The effects of variations in composition on the decomposition process in Al-Zn-Mg-Cu alloys (i.e. – 7xxx-series aluminum alloy) were studied emphasizing their effect on mechanical properties. Several experimental quaternary alloys were studied to compare their behavior with commercial 7xxx-series alloys. The investigation included studies on the effects of natural aging, artificial aging, quench sensitivity, precipitate free zone formation, and homogenization. Additionally, “true aging” curves (i.e. – hardness/strength vs. conductivity) were presented in order to visualize and quantify the entire precipitation process. It is obvious that fluctuations in the main alloying elements/processing parameters can alter the precipitation process, but the purpose of this work was to quantify those changes using standard industrial techniques. It was found that natural aging was detrimental for strength in the T6 temper for alloys containing more than 1.0 wt.% Cu, and was shown to alter the coarsening kinetics in the over-aged condition (T7). Conversely, for alloys with Cu contents less than 0.5% natural aging was shown to be beneficial for strength. Altering the Zn:Mg ratio was also shown to effect natural aging response of an alloy in addition to introducing additional precipitation processes (T-phase). Therefore, this work is a blueprint for advanced alloy manufacturing that allows for the rapid production of new alloys and tempers by narrowing the research focus depending on an alloy’s composition.

The desire to reduce weight in automotive products is driven by a need to improve efficiency. As such, to allow further weight reduction, higher performance aluminium alloys are in demand for sheet metal body structures. Due to their high strength to weight ratio 7xxx alloys are seen as an ideal candidate for this, however their use to date has been limited by poor formability. Previous work indicated that by moving to high temperatures (>350°C) or by using a soft temper (W), good formability could be achieved but the samples required further heat treatment post-forming. This work explored the warm forming temperature range to improve formability whilst developing the required properties during processing. The performance of a 7xxx candidate alloy, 7021, has been assessed in stretching and drawing operations, both at room temperature and over the elevated temperature range of 150-250°C. The microstructure and other properties of the alloy were investigated in W, T4 and T6 tempers, before and after testing, through a range of techniques, including DSC, DMTA, SEM, EBSD and TEM.In the T4 temper, UTS and proof stress increased with temperature up to 190°C, due to dynamic precipitation. Increasing temperature only provided a modest increase in strain to failure for both the T4 and T6 temper. Cup height was not significantly improved in the warm forming temperature range during Erichsen cup testing. By deep drawing at 250°C it was possible to fully draw a cup (with an LDR of 2.2) in both the T4 and T6 temper of 7021, with both tempers having comparable post-forming hardness. This indicates that at 250°C the starting condition has no impact on drawability. Although full drawability is achieved at 250°C the final product would require further heat treatment if it were to replace 6016. However, by deep drawing 7021-T4 at 190°C, a fully formed cup was produced with a hardness between that of the T4 and T6 temper. The microstructure of the formed cup showed no grain boundary precipitation and a fine distribution of the strengthening phase η', suggesting there is a dynamic effect on the precipitation during deep drawing at this temperature. In conclusion, the work has shown that warm forming does not significantly improve stretching behaviour of 7021, but by using warm forming temperatures deep drawing is improved.

Casting, Solidification, Aluminum, Physical Metallurgy, Mechanical Metallurgy, Strengthening Model, Aluminum Wrought Alloys, Aluminum 7xxx Series, Al-Zn-Mg-Cu / Over the past decades, researchers in casting fields, especially in semi-solid metal state, have endeavored to find new ways to enable the Al wrought alloys of casting using the conventional casting processes; mainly in order to improve the product properties and decrease the product cost. The thixoforming and rheocasting processes have been presented as ways by which the microstructure of Al-base wrought alloys can be changed into non-dendritic, which in turn can lead to improvement to the mechanical properties. This can be because the effect of the non-dendritic microstructure on the mechanical properties of the material. Unfortunately, these processes have proved to be cost prohibitive and be a bit complicated for commercial applications. Further, conventional casting of Al-base wrought alloys along with their superior properties and performance have been a challenge for foundry industry due to the main disadvantage of hot tearing or hot cracking during solidification process. This can render the cast component ineffective. To overcome the disadvantages of thixoforming and rheocasting processes, Controlled Diffusion Solidification (CDS) process was innovated mainly to enable casting of aluminum wrought alloys with a non-dendritic morphology of the primary Al phase in the resultant cast microstructure and thus alleviating the problem of hot tearing and obtaining a cost effective product with improved mechanical properties. The CDS is a simple process involving mixing of two precursor alloys of different thermal masses (temperature and solute) and subsequently casting the resultant mixture of the desired solute composition and temperature as a near net shaped cast product. The process can easily be commercialized with a marginal capital cost required for set up such as the addition of an extra holding furnace. Further, the CDS process would prove itself to be unique in its ability to cast Al-based wrought alloys into near net shaped components without additional processes and cost. The originality of this study is to present a viable casting process for the Al-7xxx wrought alloys (Al-Zn-Mg-Cu); by which the Al-7xxx family alloys are presented in cast condition to have an acceptable uniaxial property range that is comparable with their wrought counterparts. This study presents the process and alloy parameters necessary for the casting of Al-7xxx wrought alloys (Al-Zn-Mg-Cu), by using the CDS process coupling with tilt pour gravity casting (TPGC) machine. The uniaxial tensile mechanical properties of several Al-7xxx CDS castings under various heat treatment conditions, namely, solutionizing (T4), peak aged (T6) and annealing (O), necessary for development of an ageing process on the material were investigated and presented. The tilt pour gravity casting process coupled with the CDS technology was employed to demonstrate the ability to cast Al-7xxx wrought alloys into high integrity components with high strength and ductility. The microstructure characterization was carried out by Electron Microscopy (TEM, SEM and EDS) and DSC test experiments for all the as cast (F), T4, T6 and anneals (O) conditions of the CDS cast components. Also, the predictive capabilities for the yield strength of Al 7xxx alloys CDS cast components was investigated using structural-properties modeling for the various strengthening effects that are recently proposed specifically for the Al-7xxx wrought counterparts. The study has successfully led to a more in-depth understanding of the innovative CDS casting process by applying it to several compositions of Al-7xxx wrought alloys in an industrial scale CDS casting experiments, using tilt pour gravity casting (TPGC) machine. This will hopefully lead us to a clearer path towards commercializing the CDS process and obtaining a viable casting process for Al-base wrought alloys into near net shape components without much change to economics of the casting process. / Dissertation / Doctor of Philosophy (PhD) / Casting, Solidification, Aluminum, Physical Metallurgy, Mechanical Metallurgy, Strengthening Model, Aluminum Wrought Alloys, Aluminum 7xxx Series, Al-Zn-Mg-Cu