High-response pressure measurements of a high-speed, 10- stage, axial-flow compressor operating in rotating stall are analyzed. Procedures used to digitize analog voltages and calibrate pressure transducers are presented. From total and static pressures measured at the exit of the test compressor, stall cell Mach number distributions are calculated and used to study the effects of discharge throttle levels and variable vane changes on the 10th-stage rotating stall cells. Results indicate that significant transition zones exist between the reverse flow and peak Mach number of the stall cell cycle. Since the axial Mach numbers of the stall cell cycle are constantly changing, the amount of leading and trailing edge transition zones and fully unstalled flow zones are not easily defined. A method is devised to approximate the different flow zone ranges and correlate them to in-stall pressure characteristic behavior of the 10th stage of the test compressor. Changes in the time-averaged pressure characteristics are found to correlate with changes in the rotating stall flow zones. A lower pressure coefficient appears to correspond to an increase in the ratio of trailing to leading edge transition zone size and the average transition zone size. Results also suggest that recovery hysteresis in the test compressor is characterized by reverse flow in the rotating stall cell. / Master of Science

The failure of the Tacoma Narrows Bridge in November 1940 was a major course of the beginning of research on the Aerodynamic Stability of Suspension Bridges. Wind has wrecked suspension bridges for over a century but the underlying cause, an increasing harmonic amplitude due to wind, has been ignored until recently. For many years bridges have been designed to withstand horizontal wind pressure, but the lift force and the overturning moment due to wind have been overlooked. This investigation, in part, was conducted so that aerodynamic coefficients of certain bridge sections not heretofore investigated could be determined. With data from these tests engineers can determine beforehand whether the sections, if used, will be safe against uplifting, sliding, overturning, and of building up oscillations of catastrophic proportions. The second part of this thesis is devoted to the determination of the torsional oscillation effects in order to predict the dynamic wind characteristics of bridge sections. The dynamic tests are necessary to verify the analytical predictions obtained from the static tests and are valuable in obtaining the aerodynamic constants necessary for the complete solution of the bridge analysis. / Master of Science

A research effort aimed at enhancing ACSYNT, a computer program for aircraft conceptual design, has necessitated the development of methods for predicting inlet drag. Originally, the drag of only one inlet type, the variable-geometry conical inlet, could be calculated within ACSYNT. This prompted the present research which resulted in the creation of a modular suite of subroutines that extend the capability of ACSYNT. Using this new source code, ACSYNT can now predict the drag of subsonic and supersonic pitot inlets, fixed- and variable-geometry conical inlets, and two-dimensional supersonic inlets. Even though the requirement of computational efficiency has necessitated that many simplifications be made in the analysis, the drag calculations have a sound physical basis. The semi-empirical methods have been extracted from a number of sources based on an extensive literature survey, and these have been enhanced to encompass the full range of inlet operating conditions. The effectiveness of the methods has been demonstrated by comparing some results of the predictions to published data. / Master of Science

A method for predicting unsteady, subsonic aeroelastic responses has been developed. The technique accounts for aerodynamic nonlinearities associated with angles of attack, vortex-dominated flow, static deformations, and unsteady behavior. The angle of attack is limited only by the occurrence of stall or vortex bursting near the wing. The fluid and the wing together are treated as a single dynamical system, and the equations of motion for the structure and flowfield are integrated simultaneously and interactively in the time domain. The method employs an iterative scheme based on a predictor-corrector technique. The aerodynamic loads are computed by the general unsteady vortex-lattice method and are determined simultaneously with the motion of the wing. Because the unsteady vortex-lattice method predicts the wake as part of the solution, the history of the motion is taken into account; hysteresis is predicted. Two models are used to demonstrate the technique: a rigid wing on an elastic support experiencing plunge and pitch about the elastic axis, and an elastic wing rigidly supported at the root chord experiencing spanwise bending and twisting. The method can be readily extended to account for structural nonlinearities and/or substitute aerodynamic load models. The time domain solution coupled with the unsteady vortex-lattice method provides the capability of graphically depicting wing and wake motion. / Ph. D.

