Disertační práce se věnuje problematice obecných koncentrátorů napětí v anisotropních prostředích. Zejména se jedná o problém trhlin končících na rozhraní dvou různých materiálů, či problém obecného více-materiálového klínu. Cílem práce je vytvořit komplexní nástroj pro posuzování obecných koncetrátorů napětí tj, popis pole napětí v jeho okolí, zahrnutí případného vlivu přemostění trhliny do výsledného pole napětí a definici lomových kritérií pro obecný koncentrátor v anisotropním prostředí. U popisu pole napětí je využit tzv. Lechnického-Strohův formalismus a technika spojitě rozložených dislokací využívající teorii komplexních potenciálů. V práci je rovněž široce uplatněn tzv. dvoustavový "psí"-integrál (pro výpočet různých součinitelů asymptotického rozvoje pro napětí), založený na Bettiho recipročním teorému v kombinaci s metodou konečných prvků. Pro formulaci lomových kritérií je použita teorie tzv. „konečné lomové mechaniky“ a teorie sdružených asymptotických rozvojů. Studován je především vztah mezi ohybem trhliny podél rozhraní a její případnou pentrací do základního materiálu. Veškeré potřebné výpočty jsou prováděny v matematických softwarech MAPLE 10.0, MATLAB 7.1 a konečnoprvkovém systému ANSYS 10.0.

Components of turbines, combustion chambers, multi-layered electronic packaging structures and nuclear reactors are subjected to transient thermal loads during their service life. In the presence of a discontinuity like crack or dislocation, the thermal load creates high temperature gradient, which in turn causes the stress intensification at the crack tips. If proper attention is not paid in the design and maintenance of components on this high stress in the vicinity of crack tips, it may lead to instability in the system and decrease in the service life. The concepts of thermal fracture mechanics and its major parameter called transient thermal stress intensity factors can greatly help in the assessment of stability and residual life prediction of such structures. The evaluation of thermal stress intensity factors becomes computationally difficult when the body constitutes of two different materials or is non-homogenous or made of composites. Fracture at bi-material interface is different from its homogenous counterpart because of mixed mode stress condition that prevails at the crack tip even when the geometry is symmetric and loading unidirectional. Because of this, the mode 1 and mode 2 stress intensity factors can not be decoupled to represent tension and shear stress fields as can be done in the case of homogeneous materials. Mathematically, the stress intensity factors at bi-material interfaces are complex due to oscillatory singularity that exists at the crack tip. Although plenty of literature is available for bi-material systems subjected to mechanical loads, very little information is available on problems related to thermal loads. Besides, problems related to transient thermal loads need special attention, since no thermal weight functions are available and the existing methods are computationally expensive. Therefore, the present investigation has been undertaken to develop computational and analytical approaches for obtaining the Mode 1 and Mode 2 stress intensity factors for bi-material interface crack problems using conservation of energy principle in conjunction with the weight function approach for various kinds of thermal loads. In the beginning of the studies, a method to extract the Mode 1 and Mode 2 stress intensity factors for bi-material interface crack subjected to mechanical load is proposed using the concept of Jk integrals. This is extended to thermal loads using J2 line integral and J2 domain integral. Furthermore, weight functions are analytically derived for thermal bi-material stress intensity factors and a computational scheme is developed. These methods are validated for several benchmark problems with known solutions.

The presented diploma thesis concerns linear fracture mechanics and deals with determination of the stress intensity factor of the finite crack, which is located in the vicinity of the bimaterial interface, solved by the distributed dislocation technique and theory of complex potencials. The work is possible to devide into three parts. The first part includes basic concepts of the linear fracture mechanics and is also dedicated to the mechanics of composite materials. The second part deals with the determination of the stress intensity factor from solving singular integral equation formulated by Bueckner's principle and the distributed dislocation technique. The third part includes the specific configuration of the crack with respect to the bimaterial interface and the solution, which is compared with results obtained from the FE analysis.

