Spelling suggestions: "subject:"artificial muscle"" "subject:"aartificial muscle""
1 |
The development of artificial muscles using textile structuresStubbs, Laura Kate January 2011 (has links)
The aim of this project was to investigate the use of textile structures as muscles to assist people with muscular deficiency or paralysis. Due to the average life expectancy continuing to increase, support for those needing assistance to move unaided is also increasing. The purpose of this project was to try to help a patient who would normally need assistance, to move their arm unaided. It could also help with rehabilitation of muscular injuries and increasing strength and reducing muscular fatigue of manual workers. The approach considered was to develop an extra corporal device for the upper limbs, providing the main required motions. Most devices currently available use motors and gearboxes to assist in limb movement. This study investigated a way of mimicking the contraction of biological skeletal muscles to create a motion that is as human as possible with a soft, flexible and lightweight construction. Electroactive polymers (EAPs) and pneumatic artificial muscles (PAMs) were investigated. It became clear that at present, the EAPs were unable to create the forces and speed of contraction required for this application. The use of pneumatics to create artificial muscles was developed upon. PAMs, like the McKibben muscle and the pleated pneumatic muscle mimic the natural contraction of skeletal muscle. These current PAMs were used as a basis to develop a new type of pneumatic artificial muscle in this project. A 90 mm ball-like structure was developed, produced from an air impermeable rubber coated cotton fabric. Joining three oval panels together created a 3-D spherical shape. Three of these structures were linked together, and when inflated, created an acceptable level of contraction and force. This method of producing artificial muscles created a soft, lightweight and flexible actuator with scope for different arrangements, sizes and positions of the muscle structure. The contraction process was mathematically modelled. This calculated the predicted rate and level of contraction of a 2-D muscle structure. These mathematical findings were able to be compared to the practical results, and produced similar contraction characteristics. The muscle structures were incorporated into a garment to form a type of muscle suit which could be worn to assist movement. This garment has an aluminium frame to protect the wearer's bones from stresses from the contracting muscles. This study has shown that the muscle suit developed can create movement for wearers that would normally need assistance, and also reduce muscle fatigue, which would be useful for manual workers. This is incorporated into a functional and wearable garment, which is easy to dress and more lightweight and aesthetically pleasing than current muscle suits.
|
2 |
Engineering a compliant muscle joint for dynamic locomotion in very rough terrainGonzales, Matthew Robert 27 February 2012 (has links)
In humanoid robotics, there is a long pursuit of making bipeds capable of walking in highly unstructured and roughly sensed environments. Within this goal, our objective is to develop a compliant bipedal humanoid robot, based on McKibben pneumatic actuators that can move in these terrains as well as quickly adapt to unpredicted variations on the contact state. We present here the first part of our work, focusing on the design, construction and control of a pneumatic robotic joint capable of achieving the control performance necessary for responding compliantly and accurately to contact transitions while delivering high forces needed to handle the physical challenges associated with rough terrains. In particular, we address our progress in the mechanical and embedded electronic design, actuator modeling, and compliant control strategies for a robotic joint based on fluidic pneumatic artificial muscles (PAMs). The proposed robotic joint has been validated experimentally, exploring various aspects of its performance as well as its shortcomings, but overall demonstrating the potential benefits of using pneumatic muscles. / text
|
3 |
Low-Profile Polymer Actuator Fabrication for Spastic Hand ExoskeletonsBahrami, Sanaz 02 August 2018 (has links)
Spasticity is a neurological impairment that presents itself in the form of a continuous muscle contraction, with the key motor deficit being impaired hand function. Hand exoskeleton technologies play a vital role in the therapeutic rehabilitation of this condition. The optimal design of these devices is currently a challenge due to the limited availability of actuation devices that are light weight, portable, and aesthetically pleasing. Natural muscles have many favourable characteristics, such as their high power-to-weight ratio, efficient energy conversion, and fast actuation times. Unfortunately, traditional systems such as pneumatics muscles and electromagnetic motors have yet to attain similar properties. These traditional actuators exhibit hysteretic performance, high manufacturing cost, low stroke, and limited cycle life. In recent years a new category of actuators has been developed from highly twisted and coiled low-cost nylon fibres such as fishing line and conductive sewing thread. These muscles produce a high specific work per cycle with a reversible contraction. This thesis develops and tests these twisted and coiled polymer (TCP) actuators using various nylon and polyethylene polymers in order to establish a foundation for their implementation as a novel actuation device in a spastic hand exoskeleton. An initial comprehensive experimental evaluation of several nylon fibres is completed by attempting to reproduce the work of previous researchers. Subsequently, the information obtained is taken and adapted to the development of UHMWPE TCPs and other types of nylon monofilament. This thesis characterizes the contractility and force output of these novel actuation devices.
