The purpose of this research is to make an investigation into the crashworthiness modelling of Sheet Moulding Compound (SMC) composite materials, and to study the response of SMC composite structures under dynamic loading. The primary research objectives are thus to review classical and advanced material failure models, and to perform numerical simulation of the crash of composite structures using already available material models. Additionally, a new material model is to be developed for implementation into a commercially available finite element package. In parallel with the numerical simulation of the crasrung of an SMC composite structure, experimentation is performed which is used as a source of validation and comparison with the simulation. For this purpose a testing regime is introduced, which may be mirrored in simulation. As any material model requires initial experimental inputs, the purpose of experimentation is twofold, with testing required both for the quantification of the required model inputs and the basic material characterisation before simulation may begin, as well as for the proposed validation and comparison after the simulation has been carried out. Thus the design of the testing methodology, as well as the design, selection and fabrication of the testing equipment and the composite specimens and demonstrators, as well the actual testing itself, are necessary secondary requirements of the project. Once the testing regime has been facilitated and carried out, numerical simulation validation using already available composite material models may then be carried out at various levels. The results are then analysed and validated with the resultant justification of a new model being developed. The critical viewpoint to be delivered throughout is the need for theoretical formulations for material modelling to be extensively researched and validated in terms of their implementabilty and practicality, a key analysis seemingly missing in most technical write-ups. Such analyses are performed and discussed here, rughlighting the volume of additional work that is encompassed by such a study. / Thesis (M.Sc.Eng.)-University of Natal, Durban, 2003.

Indiana University-Purdue University Indianapolis (IUPUI) / Crashworthiness design is gaining more importance in the automotive industry due to high competition and tight safety norms. Further there is a need for light weight structures in the automotive design. Structural optimization in last two decades have been widely explored to improve existing designs or conceive new designs with better crashworthiness and reduced mass. Although many gradient based and heuristic methods for topology and topometry based crashworthiness design are available these days, most of them result in stiff structures that are suitable only for a set of vehicle components in which maximizing the energy absorption or minimizing the intrusion is the main concern. However, there are some other components in a vehicle structure that should have characteristics of both stiffness and flexibility. Moreover, the load paths within the structure and potential buckle modes also play an important role in efficient functioning of such components. For example, the front bumper, side frame rails, steering column, and occupant protection devices like the knee bolster should all exhibit controlled deformation and collapse behavior. This investigation introduces a methodology to design dynamically crushed thin-walled tubular structures for crashworthiness applications. Due to their low cost, high energy absorption efficiency, and capacity to withstand long strokes, thin-walled tubular structures are extensively used in the automotive industry. Tubular structures subjected to impact loading may undergo three modes of deformation: progressive crushing/buckling, dynamic plastic buckling, and global bending or Euler-type buckling. Of these, progressive buckling is the most desirable mode of collapse because it leads to a desirable deformation characteristic, low peak reaction force, and higher energy absorption efficiency. Progressive buckling is generally observed under pure axial loading; however, during an actual crash event, tubular structures are often subjected to oblique impact loads in which Euler-type buckling is the dominating mode of deformation. This undesired behavior severely reduces the energy absorption capability of the tubular structure. The design methodology presented in this paper relies on the ability of a compliant mechanism to transfer displacement and/or force from an input to desired output port locations. The suitable output port locations are utilized to enforce desired buckle zones, mitigating the natural Euler-type buckling effect. The problem addressed in this investigation is to find the thickness distribution of a thin-walled structure and the output port locations that maximizes the energy absorption while maintaining the peak reaction force at a prescribed limit. The underlying design for thickness distribution follows a uniform mutual potential energy density under a dynamic impact event. Nonlinear explicit finite element code LS-DYNA is used to simulate tubular structures under crash loading. Biologically inspired hybrid cellular automaton (HCA) method is used to drive the design process. Results are demonstrated on long straight and S-rail tubes subject to oblique loading, achieving progressive crushing in most cases.