The researches of this thesis are divided into two parts. One is to investigate the applicability of ANSI C63.5 in high frequencies of 1 GHz to 6 GHz. In general, the Standard Site Method (SSM) of C63.5 is usually used to calculate the antenna factors for the calibration of broadband antennas. Through the theoretical calculations, the numerical simulations and measurements, we found that the discrepancies between the calibrated results of horizontal and vertical polarization related to the un-dipole-like pattern in higher frequencies. Furthermore, we analyzed the relations of the antenna factors, the heights of receive antennas and the radiation patterns. We also found that the predicted calibration results can be close to the practical ones by including the effects of radiation patterns. The other research is to study the issue about the ground plane size of a test site. The ground plane size of a qualified test site must be larger than the minimum size defined by C63.7. For this reason, we provide a method which combines the tilted antennas measurement with a trapezoid shape ground. By using this method in the smaller ground size, we can obtain the measured results close to those obtained in the larger ground size. This method can effectively reduce the required ground size and then decrease the installation cost of a test site. Meanwhile, this method can be applied for both of the horizontal and vertical polarizations.

The CISPR of IEC in European and the ANSI in American use the model of site attenuation to evaluate and quantify the quality of OATS. The ANSI also uses the concept of Normalized Site Attenuation (NSA) to eliminate the effects brought about by different antennas, which may cause the inaccuracy of site attenuation. To stringently require the quality of OATS, the measured values of NSA have to be compared with the theoretical ones. If their differences are within (+/-)4 dB at all frequencies, the test environment of the OATS can be accepted. At present, the theoretical values of NSA are used as a standard for verifying the OATS in the world. However, many non-ideal factors derived from certain assumptions and simplifications of the NSA may cause the measured NSA to deviate from the theoretical values. To understand the manner and extent of the effects, in this thesis we find out the non-ideal factors by studying the NSA by numerically simulating the effects of each factor on NSA measurement by the method of moment (MoM), and the results are analyzed and discussed. We find that there is a difference of 6 dB on the NSA when the impedance of the receive antenna is mismatched. Meanwhile, we also study the relationship between the conductivity of non-perfect electrical conductor and the ideal value of NSA. We conclude that a ground plane made by metal can be regarded as a PEC one. However, the values of NSA will increase if the conductivity of ground plane is below 1000 S/m. Besides, considering the humid Taiwan climate in particular, we investigate the condition of a thin layer of water covering the ground plane after rain and the results show that the effect of the water plane will decrease the values of NSA. As for the measurement at a distance of 3 m, a deviation of 2 dB at low frequencies arises from the effect of near field for the case of horizontal polarization. Finally as for the non-conducting table in OATS, our results show that the larger values of relative permittivity and conductivity of table result in the larger change of NSA value. The difference can be 3 dB for the case with a wooden table. With results of our research, the effects of non-ideal factors on NSA measurement can be comprehended clearly. The comparison of the differences also can be used as a reference for the modification of the NSA measurement in the future.

This thesis first discusses the ground plane effects of a test site on the antenna factors (AFs) of hybrid antenna (biconical log-periodic dipole array). Meanwhile, the effects of mutual coupling between antenna and its image, and the variation of active phase center are also discussed. From these analyses, a hybrid method, based on the modified SSM (Standard Site Method) and the PCPM (Phase Center and Pattern Matching) applied to the hybrid antenna for NSA (Normalized Site Attenuation) measurement is proposed. By this method, the low geometry- dependent AFs of hybrid antenna can be obtained to produce more reasonable NSA values for a test site. Secondly, this thesis proposes a simple, fast, and accurate method to calibrate the free-space AFs of broadband EMC (Electromagnetic Compatibility) antennas. This method adopts a fixed-height configuration and a MUSIC (MUltiple SIgnal Classification) algorithm. This configuration significantly shortens measurement time and removes height-dependent calibration errors. Meanwhile, the MUSIC algorithm can remove unexpected reflections from the ground plane or any other reflecting objects, by which the free-space AFs can be calculated. In addition, this method can also automatically compensate for the phase center shift, which makes measurement easier and more convenient. To verify this method, the calibrated results are compared with other published standard methods: the mean differences can be as low as 0.25 dB for the LPDA (log-periodic dipole array), 0.42 dB for the hybrid antennas, and 0.36 dB for the horn antennas. Finally, this thesis provides a method of using two equivalent negative inductances from two terminals of three coupled inductors to reduce the parasitic inductances of a typical three-capacitor EMI (Electromagnetic Interference) filter. Theoretical analysis and formula deduction for the design of two equivalent negative inductances are demonstrated. The experimental results show that the insertion losses of a three-capacitor EMI filter at 50 MHz can be reduced by 16.8 dB for the DM (differential-mode) and by 19.2 dB for the CM (common-mode). In Appendix A of this thesis, an extended study of the effect of ground plane on antenna¡¦s radiation is described. A simple V-shape edge-groove design for a finite ground plane can effectively reduce the pattern ripples of a monopole. The optimal design of proposed structure can reduce the peak-to-peak pattern ripples from 26 to 4.5 dB.

Abstract Whether an Open Area Test Site (OATS) is qualified is based on the Normalized Site Attenuation (NSA). The purpose is to eliminate the influence of Antenna Factor (AF). Usually the AF provided by the manufacturer adopts the Standard Site Method (SSM) and is quoted from measurements at a 10-m range. In practice, the AF varies with the measurement conditions. This uncertainly will translate into error in NSA measurements. Currently radiated electromagnetic interference measurement mostly adopts the broadband antennas, and LPDA is one of the antennas used extensively. However, the AF provided by the manufacturer does not consider shifts in the phase center of LPDA with frequency. In the meantime the radiation pattern of LPDA is different from that of a short dipole. The investigation of this thesis will focus on these two parts. In determining the phase center of LPDA antenna we adopt the average shift of phase center to improve the AF. The numerical simulation results show that such an arrangement can result in improvement. We also use the method of PCPM (Phase Center and Pattern Matching) to modify the AF under different conditions of measurement when a ground plane is present. Our study, by using the numerical simulation and measurement, shows that this indeed improves the variation of AF over that obtained by SSM. In addition, efforts are also made to have a detailed discussion in mutually coupling effects between the LPDA antenna and the ground plane, in order to distinguish the impact on AF due to the coupling of the LPDA antenna and its image. Our numerical simulation results indicate that it does not have a significant effect.

Master’s thesis is focused on making the acquaintance of EMC issues and ways of electromagnetic field scanner RS321 utilization for pre-compliance measurements. First part contains analysis of available equipment’s influence on measurement results on the basis of gathered specification. Next part includes an example measurement used as operational manual for scanner and its controlling program. The most important part is correction evaluation for performed EMI measurement of signal generator using its EMC certification protocol and application of gained correction curve on independent EMI measurement of device tested by EMC testing laboratory. Other possibilities of scanner utilization are mentioned in the next chapters. Last part of the thesis contains suitability evaluation of EMC scanner on the basis of findings from performed measurements.