Spelling suggestions: "subject:"bloco estrutural dde concreto"" "subject:"bloco estrutural dee concreto""
1 |
AVALIAÇÃO DO DESEMPENHO TÉRMICO EM EDIFICAÇÕES DE BLOCOS ESTRUTURAIS CERÂMICOS E DE BLOCOS ESTRUTURAIS DE CONCRETO PARA A ZONA BIOCLIMÁTICA 2 BRASILEIRA / EVALUATION OF THE THERMAL PERFORMANCE IN BUILDINGS WITH CLAY STRUCTURAL BLOCK AND CONCRETE STRUCTURAL BLOCK FOR THE BRAZILIAN BIOCLIMATIC ZONE 2Kappaun, Kamila 18 September 2012 (has links)
Structural masonry has been used more and more in Brazil, but this technology
has limitations on research which report its thermal behavior. In Rio Grande do Sul, the
clay structural block is the most widely used, while in Brazil as a whole, concrete
structural blocks are more popular. Thermally speaking, it is not known which block is
better suited for the Brazilian bioclimatic zone 2. The thermal performance of two
structures built with structural masonry, one with clay and one with concrete, is analyzed
in this thesis. Initially, the values for the thermal characteristics of both types of closure
were defined, to contrast the differences among them, with the intent to thermally
analyze both buildings. The thermal transmittance, the thermal capacity, and the thermal
delay were calculated. In loco measurements were made in buildings with the same floor
plan, solar orientation, and implementation, but which were built with different structural
blocks. The analyses contemplated different parameters which could have influenced
the results, such as the influence of the ceiling and solar orientation. The results from
both buildings were compared with the measured external temperatures, and also
analyzed with regards to the observance of a standardized thermal performance. / A alvenaria estrutural vem sendo cada vez mais usada no Brasil, mas essa
tecnologia tem limitações de pesquisas que relatem seu comportamento térmico.
Enquanto o bloco estrutural de concreto é o mais usado em todo o Brasil, no Rio
Grande do Sul o bloco estrutural mais utilizado é o cerâmico. Porém, do ponto de vista
térmico, não há indicação de qual bloco seria o mais indicado para a zona bioclimática
2 brasileira. Neste trabalho é analisado o desempenho térmico de duas edificações
construídas em alvenaria estrutural, uma com bloco estrutural cerâmico e outra com
bloco estrutural de concreto. Inicialmente foram definidos os valores das características
térmicas dos dois tipos de fechamentos, para evidenciar as diferenças dos mesmos,
visando a análise térmica das duas edificações. Foram calculados a transmitância
térmica, a capacidade térmica e o atraso térmico. Foram também feitas medições in
loco nestas duas edificações, que apresentam mesma planta baixa, orientação solar e
implantação e que foram construídas com dois diferentes blocos estruturais. As análises
contemplaram parâmetros que poderiam influenciar nos resultados, como a influência
da cobertura e da orientação solar. Os resultados foram analisados comparativamente
entre as duas diferentes edificações e com as temperaturas medidas externamente, e
também analisadas quanto ao cumprimento do desempenho térmico conforme
normatizado.
|
2 |
Contribuição para a otimização de traços de concreto utilizados na produção de blocos estruturaisFelipe, Alexsandro dos Santos [UNESP] 01 February 2010 (has links) (PDF)
Made available in DSpace on 2014-06-11T19:25:21Z (GMT). No. of bitstreams: 0
Previous issue date: 2010-02-01Bitstream added on 2014-06-13T20:53:08Z : No. of bitstreams: 1
felipe_as_me_ilha.pdf: 2392820 bytes, checksum: 9c6e04fef232018e3760dee715984441 (MD5) / Universidade Estadual Paulista (UNESP) / Diante do grande crescimento da alvenaria estrutural no país, muitas fábricas de blocos de concreto vieram por necessidade, buscar por otimizações do seu processo produtivo, visto que, projetos mais arrojados, acabam exigindo maiores controles de qualidade. A proposta deste estudo é melhorar a produção destes artefatos de concreto por meio de otimizações simples que reduzem o custo e garantem uma produção eficiente na fábrica. Estudar a fundo os vários parâmetros de formação de um traço de concreto seco, tais como coesão, textura, energias de adensamento e resistência à compressão axial, todos os fenômenos dependentes entre si, torna-se muito complexo se avaliado em um único trabalho. No entanto, propor um estudo que colete informações apresentadas por vários autores, facilita na otimização e criação de uma pesquisa que possa contribuir na dosagem para concretos secos, em especial, na fabricação de blocos estruturais. Neste estudo, adaptaram-se para laboratório alguns equipamentos de uso comum para confecção destes artefatos de concreto, possibilitando a correlação direta de corpos de prova cilíndricos com os blocos. Uma das adaptações é o estudo baseado na padronização da energia de compactação, proporcionada pelo equipamento para ensaios de mini-proctor, simulando assim, a máquina vibro-prensa. Outras correlações como coesão e resistência à compressão, também foram possíveis de obter no laboratório, reduzindo então, as interferências constantes no processo produtivo da fábrica, ocasião verificada em vários outros estudos. Diante do exposto, foi possível avaliar com boa segurança os resultados. O estudo foi desenvolvido em três etapas, sempre buscando a maior massa específica seca compactada da mistura de agregados, inicialmente na primeira etapa, foi utilizado somente dois agregados (areia fina e pedrisco), conforme... / Given the substantial growth of structural masonry in Brazil, many concrete block companies have seen the need to optimize their production process, since more challenging projects require greater quality control. This study proposes to improve the production of concrete artifacts by means of simple optimizations that reduce costs and ensure the company’s efficient production. Studying in depth the various parameters of the formation of dry concrete trace, such as cohesion, texture, density energy and axial compressive strength, all the particularities interdependent on one another become very complex when assessed in a single study. However, proposing a study that collects the information submitted by various authors, expedites optimizing and creating a research study which may assist in improving the dosage for dried concrete, particularly in the manufacture of structural blocks. In this study, some commonly used manufacturing equipment, such as concrete artifacts, were laboratory-adapted, enabling a direct correlation of the cylindrical specimens with the blocks. One of the adjustments is the study based on the standardization of compaction energy, provided by the mini-proctor testing equipment, thus simulating the vibro press machine. Other correlations such as cohesion and compressive strength were also obtained in the laboratory, therefore reducing the constant interferences in the plant’s production process, observed in many other studies. In this manner, it was possible to reliably assess the results. The study was conducted in three stages, always seeking the highest compressed dry specific mass of the mixture of aggregates. In the first stage, only two aggregates were used (fine sand and pebbles), commonly used at the plant. The second stage included adding the coarse sand and stone powder to correct the lack of resistance promoted by the high amount of fine sand from... (Complete abstract click electronic access below)
|
Page generated in 0.1067 seconds