Development of continuity between precast prestressed bridge girders by post-tensioning the insitu top slab In the regions of hogging moment is a relatively new technique which forms the basis for this research study. Compared to the more conventional method of using reinforcing steel in the slab over the interior supports, prestressed slabs will ensure a crack free more durable bridge deck, and will therefore reduce the maintenance costs. The effect that such a slab has on flexural and shear behaviour of the bridge deck has been studied both analytically and experimentally by considering composite beams based on M-8 standard precast beam section. Comparison of the design of bridge decks with a prestressed slab and a reinforced concrete slab indicated that a partially prestressed slab with a prestress considering up to 50% of the live load will ensure the slab remains crack free under total service load. Although secondary effects and the two stage construction of such a slab tend to increase the prestress requirement for the slab, the same two effects considerably reduce the positive midspan moments, resulting in a decrease in the prestress required in the precast beams (and thus a possible increase in the span range) for given standard precast beam sections. The experimental investigation consisted of testing eleven 1/3-scale M-8 continuous composite beams in two series, Series-A and Series-B. Series A, in which three beams were tested as double cantilevers was planned to study the effects of prestressed slab on overall flexural behaviour. A considerable improvement in crack control under service loads and a higher ratio of measured to calculated ultimate moment capacity was obtained in beams with a prestressed slab. The continuity developed using insitu prestressed slabs was very effective at all levels of loading. Recommendations have been made for the flexural design of continuous bridge decks with this type of prestressed slabs. In Series B, effect of prestressed slabs on shear strength at the continuity connection has been studied. A considerable increase in web shear cracking load was obtained for beams with prestressed slabs, resulting in a decrease In the amount of shear reinforcement required for such beams. The different methods of predicting web shear cracking strength and web crushing strength according to current design codes were compared with experimental values, and based on the results, recommendations for the design for vertical shear of composite beams subjected to hogging moments have been made.

The damaging effects of hurricane landfall on US coastal bridges have been studied using physical model testing. Hurricane bridge damage and failure susceptibility has become very evident, especially during hurricane seasons 2004 and 2005 in the Gulf of Mexico. The combination of storm surge and high waves caused by a hurricane can produce substantial loads on bridge decks leading to complete bridge failure. Several theoretical methods have been developed to estimate these forces but have not been tested in a laboratory setting for a typical bridge section. Experiments were done using a large-scale 3-D wave basin located at the Haynes Coastal Engineering Laboratory at Texas A&M University to provide estimates of the horizontal and vertical forces for several conditions to compare with the forces predicted with the existing models. The wave force results show no strong correlation between the actual force measured and the predicted force of existing theoretical methods. A new method is derived from the existing theoretical methods. This model shows a strong correlation with both the measured horizontal and vertical forces.

The damaging effects of hurricane landfall on US coastal bridges have been studied using physical model testing. Hurricane bridge damage and failure susceptibility has become very evident, especially during hurricane seasons 2004 and 2005 in the Gulf of Mexico. The combination of storm surge and high waves caused by a hurricane can produce substantial loads on bridge decks leading to complete bridge failure. Several theoretical methods have been developed to estimate these forces but have not been tested in a laboratory setting for a typical bridge section. Experiments were done using a large-scale 3-D wave basin located at the Haynes Coastal Engineering Laboratory at Texas A&M University to provide estimates of the horizontal and vertical forces for several conditions to compare with the forces predicted with the existing models. The wave force results show no strong correlation between the actual force measured and the predicted force of existing theoretical methods. A new method is derived from the existing theoretical methods. This model shows a strong correlation with both the measured horizontal and vertical forces.

No description available.

Chloride-induced corrosion of reinforcing steel is widely accepted as the primary cause of premature deterioration in concrete bridge decks (Brown, M.C., 2002). Since linear cracking in concrete cover can potentially accelerate chloride ingress to the depth of the reinforcing steel, there is reason to believe that severity of deck cracking can significantly influence the time to first repair and/or rehabilitation of the bridge deck. Surface width, orientation, and length of cracks in 38 Virginia bridge decks were investigated in order to characterize the general distribution of deck cracking in the commonwealth of Virginia. Crack data was correlated to structural/material design parameters and environmental exposure conditions in order to determine significant predictor-response relationships. The majority of surveyed bridge decks were divided into four classifications of deck type based on superstructure type and construction era, either 1968-1971 or 1984-1991. Surveyed bridge decks that did not fit into any of the four classifications were used to form more generalized subsets. These larger subsets were used to determine if significant influence factors could be translated to broader classifications of bridge decks. Transverse beam spacing, annual average daily truck traffic (AADTT), resistivity of the deck concrete, chloride exposure, and the percentage of concrete clear cover depths less than or equal to 38mm (1.5 in) were all determined to have a significant correlation with linear deck cracking. / Master of Science

