The properties of materials, especially of solids, can be attributed mainly to the phenomena occurring at the surface. Surface engineering deals with altering the surface properties of materials to realize useful functionalities like wear and corrosion resistance, biocompatibility, hardening etc. Among the various methods adopted, plasma surface modification stands out, because of the inherent dry processing nature and little amount of left over chemicals. In conventional plasma systems, the process is carried out in a low pressure environment. This restricts its use in treating vacuum incompatible materials including tissues and bio-medical samples. Moreover, the batch processing nature and use of expensive vacuum pumps put a bottle-neck in the throughput of any production line. The subject matter of this thesis is about developing and optimizing an atmospheric pressure (760 torr) plasma system and to use it for surface modification of polymers. The experimental system developed, consists of two parallel electrodes facing each other, each of which is covered with a dielectric plate. A gap of 4mm exists between the dielectric surfaces, through which an axial flow of the working gas is maintained. When a high voltage is applied across the electrodes, the gas breaks down, creating plasma. The surface of the sample kept in this plasma, undergoes various phenomena, depending on the power applied, type of gas used and gas flow rate. To drive the plasma a high voltage power supply, which is able to generate 10 kV at 5.8 kHz, was developed in the laboratory. By varying the process parameters, the inherent filamentary nature of discharge can be converted to a diffuse uniform glow. The purity of plasma was studied and established by analyzing the optical emission from the plasma. After optimizing the system, it was used to modify the surface properties of polyester sheets. The wetting nature was altered using fluorocarbon and oxygen plasmas, realizing hydrophobic and hydrophilic surfaces. The contact angle of a water droplet made with the surface changed from 72° to 84° degree for hydrophobic and to 22° for hydrophilic surfaces respectively. Through this investigation, an insight to the procedure for developing an Atmospheric glow discharge system was developed. The details about system frame work, the power supply, electrical and optical characterization of the plasma, are well studied and recorded. The work establishes the various parameters to be varied to convert the filamentary discharge to a uniform glow. Purity of the plasma has been studied extensively and the system design and process values essential for maintaining the purity have been dealt with. Finally the plasma was put in use for surface modification of polymers, and the surface wetting nature alteration was studied and quantified.

The aim of this work is the study of plasma processes and the synthesis of organic compounds due to electric discharge generated in gas mixture corresponding to the composition of the atmosphere of Saturn's largest moon Titan. This study focuses on the mimic of Titan's atmosphere at atmospheric pressure and ambient laboratory temperature. The chemical composition of Titan's atmosphere is very similar to atmosphere of prehistoric Earth. Many articles have been published with theoretical model-research, and laboratory experiments are the pursuit of their interconnection. The main aim of thesis is the identification of synthesized gaseous organic, amino, imino and cyano compounds by use to various analytical methods such as the PTR-MS, FTIR and GC-MS. The OES and electric measurements were applied to the determination of selected electric discharge parameters. The gaseous products and radicals formed in an atmospheric discharge fed by different mixtures of N2:CH4 (0,5 up to 5 % of CH4) operated in a flowing regime at the total gas mixture flows from 50 to 200 sccm at different discharge currents from 15 up to 40 mA were determined. A part of experiments was carried out with admixtures of CO2 and hydrogen. This first part of results has been obtained using OES in dependence on the gas mixture composition and supplied power. The bands of the nitrogen second positive and the first negative systems, CN violet system and Swan system of C2 were recorded. Besides them, atomic lines H, H, and C (in the second order) were also observed. These spectra allowed calculation of rotational and vibrational temperatures. FTIR in situ analysis of the gaseous products showed presence of various nitrile compounds and hydrocarbons in all experiments. The HCN, C2H2, NH3 were the main products generated in our system. The dependences of their concentrations on various experimental parameters were measured. The other part of this work was devoted to estimate the influence of CO2 traces addition on the reactivity in the gaseous mixtures mentioned above. Besides the main products mentioned above, CO2 and CO were detected and also some more complicated oxygen molecules has been confirmed but not estimated because of FTIR spectra complexity. In the case of hydrogen traces addition into the reaction gas mixture, no other compounds were determined. Impurities of CO2 as well as hydrogen have a great positive influence on the production efficiency of the major generated compounds at all conditions. The more detailed gaseous products analyses were carried out using the in situ PTR-MS. A huge number of different molecular structures containing nitrile groups (–CN), amino groups (–NH2, –NH–, –N CH3CN > C2H5CN. Besides them, many other hydrocarbons and nitriles were detected. Presence of all compounds was studi