Flow instabilities occur at all scales in planetary systems. In this thesis we examine three cases of such instabilities, on three very different length scales. In the first part, we test the idea that Archean granite-greenstone belts (GGBs) form by crustal diapirism, or Rayleigh-Taylor instabilities. GGBs are characterized by large granitic domes (50-100 km in diameter) embedded in narrow keel-shaped greenstones. They are ubiquitous in Archean (> 2.5 Ga) terrains, but rare thereafter. We performed finite element calculations for a visco-elastic, temperature-dependent, non-Newtonian crust under conditions appropriate for the Archean, which show that dense low-viscosity volcanics overlying a felsic basement will overturn diapirically in as little as 10 Ma, displacing as much as 60 % of the volcanics to the lower crust. This surprisingly fast overturn rate suggests that diapiric overturn dominated crustal tectonics in the hot conditions of the Early Earth, becoming less important as the Earth cooled. Moreover, the deposition of large volumes of wet basaltic volcanics to the lower crust may provide the source for the formation of the distinctly Archean granitic rocks which dominate Earth's oldest continents. The second part examines the origin of Venusian coronae, circular volcanic features unique to Venus. Coronae are thought to result from small instabilities (diapirs) from the core-mantle boundary, which are typical of stagnant-lid convection. However, most young coronae are located in a region surrounded by long-lived hotspots, typical of a more active style of mantle convection. Using analogue experiments in corn syrup heated from below, we show that the co-existence of diapirs and long-lived mantle plumes are a direct consequence of the catastrophic overturn of the cold Venusian lithosphere thought to have occurred ~ 700 Ma ago. In the last part we analyze the thermal effect of fluid flow through a full-scale experiment testing clay and concrete tunnel seals in a Deep Geological Repository for nuclear was finite element software, we were able to show that the formation of fissures in the heated chamber between the two seals effectively limited heat flow, and could explain the discrepancy between the predicted and measured temperatures.

Master of Science / Department of Mechanical and Nuclear Engineering / William L. Dunn / A prototype system for detecting explosives at standoff distances, using a signature based radiation scanning approach, is being developed at Kansas State University. The prototype will incorporate both a machine x-ray source and a machine neutron source to generate signatures from unknown samples of material. These signatures can be compared to templates measured or calculated from known explosive samples using a figure-of-merit. The machine neutron source uses the fusion of deuterium and tritium to create 14.1 MeV neutrons. Due to its radioactivity, the tritium must be sealed within the system. A new method of controlling the gas pressure with the DT generator was developed using a Zr-V-Fe getter supplied by a commercial firm. The shielding and collimation of the 14.1 MeV neutron source is accomplished using layers of steel, high-density polyethylene and borated high-density polyethylene. This thesis describes the development of the gas control method for the sealed neutron source, design studies for the shielding and collimation of the neutron source and modifications made to the building in which the prototype is being housed.

Doctor of Philosophy / Department of Mechanical and Nuclear Engineering / Douglas S. McGregor / The microstructured semiconductor neutron detector (MSND) was investigated and previous designs were improved and optimized. In the present work, fabrication techniques have been refined and improved to produce three-dimensional microstructured semiconductor neutron detectors with reduced leakage current, reduced capacitance, highly anisotropic deep etched trenches, and increased signal-to-noise ratios. As a result of these improvements, new MSND detection systems function with better gamma-ray discrimination and are easier to fabricate than previous designs. In addition to the microstructured diode fabrication improvement, a superior batch processing backfill-method for 6LiF neutron reactive material, resulting in a nearly-solid backfill, was developed. This method incorporates a LiF nano-sizing process and a centrifugal batch process for backfilling the nanoparticle LiF material. To better transition the MSND detector to commercialization, the fabrication process was studied and enhanced to better facilitate low cost and batch process MSND production. The research and development of the MSND technology described in this work includes fabrication of variant microstructured diode designs, which have been simulated through MSND physics models to predict performance and neutron detection efficiency, and testing the operational performance of these designs in regards to neutron detection efficiency, gamma-ray rejection, and silicon fabrication methodology. The highest thermal-neutron detection efficiency reported to date for a solid-state semiconductor detector is presented in this work. MSNDs show excellent neutron to gamma-ray (n/γ) rejection ratios, which are on the order of 106, without significant loss in thermal-neutron detection efficiency. Individually, the MSND is intrinsically highly sensitive to thermal neutrons, but not extrinsically sensitive because of their small size. To improve upon this, individual MSNDs were tiled together into a 6x6-element array on a single silicon chip. Individual elements of the array were tested for thermal-neutron detection efficiency and for the n/γ reject ratio. Overall, because of the inadequacies and costs of other neutron detection systems, the MSND is the premier technology for many neutron detection applications.

