Boundary layer separation is an unwanted phenomenon in most technical applications, as for instance on airplane wings, ground vehicles and in internal flow systems. If separation occurs, it causes loss of lift, higher drag and energy losses. It is thus essential to develop methods to eliminate or delay separation.In the present experimental work streamwise vortices are introduced in turbulent boundary layers to transport higher momentum fluid towards the wall. This enables the boundary layer to stay attached at  larger pressure gradients. First the adverse pressure gradient (APG) separation bubbles that are to be eliminated are studied. It is shown that, independent of pressure gradient, the mean velocity defect profiles are self-similar when the scaling proposed by Zagarola and Smits is applied to the data. Then vortex pairs and arrays of vortices of different initial strength are studied in zero pressure gradient (ZPG). Vane-type vortex generators (VGs) are used to generate counter-rotating vortex pairs, and it is shown that the vortex core trajectories scale with the VG height h and the spanwise spacing of the blades. Also the streamwise evolution of the turbulent quantities scale with h. As the vortices are convected downstream they seem to move towards a equidistant state, where the distance from the vortex centres to the wall is half the spanwise distance between two vortices. Yawing the VGs up to 20° do not change the generated circulation of a VG pair. After the ZPG measurements, the VGs where applied in the APG mentioned above. It is shown that that the circulation needed to eliminate separation is nearly independent of the pressure gradient and that the streamwise position of the VG array relative to the separated region is not critical to the control effect. In a similar APG jet vortex generators (VGJs) are shown to as effective as the passive VGs. The ratio VR of jet velocity and test section inlet velocity is varied and a control effectiveness optimum is found for VR=5. At 40° yaw the VGJs have only lost approximately 20% of the control effect. For pulsed VGJs the pulsing frequency, the duty cycle and VR were varied. It was shown that to achieve maximum control effect the injected mass flow rate should be as large as possible, within an optimal range of jet VRs. For a given injected mass flow rate, the important parameter was shown to be the injection time t1. A non-dimensional injection time is defined as t1+ = t1Ujet/d, where d is the jet orifice diameter. Here, the optimal  t1+ was 100-200. / QC 20100825

The object of the present work is to experimentally study the case of a turbulent boundary layer subjected to an Adverse Pressure Gradient (APG) with separation and reattachment. The effect of unsteadiness on turbulent boundary layer separation by means two different methods were explored viz. the effect of local forcing by acoustic waves and effect of wakes on separation bubble. The experiments were conducted in a low speed open circuit blower type wind tunnel. The turbulent separation bubble was created on the test plate by a contoured ceiling which created the adverse pressure gradient. The velocities were measured using single element hot wire and X-wire. Limited studies on quasi shear stress were also conducted using surface mounted hot film probes. Static pressure was measured using a projection manometer. Boundary layer is tripped near the leading edge of the flat plate to ensure a turbulent boundary layer. Surface pressure distribution and flow visualization were conducted as part of diagnostics. In the case of laminar separation bubble, lot of investigations have been done on the effect of unsteady wake and the most important conclusion was that the wake induces `bypass' transition to turbulence and since the turbulent boundary layer is more resistant to separation, it remains attached. In the case of turbulent separation bubble, laminar-turbulent transition is not relevant and if the bubble is suppressed, it should be by some other mechanism. This is what we seek to unravel in this study. A closer look at the mean velocity profiles reveal the occurrence of inflection point before separation as in the case of laminar separation bubble and the peak values of turbulence intensities correspond to the location of point of inflection. Turbulent separation correlations proposed by various investigators were compared with the present results and are found to be in good agreement. Surface flow visualization pictures are used to get qualitative information. The wall forcing on the separation bubble was done using a speaker which blows a small amount of air when the diaphragm moves up and sucks in when the diaphragm moves down. The blowing effect seems to be more effective in suppressing the separation compared to suction. The interaction with wake is studied using an unsteady bar which is moving up and down. The inflection point in the mean velocity distribution seems to move closer to the wall with the impingement o the wake. Also the turbulence intensities have increased and seem to move closer to the wall. The displacement and momentum thickness have increased and the shape factor has decreased which indicates suppression of the bubble. The quasi shear stress in the separated region also increased which indicates suppression of separation. While the oncoming unsteady wake might be a parcel of fluid with defect velocity when seen in isolation, in comparison to the velocity defect in the separation bubble, it is a region of velocity excess. As a result, one can expect the impingement of the unsteady wake on the TSB to transport momentum thereby contributing to separation reduction. But the mechanism of separation is different from laminar separation bubble affected by wakes. The suppression in the case of turbulent separation bubble is partly due to the entrainment of turbulence and partly due to the kinematic impact of the wake on the bubble.