|
4 |
Electromechanical Transduction in Ionic Liquid-Swollen Nafion MembranesBennett, Matthew Damon 11 November 2005 (has links)
Traditionally, water has been used as the diluent for ionomeric polymer transducers. The water mobilizes the counterions within the polymer and allows electromechanical transduction to occur. However, these water-swollen devices have limited stability when operated in a non-aqueous environment. In this work, ionic liquids are demonstrated as viable diluents for ionomeric polymer transducers based on Nafion membranes. Ionic liquids are molten salts that are highly thermally stable and have an immeasureably low vapor pressure. Therefore, the ionic liquid-swollen transducers exhibit enhanced stability in their performance when operated for long periods of time in air.
Methods for swelling Nafion membranes with ionic liquids are presented. Also, techniques for plating the ionic liquid-swollen transducers with metal electrodes are discussed. The performance of the ionic liquid-swollen transducers is compared to that of water-swollen transducers and differences are observed. Apart from the superior stability of the ionic liquid-swollen devices, they are observed to not exhibit the characteristic back-relaxation that is often associated with water-swollen transducers and limits their low frequency response. In order to investigate the physics of transduction in the ionic liquid-swollen membranes, structured experiments are performed using two different ionic liquids: 1-ethyl-3-methylimidazolium trofluoromethanesulfonate (EMI-Tf), which is water miscible, and 1-ethyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide (EMI-Im), which is hydrophobic. The other experimental parameters are the counterion of the Nafion membrane and the swelling level of ionic liquid.
Small-angle X-ray scattering (SAXS) is used to characterize the morphology of the ionic liquid-swollen Nafion membranes. The SAXS testing reveals that the clustered morphology of the Nafion membrane is preserved by the EMI-Tf ionic liquid, which is compatible with the hydrophilic cluster phase. By contrast, the hydrophobic EMI-Im ionic liquid is found to disrupt the clustered morphology and lead to partial homogenization of the polymer. This has the effect of inhibiting the ionic conductivity. The SAXS testing also reveals that the mean intercluster spacing increases as the content of ionic liquid and size of the counterions increases. Based on assumptions regarding the swelling mechanism, this is thought to arise from an increase in the mean size of the clusters.
Spectroscopic investigations were also performed using Fourier transform infrared spectroscopy (FTIR) and nuclear magnetic resonance spectroscopy (NMR). These studies show that the ionic liquid interacts with the Nafion polymer by displacing the counterions away from the sulfonate exchange sites. The cations of the ionic liquid then associate with the sulfonate sites and the counterions associate with the anions of the ionic liquid. Above a certain critical uptake of ionic liquid, this displacement is complete and additional ionic liquid does not associate with the ions of the polymer. The critical uptake is found to decrease with increasing size of the counterions. / Ph. D.
|
5 |
Manufacture and Characterization of Ionic Polymer Transducers Employing Non-Precious Metal ElectrodesBennett, Matthew Damon 31 May 2002 (has links)
Ionic polymer membranes are commonly used in fuel cell power generation, water electrolysis and desalinization, chlorine generation, and other niche applications. Since the early 1990s ionic polymer membranes have also shown promise as distributed electromechanical actuators and sensors. The cost of these materials is very high because of the expensive noble metals that are used as the electrodes in these applications, however. Currently, high cost of these devices has prevented them from experiencing widespread use. The goal of the current research project is to study new methods of plating metal electrodes onto ionic polymer membranes in order to reduce the cost of these materials and open the door for potential industrial, aerospace, and biomedical applications.
At this time ionic polymer actuators are only made using gold or platinum as the electrode in a lengthy and labor-intensive process. The current research focuses on using less costly metals and revising the metal deposition process. Several new methods allowing for faster deposition of metals onto ionic polymer membranes are developed and evaluated including sputter-coating, electroless plating, and impregnation/reduction. Using these methods, metal electrodes have been plated onto ionic polymer membranes in processes resulting in a purely surface deposition and in processes resulting in interpenetration of the metal into the polymer. This work shows that electromechanical coupling is present with all of these processes, although results indicate that interpenetration of the electrode is important for good adhesion of the metal and good performance of the transducers.
