Spelling suggestions: "subject:"airplanes -- 1design anda construction."" "subject:"airplanes -- 1design ando construction.""
1 |
A multilevel decomposition procedure for the preliminary wing design of a high-speed civil transport aircraftRohl, Peter Jurgen 05 1900 (has links)
No description available.
|
2 |
The design and development of a human-powered airplaneMcAvoy, James Marion 08 1900 (has links)
No description available.
|
3 |
A physics based robust methodology for aerodynamic design analysis and optimizationJimeno, Jesus 08 1900 (has links)
No description available.
|
4 |
An investigation of the out-of-plane deflection behavior of thin sheets with cut-outs in a tensile fieldZielsdorff, George Frank 05 1900 (has links)
No description available.
|
5 |
Mechanical behavior of composite corrugated structures for skin of morphing aircraftDayyani, Iman January 2015 (has links)
Corrugated panels have gained considerable popularity in a range of engineering applications, particularly in morphing skin applications due to their remarkable anisotropic characteristics. They are stiff to withstand the aerodynamic loads and flexible to enable the morphing deformations. In this thesis a detailed review of the literature on corrugated structures is presented. The specific characteristics of corrugated structures such as: high anisotropic behaviour, high stiffness and good durability, lightness and cost effectiveness are discussed comprehensively. However for the application in morphing aircraft, the optimal design of the corrugated panels requires simple models of these structures to be incorporated into multi-disciplinary system models. Therefore equivalent structural models are required that retain the dependence on the geometric parameters and material properties of the corrugated panels. In this regard, two analytical solutions based on homogenization and super element techniques are presented to calculate the equivalent mechanical properties of the corrugated skin. Different experimental and numerical models are investigated to verify the accuracy and efficiency of the presented equivalent models. The parametric studies of different corrugation shapes demonstrate the suitability of the proposed super element for application in further detailed design investigations. Then the design and multi-objective optimization of an elastomer coated composite corrugated skin for the camber morphing aerofoil is presented. The geometric parameters of the corrugated skin are optimized to minimize the in-plane stiffness and the weight of the skin and to maximize the flexural out-of-plane stiffness of the corrugated skin. A finite element code for thin beam elements is used with the aggregate Newton's method to optimize the geometric parameters of the coated corrugated panel. The advantages of the corrugated skin over the elastomer skin for the camber morphing structure are discussed. Moreover, a finite element simulation of the camber morphing internal structure with the corrugated skin is performed under typical aerodynamic and structural loadings to check the design approach.
|
6 |
The Investigation and Design of a Powered, Single-Man Parawing AircraftMerrell, Calvin J. 01 August 1965 (has links)
During the last few years there has been an increasing interest in a high-lift wing configuration known as the flex-wing, or parawing. The parawing consists basically of a flexible membrane such as cloth, attached to two leading edges (or booms) and a keel as shown in Figure 1. At angles of attack (��) greater than the billowing angle (��). the air impinges on the under side of the membrane and forces it into a double-arch shape at each cross-section. When straight leading edges are used, each arch approximates the shape of a conical section. A cylindrical section is obtained by giving the leading edge a circular arch shape as seen from head on
|
7 |
A methodology for technology identification, evaluation, and selection in conceptual and preliminary aircraft designKirby, Michelle Rene 05 1900 (has links)
No description available.
|
8 |
Nonlinear aeroelastic analysis, flight dynamics, and control of a complete aircraftPatil, Mayuresh J. 05 1900 (has links)
No description available.
|
9 |
Nonlinear aeroelastic effects in damaged composite aerospace structuresZhang, Haochuan 12 1900 (has links)
No description available.
|
10 |
Intersection and filleting of non-uniform B-spline surfacesJones, Robert W. 24 April 2009 (has links)
Preliminary aircraft design codes requIre a more complete and integrated geometry definition than that used by conceptual design codes. This thesis documents the design and creation of an interactive CAD system which converts the geometry descriptions commonly used in conceptual aircraft design codes to descriptions that meet the requirements of preliminary design systems. In particular, the conversion of ACSYNT Hermite surface data of aircraft models to the non-uniform hi-cubic B-Spline surface representation is addressed. The topics discussed in this thesis include the design and development of an interactive graphics user interface, the design and coding of an intersection method for non-uniform hi-cubic B-Spline surfaces utilizing subdivision techniques and the development of a one-dimensional filleting algorithm for blending surfaces along iso-parametric curves. / Master of Science
|
Page generated in 0.1228 seconds