No description available.

Spectroscopic investigations have been carried out on hollow cathode discharges adapted from laser technology for use as a spectroscopic light source and the argon inductively coupled plasma (ICP) as an excitation source for nonmetal emission. High and low voltage aluminum and copper hollow cathode discharges were studied as a source of ionic and resonant atomic metal emission. The high voltage versions achieve strongly positive current-voltage behavior through utilization of the obstructed discharge phenomenon. The current-pressure-intensity-voltage relationships for low and high voltage copper hollow cathode discharges were studied with the inert gases He, Ne, Ar, Kr, and Xe. The intensity for copper resonant atomic emission with the fill gases Ar, Kr, and Xe improved relative to neon in the high voltage lamp when compared to the low voltage lamp. Absorption measurements through the cathode bore show the ground state atom density to increase with the atomic weight of the fill gas at any given level of intensity, at the fill gas pressure yielding highest resonant atomic copper emission. The estimated ion/atom intensity ratio is increased with fill gases which have metastable or ionization energies greater than the excitation energy of the ion transition. A copper hollow cathode lamp incorporating a short positive column discharge in front of the cathode opening was investigated for its lineshape as measured spectroscopically and by its atomic absorption sensitivity. Incorporation of this positive column allowed higher intensities to be obtained at the same line quality as a commercial hollow cathode lamp. An enlarged cathode volume also improves the lineshape at a given intensity. Inductively coupled plasma spectra for the elements C, O, N, Cl, P, S, and Br were obtained in the vacuum ultraviolet utilizing a vacuum polychromator and SWR film. The detection limit for injected O₂ and N₂ detected electronically by the VUV emissions is 1.3 and 0.9 micrograms respectively with this system. A VUV filter photometer was utilized for oxygen and phosphorus analysis. The detection limit for injected oxygen was 1 microgram with this photometer; the detection limit for phosphorus as inorganic phosphate in aqueous solution is 10⁻³ M. The bandpass of the photometer limits its selectivity.

published_or_final_version / Chemistry / Master / Master of Philosophy

published_or_final_version / abstract / Chemistry / Master / Master of Philosophy

No description available.

Thesis (M.Phil.)--University of Hong Kong, 2000. / Includes bibliographical references. Also available in print.

Thesis (M. Phil.)--University of Hong Kong, 1996. / Includes bibliographical references.

Thesis (M. Phil.)--University of Hong Kong, 2000. / Includes bibliographical references.

The accurate determination of wear metals in lubricating fluids is of great potential value in the proper maintainence of all types of machinery. Savings of both time and money have been reported in the military and civilian sectors following the implementation of routine wear metal screening in lubricating oils. Current methods are known to discriminate against metals present in the form of particulates. The first part of this dissertation focusses on the direct determination of wear metals in lubricating oils by atomic emission spectroscopy utilizing an inverted inductively coupled plasma as a source. Data are presented which show the effects of power and viewing position on the signal intensity of a variety of sized iron particulate samples in lubricating oil. The second part of this dissertation describes the characterization of a relatively new spectroscopic source--the dual inductively coupled plasma (DICP). The DICP increases the residence time of the analyte in the source by extending the physical length of the plasma discharge and providing two energy deposition regions. Emission intensity, electron density, ion-to-atom intensity ratios, and calculated temperatures are used to compare the DICP with standard inductively coupled plasmas recorded in the literature.

A thesis submitted to the faculty of science, university of the Witwatersrand, Johannesburg,in fulfilment of the requirements for the degree of Doctor of Philosophy, 1994 / Alternative sample manipulation and sample introduction methods for inductively coupled plasma-atomic emission spectrometry (ICP-AES) and inductively coupled plasma-mass spectrometry (ICP-MS) have been investigated. The broad objectives of the study were to broaden the scope and improve the analytical performance of the techniques. The methods which were investigated were: 1) Laser ablation. This technique was used only in combination with ICP-MS. The technique was not applied to ICP-MS because the laser ablation system is dedicated to the ICP-MS instrument. The laser ablation system was applied to the direct analysis of solid refractory materials, without dissolution of the sample. The main advantages of avoiding the dissolution step are that the sample preparation is rapid, there is no dilution or contamination of the sample, and no loss of volatile analyte elements. The problems which were encountered with the use of laser ablation were firstly, poor precision of measurement relative to solution analysis due to sample particles of widely varying size entering the plasma, and secondly, memory effects when changing from one sample type to another. 2) Flow injection. This sample manipulation method was used in combination with pneumatic nebulization for ICP-AES and ICP-MS. The technique was applied to a number of different analytical problems, with the objectives of speeding up analysis times, increasing the matrix tolerance of the instruments, and automating a variety of sample preparation processes. 3) Hydride generation. This technique was applied to the determination of arsenic and selenium by ICP-AES and ICP-MS, using a novel type of gas, liquid separator. The advantages of the technique were the separation of the analyte elements from interfering matrix species, and increased analyte sensitivity due to the excellent transport efficiency of hydride generation relative to solution nebulization. Numerous advantages have been obtained from the application of these sample manipulation and sample introduction techniques. Methods have been developed for the analysis of materials which are not suited to conventional solution nebulization, and the techniques have been used to improve the efficiency of analysis, to achieve lower detection eliminate, and to eliminate interferences. / GR2017