UV-fluorescence as well as photocatalytic performance. In order to determine the absolute energetic position of the band edges and the position of trap levels involved in the visible fluorescence, methods based on combining linear sweep voltammetry and optical measurements were developed. The large band gap of ZnO prevents absorption of visible light, and in order to construct devices capable of utilizing a larger part of the solar spectrum, other materials were also investigated, like hematite , Fe2O3, and CIGS, CuIn1-xGaxSe2. The optical properties of hematite were investigated as a function of film thickness on films deposited by ALD. For films thinner than 20 nm, a blue shift was observed for both the absorption maximum, the indirect band gap as well as for the direct transitions. The probability for the indirect transition decreased substantially for thinner films due to a suppressed photon/phonon coupling. These effects decrease the visible absorption for films thin enough for effective charge transport in photocatalytic applications. CIGS was demonstrated to be a highly interesting material for solar hydrogen production. CIGS based photocathodes demonstrated high photocurrents for the hydrogen evolution half reaction. The electrode stability was problematic, but was solved by introducing a modular approach based on spatial separation of the basic functionalities in the device. To construct devices capable of driving the full reaction, the possibility to use cells interconnected in series as an alternative to tandem devices were investigated. A stable, monolithic device based on three CIGS cells interconnected in series, reaching beyond 10 % STH-efficiency, was finally demonstrated. With experimental support from the CIGS-devices, the entire process of solar hydrogen production was reviewed with respect to the underlying physical processes, with special focus on the similarities and differences between various device concepts.

L’objectif principal de ce travail de thèse était de mettre en évidence et de mesurer l’effet co-catalytique de complexes moléculaires organo-métalliques à base de métaux de transition adsorbés sur des semi-conducteurs dopés photo-actifs vis-à-vis des réactions de photo-dissociation de l’eau et de photo-réduction du dioxyde de carbone, en en vue d’applications dans des cellules photochimiques et photo-électrochimiques. Nous avons tout d’abord identifié et sélectionné les matériaux (deux semi-conducteurs photo-actifs et deux co-catalyseurs moléculaires électroactifs) les plus adaptés (les résultats sont présentés dans le chapitre I). Nous avons ensuite conçu, développé et mis au point un bâti expérimental permettant la détection et le dosage en continu des produits de réaction lors des réactions d’intérêt (les résultats sont présentés dans le chapitre II). La détection des produits de réaction se fait à l’aide d’un chromatographe en phase gazeuse couplé au réacteur. Nous avons ensuite élaboré/synthétisé et mesuré les propriétés intrinsèques des matériaux sélectionnés (les résultats sont présentés dans le chapitre III). Finalement, nous avons mis en évidence l’activité co-catalytique des complexes utilisés et mesuré un ensemble d’indicateurs de performance tels que les cinétiques de réaction et les fréquences de « turn-over » (les résultats sont présentés dans le chapitre IV). / The main objective of this research work was to put into evidence the co-catalytic effect of organo-metallic molecular complexes containing transition metals as reactive centers, adsorbed at the surface of doped semiconductors with photo-activity with regard to water photo-dissociation and carbon dioxide photo-reduction, in view of practical applications in photochemistry and photo-electrochemistry. First, appropriate materials (two photoactive semiconductors and two molecular co-catalysts) have been identified and selected (results are presented in chapter I). Then, we have designed, constructed and optimized a specific test bench that can be used for the continuous detection and titration of reaction products (results are presented in chapter II). Product analysis was achieved by coupling a gas-phase chromatograph to the photo-electrochemical reactor. Then, photoactive semiconductors and molecular co-catalysts have been elaborated/synthesized and their intrinsic properties have been measured (results are presented in chapter III). Finally, the co-catalytic activity of molecular complexes has been put into evidence and several performance indicators such as reaction kinetics and turn-over frequency have been measured (results are presented in chapter IV).