Also studied were different metals; X-ray photoelectron spectroscopy (XPS) testing shows that the use of non-noble metals as the electrodes results in oxidation of the metal and corresponding loss of performance in the actuator. Noble metals are found to not experience the oxidation problem. Further work shows that non-noble metals can be effectively employed as electrodes if alloyed with noble metals by using a co-reduction technique. Also studied is the use of protective coatings of noble metal to stabilize the non-noble metal electrodes. Using these approaches, a new plating method is developed and the stability of the electrodes made using this method is studied. These results indicate that samples made using this new process may be actauted continuously for over 150,000 cycles with very little degredation in their performance.
Using this new plating method, ionic polymer membrane transducers can be made in less than five hours. Characterization of these new devices shows that they have a mass energy density of 4-20 mJ/kg in the cantilevered mode. This compares well with a baseline material, which is found to have a mass energy density of 3-12 mJ/kg. Composition and morphology of the electrodes made using the new method are investigated using scanning electron microscopy (SEM) and the density and tensile modulus are measured. The density of the new material is found to be approximately 2100 kg/m^3 as compared to about 3200 kg/m^3 for the baseline material. Also, the tensile elastic modulus of the new material is about 55 MPa, or roughly one fourth of the tensile modulus of the baseline material (about 190 MPa). These results indicate that the new materials contain much less noble metal in the electrodes than the baseline material. The sensitivity of these devices has also been quantified and compared to the baseline. Results indicate that the new materials have a sensitivity on the order of 0.1-0.3 uA/mm/s whereas similarly sized samples of the baseline material typically have sensitivities on the order of 0.2-0.8 uA/mm/s. The most important conclusion of this work is that ionic polymer membrane transducers can be made using much less noble metal in the electrode than previously believed without sacrificing the performance of these devices. / Master of Science
|
6 |
Development and Testing of an Unpowered Ankle Exoskeleton for Walking AssistLeclair, Justin January 2016 (has links)
Assistive technologies traditionally rely on either strong actuation or passive structures to provide users with increased strength, support or the ability to perform lost functions. At one end of the spectrum are powered exoskeletons, which significantly increase a user’s strength, but require strong actuators, complex control systems, and heavy power sources. At the other end are orthoses, which are generally unpowered and lightweight devices that rely on their structure’s mechanical behaviour to enhance user’s support and stability. Ideally, assistive technologies should achieve both systems’ characteristics by enhancing human motion abilities while remaining lightweight and efficient. This can be achieved by using distinctive actuators to harness gait energy, towards enhancing human mobility and performance.
Pneumatic Artificial Muscles (PAMs), compliant and flexible, yet powerful and lightweight, present a unique set of characteristics compared to other mechanical actuators in human mobility applications. However, given the need of a compressor and power source, PAMs present a significant challenge, limiting their application. In contrast, PAMs can be implemented as unpowered actuators that act as non-linear elastic elements.
This thesis aims to develop a wearable lightweight unpowered ankle exoskeleton, which relies on the PAM to harness gait energy and compliment the human ankle biomechanical abilities at the push off movement, thusly assisting the user in propelling the body forward during walking. Presently, limited PAM models have been developed to analyse PAM passive behaviour and to assist in designing and selecting the appropriate PAM for unpowered application. Thus, this thesis aims to develop a passive model for the PAM.
To mechanically validate the proposed exoskeleton design, a prototype is fabricated, and tested within an Instron tensile machine setup. The unpowered exoskeleton has shown its ability to provide significant contribution to the ankle timed precisely to release at the push off phase of the gait cycle. Furthermore, the proposed PAM stiffness model is validated experimentally, and accounts for muscle pressure, geometry, material and stretching velocity. This enables the evaluation of the impact of various parameters on the muscle behaviour and designs the PAM accordingly for the unpowered ankle exoskeleton
|
7 |
A computer controlled data acquisition and control system for a shape-memory alloy artificial muscleBambeck, Timothy J. January 1993 (has links)
No description available.
