Spelling suggestions: "subject:"airliquid interfaces"" "subject:"microliquid interfaces""
1 |
Magnetically targeted deposition and retention of particles in the airways for drug deliveryAlly, Javed Maqsud 06 1900 (has links)
This thesis examines the mechanisms of magnetic particle deposition and retention in human airways for magnetically targeted drug delivery. As this is a novel application, fundamental studies were performed to establish the necessary background knowledge for further development.
Magnetic particle deposition from an aerosol in simulated airway conditions was studied using numerical and experimental models. The model results showed qualitative agreement; discrepancies were due to particle aggregation, which enhances deposition. Aerosol flow rate had a limited effect; the main factor in effective deposition was the proximity of the particle trajectories to the magnets. This spatial bias shows the importance of particle distribution in the flow as well as magnetic field geometry. These studies demonstrated the feasibility of capturing magnet particles from aerosol in airway conditions.
For retention, clearance of particles due to motion of the mucus lining of the airways must be overcome. Particle retention was studied in vitro using various liquids to simulate mucus and identify relevant parameters. An ex vivo animal tissue model was used to demonstrate feasibility. Retention of 3-5 m diameter iron particles was achieved at reduced liquid/mucus viscosities. Larger (~100 m) particles were retained at normal mucus viscosities. The size dependence shows that particle aggregation after deposition is crucial for effective retention.
In vitro retention experiments showed aggregate size is correlated with liquid viscosity, i.e. formation of aggregates is limited by forces opposing particle motion along the mucus layer interface. To determine these forces, particle motion on various air-liquid interfaces, chosen to simulate different mucus properties in isolation, was studied. When surfactants are present, as in the mucus layer, particle motion is limited by a velocity-dependent surface tension gradient as well as viscous drag.
Pulling particles through the mucus layer into the tissue beneath was also considered as a potential retention strategy. The force required to pull particles through the mucus layer was also studied using various liquids to simulate mucus properties. In addition to the surface tension force holding the particles at the interface, hydrodynamic forces must be overcome to pull particles into or out of a liquid film such as the mucus layer.
|
2 |
Modeling and defect analysis of step and flash imprint lithography and photolithographyChauhan, Siddharth 07 December 2010 (has links)
In 1960's Gordon Moore predicted that the increase in the number of components in integrated circuits would exponentially decrease the relative manufacturing cost per component with time. The semiconductor industry has managed to keep that pace for nearly 45 years and one of the main contributors to this phenomenal improvement in technology is advancement in the field of lithography. However, the technical challenges ahead are severe and the future roadmap laid by the International Technology Roadmap for Semiconductors looks mostly red (i.e. no solution has been found to specific problem). There are efforts in the industry and academia directed toward development of newer, alternative lithographic techniques. Step and Flash Imprint Lithography (SFIL) has recently emerged as one of the most promising alternatives, capable of producing high resolution patterns. While it has numerous advantages over conventional photolithography, several engineering challenges must be overcome to eliminate defects due to the nature of contact imprinting if SFIL is to be a viable alternative technique for manufacturing tomorrow's integrated circuits. The complete filling of template features is vital in order for the SFIL imprint process to truly replicate the template features. The feature filling phenomena for SFIL was analyzed by studying diffusion of a gas, entrapped in the features, through liquid imprint resist. A simulation of the dynamics of feature filling for different pattern configurations and process conditions during the SFIL imprint step is presented. Simulations show that initial filling is pressure-controlled and very rapid; while the rest of the feature filling is diffusion-controlled, but fast enough that diffusion of entrapped gas is not a cause for non-filling of features. A theory describing pinning of an air-liquid interface at the feature edge of a template during the SFIL imprint step was developed, which shows that pinning is the main cause of non-filling of features. Pinning occurs when the pressure at the air-liquid interface reaches the pressure of the bulk liquid. At this condition, there is no pressure gradient or driving force to move the liquid and fill the feature. The effect of several parameters on pinning was examined. A SFIL process window was established and template modifications are proposed that minimize the pinning at the feature edge while still preventing any extrusion along the mesa (pattern containing area on the template) edge. Part of semiconductor manufacturing community believes that optical lithography has the capability to drive this industry further and is committed to the continuous improvement of current optical patterning approaches. Some of the major challenges with shrinking critical dimensions (CDs) in coming years are the control of line-edge roughness (LER) and other related defects. The current CDs are such that the presence or absence of even a single polymer molecule can have a considerable impact on LER. Therefore molecular level understanding of each step in the patterning process is required. Computer simulations are a cost-effective approach to explore the huge process space. Mesoscale modeling is one promising approach to simulations because it captures the stochastic phenomena at a molecular level within reasonable computational time. The modeling and simulation of the post-exposure bake (PEB) and the photoresist dissolution steps are presented. The new simulator enables efficient exploration of the statistical excursions that lead to LER and the formation of insoluble residues during the dissolution process. The relative contributions of the PEB and the dissolution step to the LER have also been examined in the low/high frequency domain. The simulations were also used to assess the commonly proposed measures to reduce LER. The goal of the work was to achieve quantification of the effect of changes in resist composition, developer concentration, and process variables on LER and the associated defectivity. / text
|
3 |
Magnetically targeted deposition and retention of particles in the airways for drug deliveryAlly, Javed Maqsud Unknown Date
No description available.
|
Page generated in 0.0768 seconds