No description available.

No description available.

Detonation-based propulsion systems are known for their high efficiency and energy release when compared to deflagrative systems, making them an ideal candidate in hypersonic propulsion applications. One such engine is the Oblique Detonation Wave (ODW) engine, which has a similar architecture to traditional scramjets but shortens the combustor and isolator to an anchored ODW after fuel injection. Previous research has focused on using a two-dimensional wedge to induce an ODW while limiting total losses through the combustor. In this configuration, a two-dimensional wedge-based architecture entails a rectangular duct, limiting potential inlet design and increasing overall skin friction. However, an inward-turning axisymmetric ODW wedge architecture, where a two-dimensional wedge is revolved around a central axis, has yet to be examined in detail. The work at present aims to investigate the fundamental physics required to predict the Oblique Shock Wave (OSW) for an inward-turning axisymmetric flow, which is critical for designing a circular ODW engine combustor. Multiple steady simulations of inviscid and ideal air at Mach 4, 6, and 8 were performed over a 1-inch wedge with wedge angles of 16°, 18°, and 20°. The radius of the inlet boundary was also varied between 1, 3, and 5 inches to examine the effect of increasing the blockage ratio. The results showed that the shock angle for an inward-turning axisymmetric flow was up to 8% steeper than the analytical, two-dimensional wedge solution. Additionally, it was found that the OSW diverged further from the two-dimensional solution when the blockage ratio was increased. These findings provide insight into the flow physics that must be considered when designing inward-turning axisymmetric ODW engines.

A computer code is developed using finite volume technique for solving steady twodimensional and axisymmetric compressible Euler and Navier-Stokes equations for internal flows by &ldquo / multi-block&rdquo / technique. For viscous flows, both laminar and turbulent flow properties can be used. Explicit one step second order accurate Lax-Wendroff scheme is used for time integration. Inviscid solutions are verified by comparing the results of test cases of a support project which was supported by ONERA/France for Turkey T-108, named &ldquo / 2-D Internal Flow Applications for Solid Propellant Rocket Motors&rdquo / . For laminar solutions, analytical flat plate solution is used for planar case and theoretical pipe flow solution is used for axisymmetric case for verification. Prandtl turbulent flow analogy is used in a flat plate solution to verify the turbulent viscosity calculation. The test cases solved with single-block code are compared with the ones solved with multi-block technique to verify the multi-block algorithm and good similarity is observed between single-block solutions and multi-block solutions. For the burning simulation of propellant of Solid Propellant Rocket Motors, injecting boundary is used. Finally, a segmented solid propellant rocket motor case is solved to show the multi-block algorithm&rsquo / s flexibility in solving complex geometries.

With the increased frequency of accidental and deliberate explosions, the response of civil infrastructure systems to blast loading has become a research topic of great interest. However, with the high cost and complex safety and logistical issues associated with live explosives testing, North American blast resistant construction standards (e.g. ASCE 59-11 & CSA S850-12) recommend the use of shock tubes to simulate blast loads and evaluate relevant structural response. This study aims first at developing a 2D axisymmetric shock tube model, implemented in ANSYS Fluent, a computational fluid dynamics (CFD) software, and then validating the model using the classical Sod’s shock tube problem solution, as well as available shock tube experimental test results. Subsequently, the developed model is compared to a more complex 3D model in terms of the pressure, velocity and gas density. The analysis results show that there is negligible difference between the two models for axisymmetric shock tube performance simulation. However, the 3D model is necessary to simulate non-axisymmetric shock tubes. The design of a shock tube depends on the intended application. As such, extensive analyses are performed in this study, using the developed 2D axisymmetric model, to evaluate the relationships between the blast wave characteristics and the shock tube design parameters. More specifically, the blast wave characteristics (e.g. peak reflected pressure, positive phase duration and the reflected impulse), were compared to the shock tube design parameters (e.g. the driver section pressure and length, the driven v section length, and perforation diameter and their locations). The results show that the peak reflected pressure increases as the driver pressure increases, while a decrease of the driven length increases the peak reflected pressure. In addition, the positive phase duration increases as both the driver length and driven length are increased. Finally, although shock tubes generally generate long positive phase durations, perforations located along the expansion section showed promising results in this study to generate short positive durations. Finally, the developed 2D axisymmetric model is used to optimize the dimensions of a proposed large-scale conical shock tube system developed for civil infrastructure blast response evaluation applications. The capabilities of this proposed shock tube system are further investigated by correlating its design parameters to a range of explosion threats identified by different hemispherical TNT charge weight and distance scenarios. / Thesis / Master of Applied Science (MASc)