Instrumentation has been designed to process the signals from two types of skin friction gages and a microfabricated heat flux gage. Design changes for the skin friction gages are presented which will improve the performance of the two transducers. The instrumentation is simple in design and use and has been designed to maximize the performance of the skin friction and heat flux gages. The instrumentation is battery powered to minimize noise levels and to maintain instrumentation portability. A high-quality instrumentation amplifier, a voltage regulator, and a custom-designed circuit board have been combined to produce an instrumentation package which is stable and durable. The instrumentation has been specifically designed to handle low-level signals and can operate over a wide range of frequencies. Problems commonly associated with low-level signal conditioning like electrical noise, nonlinearities, and output drift are addressed. The performance specifications of the instrumentation are presented along with sample gage measurements. / Master of Science

Thesis (PhD (Mechanical Engineering))--University of Stellenbosch, 1990. / Leaves printed on single pages, preliminary pages i- viii and numbered pages 1-1-R5. Includes bibliography, list of tables and figures and list of appendices. Digitized at 330 dpi black and white PDF format (OCR),using KODAK i 1220 PLUS scanner. / ENGLISH ABSTRACT: A numerical procedure for predicting the effect of inlet flow distortions on the performance of axial flow fans is proposed. The study is aimed specifically at fans of low solidity and low hub-to-tip ratios, which have attained some importance with the advent of large directly air-cooled power stations in certain arid regions of the world. The numerical model is an extension to cylindrical polar coordinates of the SIMPLEN algorithm that has been developed by the author previously. The algorithm is implemented in a computer code, FLOVAX, which solves the incompressible Navier-Stokes equations, augmented by the k-Ɛ model of turbulence, on a computational domain that is aligned with the cylindrical polar coordinate system. Several relatively simple flow problems are solved to verify the code: laminar stagnation flow, laminar flow near a rotating disk, turbulent flow near a propeller, turbulent flow through an abrupt axisymmetric expansion, and turbulent swirling flow in an annulus. Good agreement is obtained between the numerical solutions and the corresponding analytical, empirical or published experimental and numerical results. Some experimental results are also presented: measurements of shaft power, volume flow rate and static pressure rise were taken in a setup comprising an axial flow fan mounted in the wall of a wind tunnel. The wind tunnel was used to provide flow across the fan intake, thus establishing distorted inflow conditions. Detailed measurements of the velocity and static pressure distributions in the duct downstream of the fan rotor were also performed. It is clear from the results that flow across the intake of the test fan has a detrimental effect on its performance in that an increased amount of power is necessary to deliver the same flow rate as with no crossflow. In the numerical predictions, blade element theory is used to model the thrust and torque exerted by the fan blades on the air. The numerical results generally confirm the results of the experiment, although the increase in power is underestimated: an increase of only approximately half of the measured increase is predicted. Several recommendations for improvement of the numerical procedure are made. / AFRIKAANSE OPSOMMING: 'n Numeriese prosedure vir die voorspelling van die invloed van versteurings in inlaatvloei op die werking van aksiaalwaaiers word daargestel. Die studie is spesifiek gemik op waaiers van lae soliditeit en lae lempunt-tot-naafverhoudings. Waaiers van hierdie tipe het belangrikheid verwerf sedert die onlangse totstandkoming van groot lugverkoelde kragstasies in sekere droe werelddele. Die numeriese model is 'n uitbreiding na silindriese poolkoordinate van die SIMPLEN-algoritme wat voorheen deur die skrywer ontwikkel is. Die algoritme word geimplementeer in 'n rekenaarkode, FLOVAX, wat die onsamedukbare Navier-Stokes-vergelykings, aangevul deur die k-Ɛ-turbulensiemodel, oplos op 'n berekeningsgebied wat saamval met die silindriese poolkoordinaatstelsel. Verskeie relatief eenvoudige vloeiprobleme word opgelos ter verifikasie van die kode: laminere stagnasievloei, laminere vloei op 'n roterende skyf, turbulente vloei deur 'n propeller, turbulente vloei deur 'n aksiaalsimmetriese vernouing, en turbulente roterende vloei in 'n annulus. Goeie ooreenstemming tussen die numeriese oplossings en die ooreenstemmende analitiese, empiriese of gepubliseerde eksperimentele en numeriese resultate is verkry. Eksperimentele resultate word ook aangebied: metings van asdrywing, volumevloei en statiese drukstyging is geneem in 'n opstelling wat bestaan het uit 'n aksiaalwaaier wat in die wand van 'n windtonnel gemonteer is. Die windtonnel is gebruik om versteurde-invloei-toestande te genereer in die vorm van dwarsvloei oor die waaier-inlaat. Snelheids- en statiese drukverdelings in die kanaal stroom-af van die waaierrotor is ook gemeet. Dit blyk duidelik uit die resultate dat die dwarsvloei oor die inlaat van die toetswaaier 'n nadelige uitwerking het op die werking daarvan in die opsig dat meer drywing nodig is om dieselfde vloeitempo te handhaaf as wat die geval is sonder dwarsvloei. Vir die numeriese voorspellings word van lem-element-teorie gebruik gemaak om die stukrag en draaimoment wat deur die waaier op die lug uitgeoefen word, te modelleer. Die numeriese resultate bevestig oor die algemeen die eksperimentele resultate, alhoewel die drywingstoename onderskat word met sowat die helfte van die gemete toename. Verskeie aanbevelings ter verbetering van die numeriese prosedure word gemaak.

