Today, the air transport industry has become an essential element of global society by its great contributions to the wide exchanges of cultures/people and to the rapid growth in the world economy. However, on the other hand, the adverse impacts on the environment caused by air transport, such as air pollution, noise and climate change, are drawing, increasingly, growing public concern. In order to address the steady growth in air-travel demand in the next decades through an environmentally-friendly way and realise the ACARE 2020 environmental goals, The Clean Sky programme has been launched by European Union over the period 2008 – 2013. The project research, described in this thesis and sponsored by the Clean Sky programme, aims at evaluating the feasibility of reducing the environmental impact of commercial aviation through the introduction of changes in the aircraft operational rules and procedures, as well as the application of the new-generation propfan (open rotor) engine, based on flight trajectory multidisciplinary optimisation and analysis of commercial aircraft. In order to accomplish the above research objectives, a complete methodology to achieve and realise optimum flight trajectories has been initially proposed. Then, 12 component-level models which function as simulating different disciplines, such as aircraft performance, engine performance, engine gaseous emission, and flight noise, have been developed or selected/adopted. Further, nine system-level integration and optimisation models were built. These system-level models simulate flights from Amsterdam Schiphol airport in the Netherlands to Munich airport in Germany flown by different types of aircraft through different flight phases with different optimisation objectives. Finally, detailed investigations into the flight trajectory optimisations were performed, extensive optimisation results were achieved and corresponding description, analysis and comparisons were provided. The main contributions of this work to knowledge broadly comprise the following: 1) the further development regarding the methodology of flight trajectory multidisciplinary optimisation; 2) previous work on aircraft trajectory optimisation has often considered fixed objectives over the complete flight trajectory. This research focused on representative flight phases of a flight mission with different optimisation objectives, namely, noise impact and fuel burn during the departure phase; fuel burn and flight time during en route phase; and noise impact and NOx emission during the arrival phase; 3) this research has extended the current flight trajectory optimisations to turboprop and propfan equipped aircraft. As a result, a relative complete 2D flight trajectory multidisciplinary optimisation spectrum, spanned by primary commercial aircraft types, primary flight phases and primary optimisation objectives of interest, has been built. Although encouraging progress have been achieved, this project research, as with any other research activity, is also only ‘on the way’ rather than coming to the ‘end’ point. There are still many aspects which can be improved further and there is still much new research and exploration which can be investigated further. All these have also been suggested in this thesis.

The major source of aircraft noise at take-off is jet noise. If jet noise is not adequately addressed environmental impact concerns will constrain the planned growth of the air transport system. A considerable amount of research worldwide has therefore been aimed at identifying ways to reduce jet noise including development of a predictive tool that can estimate the noise generated by new nozzle designs. Current noise prediction techniques, however, still require the input of empirically calibrated noise source models and their performance is still inadequate. In addition, development of detailed noise source identification measurements and the associated understanding of how to control (and reduce) the noise at the source has been limited. The fundamental turbulence property which acts as the source of propagating noise in shear layers is the two-point space-time velocity correlation (Rijkl). Very few measurements exist for this property to guide model development. It is therefore the aim of the work reported in this thesis to provide new experimental data that helps identify the turbulence sources located within the shear layer of jets. The technique of Partical Imaging Velocimetry (PIV) is used to capture directly the flowfield and all relevant turbulent statistics.

Due to the competitive nature of airline industry and the desire to minimise aircraft weight, there is a continual drive to develop lightweight, reliable and more comfortable seating solutions, in particular, a new generation slim economy seat. The key design challenge is to maximise the “living space” for the passenger, with strict adherence to the ‘Crash Safety Regulations’. Cranfield University is addressing the needs of airliners, seat manufactures and safety regulating bodies by designing a completely novel seat structure coined as “Sleep Seat”. A generous angle of recline (40 degree), movement of “Seat Pan” along the gradient, fixed outer shell of the backrest, and a unique single “Forward Beam” design distinguishes “Sleep Seat” form current generation seats. It is an ultra-lightweight design weighing 8kg (typical seat weight is 11kg). It has to sustain the static (CS 25.561) and dynamic (CS25.562) “Emergency landing” loads as specified by “Certification Specifications (CS). Apart from maintaining structural integrity; a seat-structure must not deform, which would impede evacuation, should absorb energy so that the loads transferred to Occupants are within human tolerance limits and should always maintain survivable space around the Occupant. All these parameters, which increase a life-expectancy in a ‘survivable’ crash, can be estimated using either experimental testing or virtual simulation tools such as “Finite Element Analysis (FEA). Design of the “Sleep Seat” is still in its conceptual phase and therefore experimental testing for all the design iterations involved is unrealistic, given a measure of the costs and timescales involved. Therefore focus of research is to develop practical and robust FE methodologies to assess static and dynamic performances of a seat-structure so as to compare different design concepts based on their strength, seat interface loads (a limit defined by strength of aircraft-floor), maximum deformations and cross-sectional forces ... [cont.].