abstract: Within the past two decades, metasurfaces, with their unique ability to tailor the wavefront, have attracted scientific attention. Along with many other research areas, RADAR cross-section (RCS)-reduction techniques have also benefited from metasurface technology. In this dissertation, a novel technique to synthesize the RCS-reduction metasurfaces is presented. This technique unifies the two most widely studied and two well-established modern RCS-reduction methods: checkerboard RCS-reduction andgradient-index RCS-reduction. It also overcomes the limitations associated with these RCS-reduction methods. It synthesizes the RCS-reduction metasurfaces, which can be juxtaposed with almost any existing metasurface, to reduce its RCS. The proposed technique is fundamentally based on scattering cancellation. Finally, an example of the RCS-reduction metasurface has been synthesized and introduced to reduce the RCS of an existing high-gain metasurface ground plane. After that, various ways of obtaining ultrabroadband RCS-reduction using the same technique are proposed, which overcome the fundamental limitation of the conventional checkerboard metasurfaces, where the reflection phase difference of (180+-37) degrees is required to achieve 10-dB RCS reduction. First, the guideline on how to select Artificial Magnetic Conductors (AMCs) is explained with an example of a blended checkerboard architecture where a 10-dB RCS reduction is observed over 83% of the bandwidth. Further, by modifying the architecture of the blended checkerboard metasurface, the 10-dB RCS reduction bandwidth increased to 91% fractional bandwidth. All the proposed architectures are validated using measured data for fabricated prototypes. Critical steps for designing the ultrabroadband RCS reduction checkerboard surface are summarized. Finally, a broadband technique to reduce the RCS of complex targets is presented. By using the proposed technique, the problem of reducing the RCS contribution from such multiple-bounces simplifies to identifying and implementing a set of orthogonal functions. Robust guidelines for avoiding grating lobes are provided using array theory. The 90 degree dihedral corner is used to verify the proposed technique. Measurements are reported for a fabricated prototype, where a 70% RCS-reduction bandwidth is observed. To generalize the method, a 45 degree dihedral corner, with a quadruple-bounce mechanism, is considered. Generalized guidelines are summarized and applied to reduce the RCS of complex targets using the proposed method. / Dissertation/Thesis / Doctoral Dissertation Electrical Engineering 2020

abstract: Flexibility, reconfigurability and wearability technologies for antenna designs are presented, investigated and merged in this work. Prior to the design of these radiating elements, a study is conducted on several flexible substrates and how to fabricate flexible devices. Furthermore, the integration of active devices into the flexible substrates is also investigated. A new approach of designing inkjet-printed flexible reconfigurable antennas, based on the concept of printed slot elements, is proposed. An alternate technique to reconfigure the folded slot antenna is also reported. The proposed radiator works for both Wireless Local Area Network (WLAN) and Worldwide Interoperability for Microwave Access (WiMAX) applications. The flexible reconfigurable antenna is also redesigned to resonate at both (2.4/5.2 GHz) for WLAN devices and its Multiple-Input Multiple-Output (MIMO) configuration is reported. Two orthogonal elements are used to form the MIMO antenna system for better isolation. The wearability of the proposed flexible reconfigurable radiator is also discussed. Since wearable antennas operate close to the human body, which is considered as a lossy tissue, an isolation between the radiating elements and human body is required to improve the radiation characteristics and to reduce the Specific Absorption Rate (SAR). The proposed antenna is redesigned on an Artificial Magnetic Conductor (AMC) surface that also functions as a ground plane to isolate the radiator from the human body. To examine its performance as a body-worn device, it is measured at different positions on the human body. Furthermore, simulations show that the SAR level is reduced when using the AMC surface. The proposed wearable antenna works for both Wireless Body Area Network (WBAN) and WiMAX body-worn wireless devices. Electromagnetic bandgap (EBG) structures are used to suppress surface wave propagation in printed antennas. However, due to the presence of vias, not all of them can be utilized in flexible radiators. Thus, a Perforated High Impedance Surface (PHIS) is proposed which suppresses the surface waves without the need of vias, and it also serves as a ground plane for flexible antennas. The surface wave suppression and the antenna applications of the proposed PHIS surface are discussed. / Dissertation/Thesis / Doctoral Dissertation Electrical Engineering 2017

Le travail de cette thèse est en rapport avec les métamatériaux et ses applications. Tout d’abord, un état de l’art est dressé en présentant leur évolution depuis leur apparition en 19ème siècle jusqu’au nos jours. Les notions sur les milieux chirale, bi-anisotrope, cristaux photoniques et quelques applications dans ces milieux sont données. Ensuite, nous présentons les équations classiques de Maxwell dans les milieux complexes. L’effet bi-anisotrope dans les métamatériaux est ensuite validé par l’extraction des paramètres caractéristiques du matériau main gauche (LHM). La validation a été faite en utilisant deux types différents du résonateur avec inclusion (SRR). Les métamatériaux sont également étudiés comme des cristaux photoniques quand les dimensions utilisées sont de l’ordre de la longueur d’onde correspondant.De plus, les résonateurs SRR et multi-SRR sont analysés du point de vue analytique et électromagnétique afin d’extraire leur fréquence de résonance. Par conséquent, ces composants peuvent être introduits dans différents types de conception; La surface conductrice magnétique artificielle (AMC) illustre un cas explicite et efficace de ces derniers. Une antenne dipôle, placée sur cette surface à la place d’un plan de masse conventionnel, a été étudiée comme une application des métamatériaux. Les résultats relatifs sur la directivité, le gain et le coefficient de réflexion montrent une nette amélioration. Une antenne multi-bandes, comme une autre application des métamatériaux, a également été conçue et simulée. Le résonateur SRR est inséré dans l’antenne de départ afin de créer une autre résonance, et par conséquent une autre bande est ainsi créée. / The work in this thesis deals with metamaterials, its components and applications. A historical overview about these materials, features and researches in the domain are presented. Chiral media, binaisotropic materials and photonic crystals are also studied in order to visualize physics behind metamaterials.Electromagnetic properties in complex media are widely investigated. Starting from Maxwell’s equations, bi-anisotropic materials and their effect are deeply analyzed whereas two types of Split Ring Resonator (SRR) are treated to determine constitutive parameters of Left Handed Materials (LHM). The metamaterials are also studied as photonic crystals since the effective medium approach is not applicable when the dimensions of the inclusions tend to the operating wavelength.Moreover, SRRs and Multi SRRs are synthesized analytically and electromagnetically in order to extract their resonant frequencies. Consequently, these components could be introduced in any design; Artificial Magnetic Conductor (AMC) surface is an efficient case. Thus, a low profile antenna positioned over such surface is examined as an application of metamaterials. The results of directivity, gain and reflection coefficient are of great importance and affirm the employing of metamaterials in such applications. A dual band PCB antenna, as another application of metamaterials, is designed and simulated. The SRR element studied in the previous chapters is used as the trap which inserted in the arm of the antenna in order to create another resonance, and consequently another band is created.