|
8 |
Biologically Inspired Legs and Novel Flow Control Valve Toward a New Approach for Accessible Wearable RoboticsMoffat, Shannon Marija 18 April 2019 (has links)
The Humanoid Walking Robot (HWR) is a research platform for the study of legged and wearable robots actuated with Hydro Muscles. The fluid operated HWR is representative of a class of biologically inspired, and in some aspects highly biomimetic robotic musculoskeletal appendages showing certain advantages in comparison to more conventional artificial limbs and braces for physical therapy/rehabilitation, assistance of daily living, and augmentation. The HWR closely mimics the human body structure and function, including the skeleton, ligaments, tendons, and muscles. The HWR can emulate close to human-like movements even when subjected to simplified control laws. One of the main drawbacks of this approach is the inaccessibility of an appropriate fluid flow management support system, in the form of affordable, lightweight, compact, and good quality valves suitable for robotics applications. To resolve this shortcoming, the Compact Robotic Flow Control Valve (CRFC Valve) is introduced and successfully proof-of-concept tested. The HWR added with the CRFC Valve has potential to be a highly energy efficient, lightweight, controllable, affordable, and customizable solution that can resolve single muscle action.
|
9 |
Design and Material Characterization of a Hyperelastic Tubular Soft CompositeShaheen, Robert January 2017 (has links)
Research within the field of human motion assistive device development, with the purpose of reducing the metabolic cost of daily activities, is seeing the benefits of the exclusive use of passive actuators to store and release energy during the gait cycle. Designs of novel exoskeletons at the University of Ottawa implement the Pneumatic Artificial Muscle (PAM) as the primary method of nonlinear, passive actuation. The PAM is proven as a superior actuator for these devices when compared to the linear mechanical springs used by other researchers. There are, however, challenges regarding PAM pressure loss and the limitation of PAM elongation that have been identified.
This thesis aims to develop a hyperelastic tubular soft composite that replicates the distinctive mechanical behaviour of the PAM without the need for internal pressurization. The final soft composite solution was achieved by impregnating a prefabricated polyethylene terephthalate braided sleeve, held at a high initial fibre angle, with a silicone prepolymer. A comprehensive experimental evaluation was performed on numerous prototypes for a variety of customizable design parameters including: initial fibre angle, silicone stiffness, and braided sleeve style. Moreover, two separate analytical models were formulated based on incompressible finite elasticity theory using either a structural model of Holzapfel’s type, or a phenomenological model of Fung’s type. Both models were in good agreement with the experimental data that were collected through a modified extension-inflation test.
This research has successfully developed, tested, and validated an innovative soft composite that can achieve specific mechanical properties, such as contraction distance and nonlinear stiffness, for optimal use in human motion assistive devices.
|
10 |
Development of Soft Actuation Systems for Use in Human-Centered ApplicationsWirekoh, Jackson O. 01 December 2017 (has links)
In recent years, soft materials have seen increased prevalence in the design of robotic systems and wearables capable of addressing the needs of individuals living with disabilities. In particular, pneumatic artificial muscles (PAMs) have readily been employed in place of electromagnetic actuators due to their ability to produce large forces and motions, while still remaining lightweight, compact, and flexible. Due to the inherent nonlinearity of PAMs however, additional external or embedded sensors must be utilized in order to effectively control the overall system. In the case of external sensors, the bulkiness of the overall system is increased, which places limits on the system’s design. Meanwhile, the traditional cylindrical form factor of PAMs limits their ability to remain compact and results in overly complex fabrication processes when embedded fibers and/or sensing elements are required to provide efficient actuation and control. In order to overcome these limitations, this thesis proposed the design of flat pneumatic artificial muscles (FPAMs) capable of being fabricated using a simple layered manufacturing process, in which water-soluble masks were utilized to create collapsed air chambers. Furthermore, hyperelastic deformation models were developed to approximate the mechanical performance of the FPAMs and were verified through experimental characterization. The feasibility of these design techniques to meet the requirements of human centered applications, including the suppression of hand tremors and catheter ablation procedures, was explored and the potential for these soft actuation systems to act as solutions in other real world applications was demonstrated. We expect the design, fabrication, and modeling techniques developed in this thesis to aid in the development of future wearable devices and motivate new methods for researchers to employ soft pneumatic systems as solutions in human-centered applications.
|
Page generated in 0.0667 seconds