Since the use of epoxy coated steel has become mandatory starting in the 1980s, recent studies have shown that epoxy coating does not prevent corrosion, but instead will debond from the steel reinforcement in as little as 4 years (Weyers RE et al, 1998) allowing instead a much more insidious form of corrosion to take place known as crevice corrosion. Therefore, it is important to determine if the nondestructive corrosion activity detection methods are applicable to ECR as well as institute guidelines for interpreting the results. Since the corrosion of reinforcing steel is directly responsible for damage to concrete structures, it is surprising that nondestructive corrosion assessment methods are not part of regular bridge inspection programs such as PONTIS and NBIS. Instead, the inspection and bridge rating guidelines of federally mandated programs such as NBIS are so vague as to allow for a relatively subjective application by the field inspectors. Clear cover depths, resistance, corrosion potentials, linear polarization data, as well as environmental exposure and structural data were collected from a sample of 38 bridge decks in the Commonwealth of Virginia. These structures were further divided in three subsets: bridge decks with a specified w/c ratio of 0.47, bridge decks with a specified w/c ratio of 0.45 and bridge decks with a specified w/cm ratio of 0.45. This data was then correlated to determine which parameters are the most influential in the assignment of NBIS condition rating. Relationships between the non-destructive test parameters were also examined to determine if corrosion potentials and linear polarization are applicable to epoxy coated steel. Based on comparisons of measurements distributions, there is an indication that corrosion potential tests may be applicable to structures reinforced with epoxy coated steel. Furthermore, these conclusions are supported by statistical correlations between resistivity, half cell potentials and linear polarization measurements. Unfortunately, although apparently applicable, as of now there are no guidelines to interpret the results. Based on the linear corrosion current density data collected, no conclusion can be drawn regarding the applicability of the linear polarization test. As far as the NBIS deck rating is concerned, since the inspection guidelines are so vague, age becomes a very easy and attractive factor to the field personnel to rely on. However, this conclusion is far from definitive since the very large majority of structures used in this particular study had only two rating values out of theoretically ten and realistically five possible rating values. / Master of Science

The purpose of this research was to evaluate the performance history of continuous bridge decks in the State of Georgia, to determine why the current design detail works, to recommend a new design detail if necessary, and to recommend the maximum and/or optimum lengths of continuous bridge decks. The continuous bridge decks have continuous reinforcement over the junction of two edge beams with a construction joint for crack control. The current technical literature and current practices and design procedures were synthesized and summarized. GDOT maintenance reports were reviewed, and field evaluations were conducted to determine the performance of the continuous deck detail. The effects of bridge movement due to thermal strains, shrinkage, and live loads were considered in the analytical studies to better understand the demands placed on the GDOT continuous deck detail. A summary of the design and length recommendations was provided upon completion of the research.

The objectives of this research were to 1) investigate bridge deck condition assessment methods used in the field and laboratory, methods of managing bridge decks, and methods for estimating remaining bridge deck service life using computer models through a comprehensive literature review on these subjects; 2) collect and analyze field data from representative concrete bridge decks in Utah; and 3) develop a decision tree for concrete bridge deck management in Utah. As a result of the literature review performed for objective 1, a synthesis of existing information about condition assessment, bridge deck preservation and rehabilitation, bridge deck reconstruction, and estimating remaining service life using computer models was compiled. For objective 2, 15 bridge decks were strategically selected for testing in this research. Five bridge decks had bare concrete surfaces, five bridge decks had asphalt overlays, and five bridge decks had polymer overlays. Bridge deck testing included site layout, cover depth measurement, chloride concentration testing, chain dragging, half-cell potential testing, Schmidt rebound hammer testing, impact-echo testing, and vertical electrical impedance testing. Two-sample t-tests were performed to investigate the effects of selected bridge deck features, including polymer overlay application, deck age at polymer overlay application, overlay age, asphalt overlay application with and without a membrane, stay-in-place metal forms (SIPMFs), SIPMF removal, internally cured concrete, and use of an automatic deck deicing system. For objective 3, condition assessment methods were described in terms of test type, factors evaluated, equipment cost, data collection speed, required expertise, and traffic control for each method. Unit costs, expected treatment service life estimates, and factors addressed for the preservation, rehabilitation, and reconstruction methods most commonly used by the Utah Department of Transportation (UDOT) were also summarized. Bridge deck testing results were supplemented with information about current bridge deck management practices and treatment costs obtained from UDOT, as well as information about condition assessment and expected treatment service life, to develop a decision tree for concrete bridge deck management. Based on the results of field work and statistical analyses, placing an overlay within a year after construction is recommended. Removing SIPMFs after a deck age greater than 18 years is not likely to be effective at reversing the adverse effects of the SIPMFs on bridge deck condition and is not recommended. Bridge deck construction using internally cured concrete is not recommended for protecting against rebar corrosion. To the extent that excluding an automatic deck deicing system does not compromise public safety, automatic deck deicing systems are not recommended. To supplement the typical corrosion initiation threshold of 2.0 lb Cl-/yd3 of concrete for black bar, a corrosion initiation threshold of 8.0 lb Cl-/yd3 of concrete is recommended in this research for bridge decks with intact epoxy-coated rebar. For chloride concentrations less than 20 lb Cl-/yd3 of concrete as measured between reinforcing bars, an increase of up to 70 percent should be applied to estimate the corresponding chloride concentration of the concrete in direct contact with the rebar. The decision tree developed in this research includes 10 junctions and seven recommended treatments. The junctions require the user to address questions about surface type, degree of protection against water and chloride ion ingress, degree of deterioration, and years of additional service life needed; the answers lead to selection of treatment options ranging from repairing an overlay to full-depth bridge deck reconstruction. Revisions to the decision tree should be incorporated as additional methods, data, treatments, or other relevant information become available.

