No description available.

Thesis (Sc.D.)--Massachusetts Institute of Technology, Dept. of Nuclear Engineering, 1982. / MICROFICHE COPY AVAILABLE IN ARCHIVES AND SCIENCE. / Includes bibliographical references. / by Ronald George Ballinger. / Sc.D.

Thesis (Ph.D.)--Massachusetts Institute of Technology, Dept. of Materials Science and Engineering, 1982. / MICROFICHE COPY AVAILABLE IN ARCHIVES AND SCIENCE / Vita. / Includes bibliographical references. / by Arnaldo Homobono Paes de Andrade. / Ph.D.

No description available.

The effect of crack tip strain rate (CTSR) on environmentally assisted cracking was studied for alloys AA-7075 (Al-Zn-Mg-Cu) and AA-8090 (Al-Li-Cu-Mg) in the artificially aged condition. Fatigue pre-cracked double cantilever beam (DCB) specimen were employed with the crack plane parallel to the rolling plane. The cracking behaviour under monotonic and cyclic loading conditions was investigated in aqueous sodium chloride solutions with and without additions of sodium chromate as a corrosion mhibitor. CTSR values were described in terms of K-rate ∆K/∆t (ie. dK/dt) as a measured average over the loading period of a fatigue cycle. This allowed a comparison with CTSR's of monotonically increasing load or constant load tests. At frequencies ≤1 Hz, the load was applied with a triangular wave form. A high frequency of 30 Hz was obtained by sinusoidal loading. Expressed as K-rate, CTSR values were varied over 7 orders of magnitude from 10⁵MPa√m/s to 10² MPa√m/s. Stress intensities investigated were mainly around region II values with respect to SCC K-log(da/dt) behaviour. At low K-rates, real time crack velocities (da/dt) measured under monotonic slow loading or constant load conditions were comparable to crack velocities obtained with cyclic loading experiments. As the K-rate was increased from low values, typical of constant load experiments, the real time crack velocities decreased. This was caused by plasticity induced crack growth retardation effects and a decrease in crack tip film rupture events during the unloading part of a cycle. The crack propagation rate decreased until minimal crack advance increments per cycle were dictated by mechanical parameters acting on a hydrogen embrittled crack tip region. Under monotonic loading conditions region II crack velocities were not influenced by an increase in K-rate which was explained with a mass transport controlled cracking process. Tests with alloy 7075 at intermediate K-rates and a high R-ratio of 0.78 allowed a crack tunnelling mechanism to operate. This overcame the plasticity induced crack growth retardation and, therefore, cracks propagated at the same rates as during low K-rate tests where no retardation phenomena were encountered. Scanning electron microscope investigations revealed a striated intergranular fracture surface of alloy 7075 if tested at K-rates above the transition value to K-rate independent crack propagation rates. Individual striations could be matched on opposing fracture surfaces and the striation spacing corresponded to the average crack propagation increment per cycle. The striations, therefore, were formed as part of the crack advance during every fatigue cycle. At the lower K-rates no striations were present but micro tear ridges could be found on the intergranular fracture facets indicating that dissolution processes alone did not cause the intergranular crack advance. Alloy 8090 did not reveal significant changes in fractography over the entire K-rate range investigated, except at the highest K-rates where small interlocking steps could be detected on some opposing transgranular fracture surfaces. In general, however, the crack path at all K-rates was mainly intergranular with dimpled fracture facets. Alloy 8090 exhibited a high resistance to SCC with fatigue pre-cracked DCB specimen. Therefore, to obtain crack velocity values with low K-rate monotonic loading tests very long test durations would have been necessary. It is concluded that the transition from intergranular SCC to intergranular CF occurs at a critical K-rate. Below the critical K-rate crack velocities are not increased by cyclic loading. Instead crack growth retardation effects can result in lower real time crack velocities than those typical for constant load tests at comparable stress intensities but much lower K-rates. / Applied Science, Faculty of / Materials Engineering, Department of / Graduate

A series of experiments was performed in an attempt to measure the effects of surface residual stresses on the stress corrosion cracking/hydrogen embrittlement (SCC/HE) behavior of AISI 4340 steel. Stress corrosion tests were performed under load control on cylindrical and notched tensile specimens in acidified 3.5% NaCl solution. The electrochemical potential of the specimens was maintained at -0.7 V versus a saturated calomel reference electrode. Time to failure for specimens tested at various applied and residual stress levels was measured. Stress relieved specimens as well as specimens containing mechanically induced residual stresses were tested. Residual stresses were estimated using Neuber's rule and were measured using an x-ray diffraction technique. In all cases, the sum of the applied and residual stresses was greater than zero. Test results showed the initiation of SCC/HE cracks to be insensitive to the effects of surface residual stresses under the conditions evaluated. This is probably a result of the total time to failure criterion used to evaluate the SCC/HE tests. The extremely aggressive environment used in these experiments apparently led to rapid crack initiation, even in specimens containing compressive residual stresses. Another possible explanation of the insensitivity of this series of tests is crack initiation in the interior of the specimens below the depth of the mechanically induced residual stresses. / Master of Science

This thesis deals with corrosion problems of underwater turbines in marine environment. The effect of a tensile stress on the uniform corrosion rate of a metal bar is studied, and an analytical model predicting the time of service of a bar under a tensile load in a corrosive environment is proposed. Stress corrosion relationships are provided for different type of alloys, and different types of relationships. Dolinskii's and Gutman's models are studied and extended to a general order polynomial, along with a Least Square and Spline Interpolation of the experimental data. In a second part, the effect of the passive film, delaying the initiation of the corrosion process, is studied. Finally, an algorithm predicting the time of service of a cracked bar is provided, using the stress corrosion assumption, along with a validation using experimental data. / by Yohann Miglis. / Thesis (M.S.C.S.)--Florida Atlantic University, 2012. / Includes bibliography. / Electronic reproduction. Boca Raton, Fla., 2012. Mode of access: World Wide Web.