This thesis presents an introduction into surface acoustics wave (SAW) unidirectional transducer (UDT) technologies and identifies advantages and disadvantages of various approaches. A complete model of the three-phase unidirectional structure is presented for the purpose of design analysis. This model incorporates the effects of the electrodes and transducer pattern along with the equivalent circuit model of the transducer structure. The model, when included with the appropriate peripheral components for transducer phasing and matching, can be used to determine accurately the frequency response of a given transducer structure. Such a model is well suited for implementation on a digital computer. With this in mind, the necessary FORTRAN 77 software was developed and is presented which is an addition part of the SAW computer aided design (CAD) facilities at UCF-COE. An analysis example is given and the results are compared to published data.

Plasma cleaning is the most effective dry process to remove surface contaminates from a SAW (Surface Acoustical Wave) device. Consistent gas pressures, flows, and good electrical connections between the chamber shelves are necessary for the process to function predictably. In addition, operation of the monitoring system must be transparent to the plasma cleaning unit. This thesis describes a simple solution to the complex problem of monitoring a plasma cleaning system. The monitoring system uses the LabVIEW® G programming language and hardware, both products of National Instruments, Inc.®, to monitor critical parameters necessary to achieve a consistent process when cleaning these devices.

No description available.

Thesis (M.S.)--Oregon State University, 2010. / Printout. Includes bibliographical references (leaves 118-123). Also available on the World Wide Web.

Thesis (Ph. D.)--Drexel University, 2007. / Includes abstract and vita. Includes bibliographical references (leaf 195).

No description available.

This thesis introduces a solution to the problem of time and memory space requirements associated with the manipulation/creation of solid state device layout. Through the use of a hierarchical organization of data and a tailored indexing technique, the software described here, referred to as Saw Draw, is capable of manipulating huge amounts of data in a short period of time. This program was written for surface acoustic wave (SAW) device layout but works for a broad range of devices to include semiconductors, microstrip and others. Due to the large number of details which must be stored for each SAW structure, simply displaying a typical SAW device can become exceedingly tedious. When an entire mask of devices is organized, disk storage requirements can become prohibitive. This software has been designed to minimize both of these critical problems. This work describes the capabilities, structure and special algorithms used in Saw Draw. Included is an example of how a SAW device might be created and a listing of the program code in the Appendix.

Surface Acoustic Wave delay lines have been used as probes for chemical analysis. The interaction between matter adjacent to the SAW device surface and the propagating Raleigh wave caused measurable changes in the amplitude, phase and resonant frequency of the wave. The effectiveness of various electronic detection schemes was evaluated along with the response of the device to changes in pressure and temperature. A lithium niobate SAW device was used as a detector for gas chromatography. Frequency shifts of a SAW oscillator provided the highest sensitivity to compounds eluting from the G.C. column. Sensitivity and specificity of the detector to polar and non-polar organic compounds was greatly enhanced by thin chemical coatings applied to the detector surface. Submicrogram quantities of material were easily detected. Linearity and dynamic range of the detection system was poor. Numerous refinements remain to be made which could significantly improve performance. Thermomechanical analysis of thin polymer films were accomplished using a 32 MHz quartz delay line. Very large wave amplitude shifts were observed as the polymer reached its glass transition temperature. Tg measurements were performed on samples clamped to the surface and cast on the surface. Agreement with low frequency dynamic mechanical measurements was good for the clamped specimens, indicating the absence of wave coupling. Specimens cast on the surface experienced large Tg shifts and therefore were coupled to the surface wave. More subtle transitions were also detected. A crystalline transition around room temperature in a TEFLON film clamped to the SAW device provided an easily observed shift in SAW amplitude. Explanations of this behavior have been proposed. The SAW device also provided an ideal vehicle for examining the behavior of thin photoresist films on the surface. Information on solvent evaporation processes and photo-induced crosslinking rate was obtained. The attractive features of the device for polymer thermomechanical analysis include low cost, ruggedness, high sensitivity and ease of use. / Ph. D.

Approved for public release; distribution in unlimited. / Optical turbulence plays an important role in the propagation of electromagnetic waves through the atmosphere because it broadens and distorts the optical beam. A variety of optical, thermal, and acoustic instruments are used to detect the atmospheric turbulence and an acoustic echosounder has proven to be a valuable tool to probe the fine dynamic structure of atmospheric turbulence within first hundred meters above the surface. The first planar acoustic echosounder constructed at the Naval Postgraduate School was by Weingartner and Wroblewski, under Walters' supervision. Moxcey later modified this design by reducing the number of drivers from 25 to 19 and placing the drivers closer together into a hexagonal, close-packed array. This thesis explored the potential sources of the transducer ringing and implemented solutions to the problem. Additionally, we also improved the receiving sensitivity of the echosounder and lowered the electronics noise when receiving. Finally, we applied these techniques to another array assembled with new drivers to improve its performance compared to the previous echosounder array, while measuring and quantifying the level of improvement achieved. / Lieutenant Commander, Republic of China Navy

Thesis (M.S.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 1979. / MICROFICHE COPY AVAILABLE IN ARCHIVES AND ENGINEERING. / Includes bibliographical references. / by André Antoine Merab. / M.S.