Grab-bars and transfer poles are common sit-to-stand aids for older adults with mobility limitations. This study investigates differences in kinematics and kinetics in the lower limbs across different transfer pole configurations and positions. Configurations tested are a single pole, two poles and a pole with a horizontal grab-bar at near and far positions. Three-dimensional biomechanics were used to calculate kinetics and kinematics of the lower extremities. Forces were also recorded from the pole. This study found horizontal pole forces were an effective replacement for trunk generated horizontal momentum. Reduced vertical pole forces were applied by participants using the `far' poles which resulted in increases in non-dominant hip moments when using the single and double pole configurations. Horizontal pole use introduced non-dominant directed lateral COM trajectory throughout the movement. This coincided with increased horizontal forces in the dominant foot to balance moments about COM in the transverse plane as a motor control strategy.

Grab-bars and transfer poles are common sit-to-stand aids for older adults with mobility limitations. This study investigates differences in kinematics and kinetics in the lower limbs across different transfer pole configurations and positions. Configurations tested are a single pole, two poles and a pole with a horizontal grab-bar at near and far positions. Three-dimensional biomechanics were used to calculate kinetics and kinematics of the lower extremities. Forces were also recorded from the pole. This study found horizontal pole forces were an effective replacement for trunk generated horizontal momentum. Reduced vertical pole forces were applied by participants using the `far' poles which resulted in increases in non-dominant hip moments when using the single and double pole configurations. Horizontal pole use introduced non-dominant directed lateral COM trajectory throughout the movement. This coincided with increased horizontal forces in the dominant foot to balance moments about COM in the transverse plane as a motor control strategy.

Thesis (M.S.)--University of Hawaii at Manoa, 2005. / Includes bibliographical references (leaves 120-121). / xii, 282 leaves, bound ill. (some col.) 29 cm

Condition monitoring involves taking measurements on an induction motor while it is operating in order to detect faults. For this purpose normally a single sensor type, for example current is used to detect broken rotor bar using fault frequency components only under the full-load condition or a limited number of load cases. The correlations among the different types of sensors and their ability to diagnose single and multiple faults over a wide range of loads have not been the focused in previous research. Furthermore, to detect different faults in machines using any fault frequency components, it is important to investigate the variability in its amplitude to other effects apart from fault severity and load. This area has also often been neglected in the literature on condition monitoring. The stator current and axial flux have been widely used as suitable sensors for detecting different faults i.e. broken rotor bar and eccentricity faults in motors. Apart from detecting the broken rotor bar faults in generalized form, the use of instantaneous power signal has often been neglected in the literature condition monitoring. This thesis aims to improve machine condition monitoring and includes accurate and reliable detection of single and multiple faults (faults in the presence of other faults) in induction machines over a wide range of loads of rated output by using current, flux and instantaneous power as the best diagnostic medium. The research presents the following specific tasks: A comprehensive real database from non–invasive sensor measurements, i.e. vibration measurements, axial flux, 3-phase voltage, 3-phase current and speed measurements of induction motor is obtained by using laboratory testing on a large set of identical motors with different single and multiple faults. Means for introducing these faults of varying severity have been developed for this study. The collected data from the studied machines has been analysed using a custom-written analysis programme to detect the severity of different faults in the machines. This helps to improve the accuracy and reliability in detecting of single and multiple faults in motors using fault frequency components from current, axial flux and instantaneous power spectra. This research emphasises the importance of instantaneous power as a medium of detecting different single and multiple faults in induction motor under varying load conditions. This enables the possibility of obtaining accurate and reliable diagnostic medium to detect different faults existing in machines, which is vital in providing a new direction for future studies into condition monitoring. Another feature of this report is to check the variability in healthy motors due to: test repeatability, difference between nominally identical motors, and differences between the phases of the same motor. This has been achieved by conducting extensive series of laboratory tests to examine fault frequency amplitudes versus fault severity, load, and other factors such as test repeatability and machine phases. The information about the variations in the amplitudes of the fault frequency components is used to check the accuracy and reliability of the experimental set-up, which is necessary for the practical application of the results to reliably detect the different faults in the machines reliably. Finally, this study also considers the detection of eccentricity faults using fault frequency amplitudes as a function of average eccentricity, instead of as a function of load under different levels of loading. This has not been reported in previous studies. / http://proxy.library.adelaide.edu.au/login?url= http://library.adelaide.edu.au/cgi-bin/Pwebrecon.cgi?BBID=1298314 / Thesis (Ph.D.)-- University of Adelaide, School of Electrical and Electronic Engineering, 2008

Thesis (M.S.)--University of Missouri-Columbia, 2007. / The entire dissertation/thesis text is included in the research.pdf file; the official abstract appears in the short.pdf file (which also appears in the research.pdf); a non-technical general description, or public abstract, appears in the public.pdf file. Title from title screen of research.pdf file (viewed on January 8, 2008) Includes bibliographical references.

Thesis (M.S.)--Oregon State University, 2008. / Printout. Includes bibliographical references (leaves 36-41). Also available on the World Wide Web.

Thesis (M.S.)--Rochester Institute of Technology, 1993. / Typescript. Includes bibliographical references (leaves 34-35).

Thesis (Ph. D.)--University of Texas at Austin, 2003. / Vita. Includes bibliographical references. Available also from UMI Company.

Thesis (Ph. D.)--University of Texas at Austin, 2002. / Vita. Includes bibliographical references. Available also from UMI Company.

Thesis (Ph. D.)--Oregon State University, 2010. / Printout. Includes bibliographical references (leaves 121-131). Also available on the World Wide Web.