Indiana University-Purdue University Indianapolis (IUPUI) / This study seeks to improve the understanding of inlet conditions of a large rotor-stator cavity in a turbofan engine, often referred to as the drive cone cavity (DCC). The inlet flow is better understood through a higher fidelity computational fluid dynamics (CFD) modeling of the inlet to the cavity, and a coupled finite element (FE) thermal to CFD fluid analysis of the cavity in order to accurately predict engine component temperatures. Accurately predicting temperature distribution in the cavity is important because temperatures directly affect the material properties including Young's modulus, yield strength, fatigue strength, creep properties. All of these properties directly affect the life of critical engine components. In addition, temperatures cause thermal expansion which changes clearances and in turn affects engine efficiency. The DCC is fed from the last stage of the high pressure compressor. One of its primary functions is to purge the air over the rotor wall to prevent it from overheating. Aero-thermal conditions within the DCC cavity are particularly challenging to predict due to the complex air flow and high heat transfer in the rotating component. Thus, in order to accurately predict metal temperatures a two-way coupled CFD-FE analysis is needed. Historically, when the cavity airflow is modeled for engine design purposes, the inlet condition has been over-simplified for the CFD analysis which impacts the results, particularly in the region around the compressor disc rim. The inlet is typically simplified by circumferentially averaging the velocity field at the inlet to the cavity which removes the effect of pressure wakes from the upstream rotor blades. The way in which these non-axisymmetric flow characteristics affect metal temperatures is not well understood. In addition, a constant air temperature scaled from a previous analysis is used as the simplified cavity inlet air temperature. Therefore, the objectives of this study are: (a) model the DCC cavity with a more physically representative inlet condition while coupling the solid thermal analysis and compressible air flow analysis that includes the fluid velocity, pressure, and temperature fields; (b) run a coupled analysis whose boundary conditions come from computational models, rather than thermocouple data; (c) validate the model using available experimental data; and (d) based on the validation, determine if the model can be used to predict air inlet and metal temperatures for new engine geometries. Verification with experimental results showed that the coupled analysis with the 3D no-bolt CFD model with predictive boundary conditions, over-predicted the HP6 offtake temperature by 16k. The maximum error was an over-prediction of 50k while the average error was 17k. The predictive model with 3D bolts also predicted cavity temperatures with an average error of 17k. For the two CFD models with predicted boundary conditions, the case without bolts performed better than the case with bolts. This is due to the flow errors caused by placing stationary bolts in a rotating reference frame. Therefore it is recommended that this type of analysis only be attempted for drive cone cavities with no bolts or shielded bolts.