Doctor of Philosophy / Mechanical and Nuclear Engineering / Douglas S. McGregor / There is a need for compact, rugged neutron detectors for a variety of applications including national security and oil well logging. A solid form neutron detector would have a higher efficiency than present day gas filled ³He and ¹⁰BF ₃ detectors, which are standards currently used in the industry today. A sub-branch of the III-V semiconductors is the filled tetrahedral compounds, known as Nowotny-Juza compounds (A[superscript I]B[superscript II]C[superscript V]). These materials are desirable for their cubic crystal structure and semiconducting electrical properties. Originally studied for photonic applications, Nowotny-Juza compounds have not been fully developed and characterized. Nowotny-Juza compounds are being studied as neutron detection materials here, and the following work is a study of LiZnP and LiZnAs material development and device characterization. Precursor binaries and ternary materials of LiZnAs and LiZnP were synthesized in-house in vacuum sealed quartz ampoules with a crucible lining. Synthesized powders were characterized by x-ray diffraction, where lattice constants of 5.751 ± .001 Å and 5.939 ± .002 Å for LiZnP and LiZnAs, respectively, were determined. A static vacuum sublimation in quartz was performed to help purify the synthesized ternary material. The resulting material from the sublimation process showed characteristics of a higher purity ternary compound. Bulk crystalline samples were grown from the purified material. Ingots up to 9.0 mm in diameter and 13.0 mm in length were harvested. Individual samples were characterized for crystallinity on a Bruker AXS Inc. D2 CRYSO, energy dispersive x-ray diffractometer, and a Bruker AXS D8 DISCOVER, high-resolution x-ray diffractometer with a 0.004° beam divergence. High-resolution XRD measurements indicated reasonable out-of-plane and in-plane ordering of LiZnP and LiZnAs crystals. Devices were fabricated from the LiZnP and LiZnAs crystals. Resistivity of devices were determined within the range of 10⁶ – 10¹¹ Ω cm. Charge carrier mobility and mean free drift time products were characterized for electrons at 8.0 x 10⁻⁴ cm² V⁻¹ ± 4.8% and 9.1 x 10⁻⁴ cm² V⁻¹ ± 4.4% for LiZnP and LiZnAs respectively. Sensitivity to 337 nm laser light (3.68 eV photons) was observed, where an absorption coefficient of 0.147 mm⁻¹ was determined for LiZnAs devices. Thermal neutron sensitivity was evaluated with unpurified and purified LiZnP and LiZnAs devices. Sensitivity was observed, however material quality and crystalline quality significantly hindered device performance.

The chemistry and corrosion mechanisms associated with reduced sulfur compounds such as calcium sulfide, present in ground granulated blast-furnace slag (GGBFS), have been studied in high-density concrete, mortar and simulated pore-water environments. The high-density concrete and mortar samples were produced to replicate the high-density GGBFS concrete, in the dry storage containers (DSCs), used for radiation shielding from used nuclear fuel. Electrochemical measurements on embedded steel electrodes in high-density GGBFS concrete and mortar samples, showed that sulfide is capable of consuming oxygen to create a stable, reducing environment, though not in all cases, and the high-frequency electrolyte resistance increases with hydration time. Ion chromatography on simulated pore-water environments determined that thiosulfate is quite kinetically stable as a sulfide oxidation product and magnetite is capable of oxidizing sulfide. Microscopy has also been used to provide visual evidence of GGBFS hydration and elemental quantification of the hydrating microstructure in different environments.

The chemistry and corrosion mechanisms associated with reduced sulfur compounds such as calcium sulfide, present in ground granulated blast-furnace slag (GGBFS), have been studied in high-density concrete, mortar and simulated pore-water environments. The high-density concrete and mortar samples were produced to replicate the high-density GGBFS concrete, in the dry storage containers (DSCs), used for radiation shielding from used nuclear fuel. Electrochemical measurements on embedded steel electrodes in high-density GGBFS concrete and mortar samples, showed that sulfide is capable of consuming oxygen to create a stable, reducing environment, though not in all cases, and the high-frequency electrolyte resistance increases with hydration time. Ion chromatography on simulated pore-water environments determined that thiosulfate is quite kinetically stable as a sulfide oxidation product and magnetite is capable of oxidizing sulfide. Microscopy has also been used to provide visual evidence of GGBFS hydration and elemental quantification of the hydrating microstructure in different environments.