No description available.

A new, consistent direct-iterative method is proposed for the solution of the aerodynamic inverse design problem. Direct-iterative methods couple analysis and shape modification methods to iteratively determine the geometry required to support a target surface pressure. The proposed method includes a consistent shape modification method wherein the identical governing equations are used in both portions of the design procedure. The new shape modification method is simple, having been developed from a truncated, quasi-analytical Taylor's series expansion of the global governing equations. This method includes a unique solution algorithm and a design tangency boundary condition which directly relates the target pressure to shape modification. The new design method was evaluated with an upwind, cell-centered finite-volume formulation of the two-dimensional Euler equations. Controlled inverse design tests were conducted with a symmetric channel where the initial and target geometries were known. The geometric design variable was a channel-wall ramp angle, 0, which is nominally five degrees. Target geometries were defined with ramp angle perturbations of J10 = 2 %, 10%, and 20 %. The new design method was demonstrated to accurately predict the target geometries for subsonic, transonic, and supersonic test cases; M=0.30, 0.85, and 2.00. The supersonic test case efficiently solved the design tests and required very few iterations. A stable and convergent solution process was also demonstrated for the lower speed test cases using an under-relaxed geometry update procedure. The development and demonstration of the consistent direct-iterative method herein represent the important first steps required for a new research area for the advancement of aerodynamic inverse design methods. / Ph. D.

The dynamic response of the compression system is a key factor in determining the operability characteristics of an aircraft gas turbine engine subjected to various transient environmental and control inputs. Computer models have been developed to simulate this response. The primary inputs to these models are the wide-range, steady-state compressor stage characteristics. To reduce the dependence of these dynamic models on experimental performance data, significant effort has been devoted to the development of stage characteristic prediction techniques. As part of this ongoing effort, a model to simulate rotating stall inception and development in axial-flow compressor stages was constructed. This model was applied to an isolated rotor build to investigate the sensitivity of the predicted stall behavior to the shape of the high-incidence portions of the blading relative total pressure loss and turning angle characteristics, as well as to the rotor speed. In addition, the predicted steady-state, stalled rotor performance was compared with corresponding low-speed, experimental data. By superimposing small flow perturbations on the rotor flow field over a range of initial operating conditions, it was demonstrated that stall inception occurs only for initial relative flow incidence near some critical value, defined as the incidence for which the relative total pressure losses incurred in the blade passage increase sharply. For initial operating points away from the critical one, no propagating disturbance was predicted. Also, a strong sensitivity of the predicted stall behavior to the shape of the high-incidence portion of the relative total pressure loss characteristic was observed with increased-slope curves resulting in earlier stall inception and larger amplitude stall disturbances. The effect of increased-slope loss curves on the predicted steady-state rotor performance was to cause a more abrupt drop in the flow and total pressure rise coefficients at the stall limit. Comparatively, varying the shape of the turning angle characteristic or the rotor speed had only a slight effect on the simulated rotating stall phenomena. Finally, the predicted install total pressure characteristic for a selected low-speed case was compared with experimental data with favorable results. / Master of Science

Modern, high performance aircraft are required to be able to fly and be controlled over a wide variety of flight conditions. In order to predict the aircraft behavior and control requirements over the entire flight regime it is necessary to have a proper aerodynamic model. Flight conditions at high angles of attack lead to separated flows making the aerodynamic model more difficult to obtain. In this research wind tunnel experiments are performed on an F-5 air-craft model at high angles of attack, with small oscillations about the body oriented roll axis. In addition the free stream environment can be configured in one of three ways: l) straight uniform flow, 2) curved flow to simulated a horizontal turn, and 3) rolling flow to simulated a roll motion about the relative Velocity vector. / Ph. D.

A new rotor dynamic wake distortion model, which can be used to account for the rotor transient wake distortion effect on inflow across the rotor disk during helicopter maneuvering and transitional flight in both hover and forward flight conditions, is developed. The dynamic growths of the induced inflow perturbation across the rotor disk during different transient maneuvers, such as a step pitch or roll rate, a step climb rate and a step change of advance ratio are investigated by using a dynamic vortex tube analysis. Based on the vortex tube results, a rotor dynamic wake distortion model, which is expressed in terms of a set of ordinary differential equations, with rotor longitudinal and lateral wake curvatures, wake skew and wake spacing as states, is developed. Also, both the Pitt-Peters dynamic inflow model and the Peters-He finite state inflow model for axial or forward flight are augmented to account for rotor dynamic wake distortion effect during helicopter maneuvering flight. To model the aerodynamic interaction among main rotor, tail rotor and empennage caused by rotor wake curvature effect during helicopter maneuvering flight, a reduced order model based on a vortex tube analysis is developed. Both the augmented Pitt-Peters dynamic inflow model and the augmented Peters-He finite state inflow model, combined with the developed dynamic wake distortion model, together with the interaction model are implemented in a generic helicopter simulation program of UH-60 Black Hawk helicopter and the simulated vehicle control responses in both time domain and frequency domain are compared with flight test data of a UH-60 Black Hawk helicopter in both hover and low speed forward flight conditions.

An Ocean Current Turbine (OCT) numerical simulation for creating, testing and tuning flight and power takeoff controllers, as well as for farm layout optimization is presented. This simulation utilizes a novel approach for analytically describing oceanic turbulence. This approach has been integrated into a previously developed turbine simulation that uses unsteady Blade Element Momentum theory. Using this, the dynamical response and power production of a single OCT operating in ambient turbulence is quantified. An approach for integrating wake effects into this single device numerical simulation is presented for predicting OCT performance within a farm. To accomplish this, far wake characteristics behind a turbine are numerically described using analytic expressions derived from wind turbine wake models. These expressions are tuned to match OCT wake characteristics calculated from CFD analyses and experimental data. Turbine wake is characterized in terms of increased turbulence intensities and decreased mean wake velocities. These parameters are calculated based on the performance of the upstream OCT and integrated into the environmental models used by downstream OCT. Simulation results are presented that quantify the effects of wakes on downstream turbine performance over a wide range of relative downstream and cross stream locations for both moored and bottom mounted turbine systems. This is done to enable the development and testing of flight and power takeoff controllers designed for maximizing energy production and reduce turbine loadings. / Includes bibliography. / Dissertation (Ph.D.)--Florida Atlantic University, 2016. / FAU Electronic Theses and Dissertations Collection