The presented diploma thesis deals with a problem of a generalized stress intensity factor determination and a consecutive study of stress distribution around the bimaterial notch tip, combining analytical and numerical methods. This task is possible to sectionalize into three parts. The first part is dedicated to the fundamentals of the linear fracture mechanics and the mechanics of composite materials. The second part deals with methods of anisotropic plane elasticity solution. Pursuant to the solution the computational models in the third part are created. The first model makes for determination of a singularity exponent eigenvalue by dint of Lekhnitskii-Eshelby-Stroh formalism. The second model makes for determination of the generalized stress intensity factor using psi-integral method, which is based on the Betti reciprocal theorem. All needed calculation are performed in the software ANSYS 12, Maple 12 and Silverforst FTN95. Results will be compared with the values obtained from a direct method of the generalised stress intensity factor determination.

Disertační práce se věnuje problematice obecných koncentrátorů napětí v anisotropních prostředích. Zejména se jedná o problém trhlin končících na rozhraní dvou různých materiálů, či problém obecného více-materiálového klínu. Cílem práce je vytvořit komplexní nástroj pro posuzování obecných koncetrátorů napětí tj, popis pole napětí v jeho okolí, zahrnutí případného vlivu přemostění trhliny do výsledného pole napětí a definici lomových kritérií pro obecný koncentrátor v anisotropním prostředí. U popisu pole napětí je využit tzv. Lechnického-Strohův formalismus a technika spojitě rozložených dislokací využívající teorii komplexních potenciálů. V práci je rovněž široce uplatněn tzv. dvoustavový "psí"-integrál (pro výpočet různých součinitelů asymptotického rozvoje pro napětí), založený na Bettiho recipročním teorému v kombinaci s metodou konečných prvků. Pro formulaci lomových kritérií je použita teorie tzv. „konečné lomové mechaniky“ a teorie sdružených asymptotických rozvojů. Studován je především vztah mezi ohybem trhliny podél rozhraní a její případnou pentrací do základního materiálu. Veškeré potřebné výpočty jsou prováděny v matematických softwarech MAPLE 10.0, MATLAB 7.1 a konečnoprvkovém systému ANSYS 10.0.

Three testing methods are proposed to characterize properties of fuel cell materials that affect the mechanical durability of proton exchange membranes (PEMs). The first two methods involved measuring the in-plane biaxial strength of PEMs and the biaxial hygrothermal stresses that occur in PEMs during hygrothermal cycles. The third method investigated the nonuniform thickness and compressibility of gas diffusion media which can lead to concentrated compressive stresses in the PEM in the through-plane direction. Fatigue and creep to leak tests using multi-cell pressure-loaded blister fixtures were conducted to obtain the lifetimes of PEMs before reaching a threshold value of gas leakage. These tests are believed to be more relevant than quasi-static uniaxial tensile to rupture tests because of the introduction of biaxial cyclic and sustained loading and the use of gas leakage as the failure criterion. They also have advantages over relative humidity cycling test because of the controllable mechanical loading. Nafion® NRE-211 membrane was tested at three different temperatures and the time-temperature superposition principle was used to construct a stress-lifetime master curve. Tested at 90°C, extruded Ion Power® N111-IP membrane was found to have longer lifetime than Gore™-Select® 57 and Nafion NRE-211 membranes under the same blister pressure profiles. Bimaterial specimens fabricated by bonding a piece of PEM to a substrate material were used to measure the hygral stresses, compressive and tensile, in the PEM during relative humidity cycles. The substrate material and its thickness were carefully chosen so that stresses in the PEM could be obtained directly from the curvature of the bimaterial specimen without knowing the constitutive properties of the PEM. Three commercial PEMs were tested at 80°C by cycling the relative humidity between 90% and 0% and by drying the membrane to 0%RH after submersion in liquid water. Stress histories for all three membranes show strong time-dependencies and Nafion® NRE-211 exhibited the largest tensile stress upon drying. Besides in-plane stresses, hard spots in gas diffusion media (GDM) can locally overcompress PEMs in the out-of-plane direction and cause electrical shorting. In this study, GDM samples sealed with an impermeable Kapton® film on the surface were compressed with uniform air pressure and the nonuniform displacement field was measured with a three-dimensional digital image correlation technique. Hard spots as a result of the nonuniform thickness and compressibility of the GDM were found and their severities as stress risers are evident. Locally, a nominal platen compression (similar to bipolar plate land compression) of 0.68 MPa can lead to compressive stress as large as 2.30 MPa in various hard spots that are in the order of 100s µm to 1 mm in size. / Ph. D.