<p>Train transportation is a vital part of the transportation system of today anddue to its safe and environmental friendly concept it will be even more impor-tant in the future. The speeds of trains have increased continuously and withhigher speeds the aerodynamic effects become even more important. One aero-dynamic effect that is of vital importance for passengers’ and track workers’safety is slipstream, i.e. the flow that is dragged by the train. Earlier ex-perimental studies have found that for high-speed passenger trains the largestslipstream velocities occur in the wake. Therefore the work in this thesis isdevoted to wake flows. First a test case, a surface-mounted cube, is simulatedto test the analysis methodology that is later applied to a train geometry, theAerodynamic Train Model (ATM). Results on both geometries are comparedwith other studies, which are either numerical or experimental. The comparisonfor the cube between simulated results and other studies is satisfactory, whiledue to a trip wire in the experiment the results for the ATM do not match.The computed flow fields are used to compute the POD and Koopman modes.For the cube this is done in two regions of the flow, one to compare with a priorpublished study Manhart & Wengle (1993) and another covering more of theflow and especially the wake of the cube. For the ATM, a region containing theimportant flow structures is identified in the wake, by looking at instantaneousand fluctuating velocities. To ensure converged POD modes two methods toinvestigate the convergence are proposed, tested and applied. Analysis of themodes enables the identification of the important flow structures. The flowtopologies of the two geometries are very different and the flow structures arealso different, but the same methodology can be applied in both cases. For thesurface-mounted cube, three groups of flow structures are found. First groupis the mean flow and then two kinds of perturbations around the mean flow.The first perturbation is at the edge of the wake, relating to the shear layerbetween the free stream and the disturbed flow. The second perturbation isinside the wake and is the convection of vortices. These groups would then betypical of the separation bubble that exists in the wake of the cube. For theATM the main flow topology consists of two counter rotating vortices. Thiscan be seen in the decomposed modes, which, except for the mean flow, almostonly contain flow structures relating to these vortices.</p> / QC 20100518 / Gröna Tåget

This document is a report summering the master thesis work dealing with the Computational Fluid Dynamic (CFD) study of the flow around a high-speed train. The model is a scaled 1:50 generic train with two cars, one inter-car gap and simplified bogies. A platform is set on the side of the train since one of the aim of the study is to look at the consequences of the phenomena in the wake on people or objects standing on the platform. The slipstream is one of this phenomena, it is due to the fact that the viscous air is dragged when the train is passing. If too strong, it can move or destabilize people or objects on the platform. In addition of the slipstream study, a velocity profile study, a drag and lift coefficients analyze as well as a Q-factor study and a frequency study have been realized. Some results of these different studies are compared with the ones obtained on the same model with a Delayed Detached Eddy Simulation (DDES). Since the flow is turbulent, for those different studies, the flow has been simulated with a Reynolds Averaged Navier-Stokes equation model (RANS) which is the k-ω SST model for the turbulence. The study of the slipstream allowed to calculate the Technical Specification for Interoperability (TSI) which must not be higher that the European Union requirement set at 15.5 m/s, the result obtained is 8.1 m/s which is then lower than the limit. The velocity profile shows similarities with the DDES results even though it is less detailed. The same conclusion is done for the Q-plot where is clearly visible the two counter-rotating vortices in the wake. Finally, a Fast Fourier Transform algorithm has been applied to instantaneous velocity results in the wake of the train in order to get the frequency of the aerodynamic phenomena in that wake. The main frequency is 25 Hz and corresponds to a Strouhal number of 0.1, quite closed to the results obtained with DDES which is 0.085. The results of the RANS and DDES are reasonably similar and by regarding at the large difference between the cell numbers (respectively 8 500 000 and 20 000 000) it can be conclude that in some ways the RANS model can be preferred at the DDES to save time for the computation but it does not contain the small scales resolved by the DDES.

Train transportation is a vital part of the transportation system of today anddue to its safe and environmental friendly concept it will be even more impor-tant in the future. The speeds of trains have increased continuously and withhigher speeds the aerodynamic effects become even more important. One aero-dynamic effect that is of vital importance for passengers’ and track workers’safety is slipstream, i.e. the flow that is dragged by the train. Earlier ex-perimental studies have found that for high-speed passenger trains the largestslipstream velocities occur in the wake. Therefore the work in this thesis isdevoted to wake flows. First a test case, a surface-mounted cube, is simulatedto test the analysis methodology that is later applied to a train geometry, theAerodynamic Train Model (ATM). Results on both geometries are comparedwith other studies, which are either numerical or experimental. The comparisonfor the cube between simulated results and other studies is satisfactory, whiledue to a trip wire in the experiment the results for the ATM do not match.The computed flow fields are used to compute the POD and Koopman modes.For the cube this is done in two regions of the flow, one to compare with a priorpublished study Manhart &amp; Wengle (1993) and another covering more of theflow and especially the wake of the cube. For the ATM, a region containing theimportant flow structures is identified in the wake, by looking at instantaneousand fluctuating velocities. To ensure converged POD modes two methods toinvestigate the convergence are proposed, tested and applied. Analysis of themodes enables the identification of the important flow structures. The flowtopologies of the two geometries are very different and the flow structures arealso different, but the same methodology can be applied in both cases. For thesurface-mounted cube, three groups of flow structures are found. First groupis the mean flow and then two kinds of perturbations around the mean flow.The first perturbation is at the edge of the wake, relating to the shear layerbetween the free stream and the disturbed flow. The second perturbation isinside the wake and is the convection of vortices. These groups would then betypical of the separation bubble that exists in the wake of the cube. For theATM the main flow topology consists of two counter rotating vortices. Thiscan be seen in the decomposed modes, which, except for the mean flow, almostonly contain flow structures relating to these vortices. / QC 20100518 / Gröna Tåget