The objectives of this research were to 1) investigate bridge deck condition assessment methods used in the field and laboratory, methods of managing bridge decks, and methods for estimating remaining bridge deck service life using computer models through a comprehensive literature review on these subjects; 2) collect and analyze field data from representative concrete bridge decks in Utah; and 3) develop a decision tree for concrete bridge deck management in Utah. As a result of the literature review performed for objective 1, a synthesis of existing information about condition assessment, bridge deck preservation and rehabilitation, bridge deck reconstruction, and estimating remaining service life using computer models was compiled. For objective 2, 15 bridge decks were strategically selected for testing in this research. Five bridge decks had bare concrete surfaces, five bridge decks had asphalt overlays, and five bridge decks had polymer overlays. Bridge deck testing included site layout, cover depth measurement, chloride concentration testing, chain dragging, half-cell potential testing, Schmidt rebound hammer testing, impact-echo testing, and vertical electrical impedance testing. Two-sample t-tests were performed to investigate the effects of selected bridge deck features, including polymer overlay application, deck age at polymer overlay application, overlay age, asphalt overlay application with and without a membrane, stay-in-place metal forms (SIPMFs), SIPMF removal, internally cured concrete, and use of an automatic deck deicing system. For objective 3, condition assessment methods were described in terms of test type, factors evaluated, equipment cost, data collection speed, required expertise, and traffic control for each method. Unit costs, expected treatment service life estimates, and factors addressed for the preservation, rehabilitation, and reconstruction methods most commonly used by the Utah Department of Transportation (UDOT) were also summarized. Bridge deck testing results were supplemented with information about current bridge deck management practices and treatment costs obtained from UDOT, as well as information about condition assessment and expected treatment service life, to develop a decision tree for concrete bridge deck management. Based on the results of field work and statistical analyses, placing an overlay within a year after construction is recommended. Removing SIPMFs after a deck age greater than 18 years is not likely to be effective at reversing the adverse effects of the SIPMFs on bridge deck condition and is not recommended. Bridge deck construction using internally cured concrete is not recommended for protecting against rebar corrosion. To the extent that excluding an automatic deck deicing system does not compromise public safety, automatic deck deicing systems are not recommended. To supplement the typical corrosion initiation threshold of 2.0 lb Cl-/yd3 of concrete for black bar, a corrosion initiation threshold of 8.0 lb Cl-/yd3 of concrete is recommended in this research for bridge decks with intact epoxy-coated rebar. For chloride concentrations less than 20 lb Cl-/yd3 of concrete as measured between reinforcing bars, an increase of up to 70 percent should be applied to estimate the corresponding chloride concentration of the concrete in direct contact with the rebar. The decision tree developed in this research includes 10 junctions and seven recommended treatments. The junctions require the user to address questions about surface type, degree of protection against water and chloride ion ingress, degree of deterioration, and years of additional service life needed; the answers lead to selection of treatment options ranging from repairing an overlay to full-depth bridge deck reconstruction. Revisions to the decision tree should be incorporated as additional methods, data, treatments, or other relevant information become available.

Three series of tests were conducted on a sandwich plate bridge deck, which consisted of two steel plates and an elastomer core. The first series of testing was conducted by applying a static load on a full scale sandwich plate bridge deck panel. Local strains and deflections were measured to determine the panel's behavior under two loading conditions. Next, fatigue tests were performed on the longitudinal weld between two sandwich plate panels. Two connections were tested to 10 million cycles, one connection was tested to 5 million cycles, and one connection was tested to 100,000 cycles. The fatigue class of the weld was determined and an S-N curve was created for the longitudinal weld group. Finally, a series of experiments was performed on a half scale continuous bridge deck specimen. The maximum positive and negative flexural bending moments were calculated and the torsional properties were examined. Finite element models were created for every load case in a given test series to predict local strains and deflections. All finite element analyses were preformed by Intelligent Engineering, Ltd. A comparison of measured values and analytical values was preformed for each test series. Most measured values were within five to ten percent of the predicted values. Shear lag in the half scale bridge was studied, and an effective width to be used for design purposes was determined. The effective width of the half scale simple span sandwich plate bridge deck was determined to be the physical width. Finally, supplemental research is recommended and conclusions are drawn. / Master of Science