Fouling of tube bundles in boilers on the flue gas side affects not only the service life, but also the boiler heat output and increases maintenance and operating costs. Therefore, it is necessary to minimize or completely eliminate this process. This thesis focuses on comparison of the service life and the heat output of the tube bundles with and without deposit in the coal fired boiler. Simulations of flue gas flow in area of tube bundles with and without deposit are performed using ANSYS Fluent software, which shows that the surface of tube bundles with deposit is much less heated than the surface without deposit. The thermal loads of tubes obtained by the CFD analysis are applied to the model, which is created in the program ANSYS Mechanical, where the calculation of the temperature field in the cross section of the pipe is realized. The effect of fouling on creep life and heat output is then evaluated based on simulation results. The results show that fouling increases creep life, but significantly reduces heat output of heavily fouled tubes. Hence the flue gas flows at a higher temperature to the rest of the tube bundle, and the service life of those tubes will therefore probably decrease.

The topic of this diploma thesis is to design the co-firing of blast furnace gas and coke-oven gas. First, the stoichiometric calculation for the gas mixture was made. It is followed with the determination of basic measures of heating surfaces and with their thermal calculation. The part of the work is also the drawing documentation of the boiler.

This master's thesis deals with design of steam grade boiler for burning refuse derived fuel with power output of 70 t/h. The assignment contain a requiered steam output parameters and composition of fuel. From this composition of fuel is calculated stoichiometric calculation, the heat loss and the efficiency of boiler. After that follows a design of the boiler with closer design of each of the heating surfaces.

This thesis deals with the design grate boilers with natural circulation for the combustion of contaminated biomass. The boiler output is output 45 t/h. Produced superheated steam with the output parameters of 440 °C 4,2 at MPa feed water temperature 115 °C. The stoichiometric calculations and the thermal calculation are based on the specified fuel composition. Thanks to this, the basic dimensional design of the boiler and its efficiency are determined. Calculation of this work focuses mainly on thermal calculations and dimensional design of individual heat transfer surfaces. Basic drawing of the boiler is available in the attachment of the thesis.

This master’s thesis deals with the possibility of increasing efficiency of energy blocks with combustion engines by the combination of the Sabat and Clausius-Rankine cycle into the combined cycle. In the thesis is briefly described the principle of the function of the auxiliary device, which can increase the efficiency of the combustion engine. This device, which consists of a waste heat boiler and two turbine modules, is designed using calculations. Both turbine modules are prepared with drawing documentation and there are described important structural elements. Each key part of the thesis is given by a brief theory, so the basic theory of combustion engines, waste heat boilers and steam turbine are described.

The master’s thesis deals with the design of a boiler for RDF combustion, based on the required power output and superheated steam parameters. The first part of the thesis focuses on combustion calculations. Boiler efficiency is also calculated in this chapter, using the heat balance efficiency method. The main part of the thesis consists of dimensional design and heat transfer calculations. The precision of the calculations is checked at the end of the thesis along with the chlorine corrosion, which is considered because of the higher amount of chlorine in the fuel. The thesis comes with a basic schematic of the designed boiler.

The first part of the thesis deals with the issue of indoor climate in school buildings. The second part deals with the design of the heating system in the extension of the primary school, including the design of the source and the reconstruction of the source for the existing building in a variant solution. The last part of the thesis is devoted to experimental measurement of indoor air quality in elementary school.

In this thesis, heating system with hybrid control of the heating intended for houses is proposed. The system is primarily prepared for storage tank and multiple heat sources.

The aim of the thesis is a design of a grate steam boiler with capacity of 35 t/h and output steam parameters with temperature 430 °C and pressure 4,1 MPa. The first part of the thesis deals with stoichiometric calculations and boiler efficiency. The theses mainly focuses on the heat transfer calculation and the geometric design of individual heat transfer surfaces. The specifics of fuel are taken into consideration. The drawing of the basic boiler scheme is a part of the thesis.

This thesis deals with a design of a steam boiler combusting natural gas. It consists of stoichiometric calculation, determination of boiler efficiency, thermal calculations and determining geometric parameters of the boiler and its heat transfer surfaces. The results are verified by the heat balance of the boiler.