No description available.

Slender structures are elegant aesthetically. The insufficiency in knowledge of the real resistance to buckling of very slender reinforced concrete columns leads to an exaggeration of the sizes of the columns. _The examples of concrete compression members cited and constructed in Industry on a global basis suggest that very slender columns have inherent safety both from the point of view of the ultimate strength and stability. The strengths of columns given. by the British codes would seem to be exceeded by many of the long slender reinforced concrete columns and struts which have been used Internationally. Both the theoretical and the experimental short term investigations have been carried out to establish the behaviour of hinged, very slender reinforced concrete columns at various stages'of axial loading. Forty three very slender reinforced concrete columns of two different square cross sections with two sizes of longitudinal reinforcements with lateral ties were cast. Slenderness rates, L A, were varied from 30 to 79. Special factors were obtained to relate the actual modulus of elasticity of concrete in columns at buckling failure to a knowledge of the initial modulus of elasticity of concrete in control cylinder specimens. Both theoretical and experimental graphs of load against moment, made dimensionless for critical sections of columns have been obtained. Dimensionless load-moment interaction diagrams using material failure as the criterion have been superimposed on these graphs to show considerable inherent material strength of the tested columns near buckling collapse failures. A theory using the fundamental approach has, been developed to predict the deflected shape and moments along the, heights of the columns at various stages of loading. The proposed theory predicts with good correlations the experimental deflections and moments of any loading stages of the columns. The theory has been used to obtain the required variables, to arrive at the initial predicted design loads of the investigated columns. Good correlations of the moments derived from observed strains have also been obtained. The developed theory predicts satisfactorily the buckling collapse loads of the columns. Although the theory has been derived for axially I loaded very slender reinforced concrete-columns, it seems to accept satisfactorily eccentricities of up to about 10 mm. This was confirmed after extensive comparisons of the theoretical buckling collapse loads with the applicable tests of other authors. Creep In the columns investigated was discovered to be one of the major factors for serious consideration. This was conclusively revealed from the observations on the last two very long term creep tests on columns. The actual safe sustained loads for these very slender columns of slenderness ratios, L/H, between 40 and 79 seem to be between 33% and 19% of the short term buckling collapse loads. The reduced modulus approach to predict the safe long term sustained loads seems to give reasonable values for L/H ratios of 40 and 50. The recommendations given for the proposed design of very slender reinforced concrete columns seem to be adequate and simple to use in practice. They are further simplified by the derivation of two equations for the reduction factors, R, for the slenderness ratios between 36 and 40 and between 40 and 79 respectively. The investigation has proved that very slender reinforced concrete columns are very dangerous structural members, as they tend to have violent buckling failures. Nevertheless, It must be prudent not to design against disaster at any cost. This Investigation seemed to have enhanced considerably knowledge of the design of very slender reinforced concrete columns.

Slender structures are elegant aesthetically. The insufficiency in knowledge of the real resistance to buckling of very slender reinforced concrete columns leads to an exaggeration of the sizes of the columns. _The examples of concrete compression members cited and constructed in Industry on a global basis suggest that very slender columns have inherent safety both from the point of view of the ultimate strength and stability. The strengths of columns given. by the British codes would seem to be exceeded by many of the long slender reinforced concrete columns and struts which have been used Internationally. Both the theoretical and the experimental short term investigations have been carried out to establish the behaviour of hinged, very slender reinforced concrete columns at various stages'of axial loading. Forty three very slender reinforced concrete columns of two different square cross sections with two sizes of longitudinal reinforcements with lateral ties were cast. Slenderness rates, L A, were varied from 30 to 79. Special factors were obtained to relate the actual modulus of elasticity of concrete in columns at buckling failure to a knowledge of the initial modulus of elasticity of concrete in control cylinder specimens. Both theoretical and experimental graphs of load against moment, made dimensionless for critical sections of columns have been obtained. Dimensionless load-moment interaction diagrams using material failure as the criterion have been superimposed on these graphs to show considerable inherent material strength of the tested columns near buckling collapse failures. A theory using the fundamental approach has, been developed to predict the deflected shape and moments along the, heights of the columns at various stages of loading. The proposed theory predicts with good correlations the experimental deflections and moments of any loading stages of the columns. The theory has been used to obtain the required variables, to arrive at the initial predicted design loads of the investigated columns. Good correlations of the moments derived from observed strains have also been obtained. The developed theory predicts satisfactorily the buckling collapse loads of the columns. Although the theory has been derived for axially I loaded very slender reinforced concrete-columns, it seems to accept satisfactorily eccentricities of up to about 10 mm. This was confirmed after extensive comparisons of the theoretical buckling collapse loads with the applicable tests of other authors. Creep In the columns investigated was discovered to be one of the major factors for serious consideration. This was conclusively revealed from the observations on the last two very long term creep tests on columns. The actual safe sustained loads for these very slender columns of slenderness ratios, L/H, between 40 and 79 seem to be between 33% and 19% of the short term buckling collapse loads. The reduced modulus approach to predict the safe long term sustained loads seems to give reasonable values for L/H ratios of 40 and 50. The recommendations given for the proposed design of very slender reinforced concrete columns seem to be adequate and simple to use in practice. They are further simplified by the derivation of two equations for the reduction factors, R, for the slenderness ratios between 36 and 40 and between 40 and 79 respectively. The investigation has proved that very slender reinforced concrete columns are very dangerous structural members, as they tend to have violent buckling failures. Nevertheless, It must be prudent not to design against disaster at any cost. This Investigation seemed to have enhanced considerably knowledge of the design of very slender reinforced concrete columns. / Scientific Research Council

Thin-walled cold-formed steel (CFS) has exhibited inherent structural and architectural advantages over other constructional materials, for example, high strength-to-weight ratio, ease of fabrication, economy in transportation and the flexibility of sectional profiles, which make CFS ideal for modern residential and industrial buildings. They have been increasingly used as purlins as the intermediate members in a roof system, or load-bearing components in low- and mid-rise buildings. However, using CFS members in building structures has been facing challenges due to the lack of knowledge to the fire performance of CFS at elevated temperatures and the lack of fire design guidelines. Among all available design specifications of CFS, EN1993-1-2 is the only one which provided design guidelines for CFS at elevated temperatures, which, however, is based on the same theory and material properties of hot-rolled steel. Since the material properties of CFS are found to be considerably different from those of hot-rolled steel, the applicability of hot-rolled steel design guidelines into CFS needs to be verified. Besides, the effect of non-uniform temperature distribution on the failure of CFS members is not properly addressed in literature and has not been specified in the existing design guidelines. Therefore, a better understanding of fire performance of CFS members is of great significance to further explore the potential application of CFS. Since CFS members are always with thin thickness (normally from 0.9 to 8 mm), open cross-section, and great flexural rigidity about one axis at the expense of low flexural rigidity about a perpendicular axis, the members are usually susceptible to various buckling modes which often govern the ultimate failure of CFS members. When CFS members are exposed to a fire, not only the reduced mechanical properties will influence the buckling capacity of CFS members, but also the thermal strains which can lead additional stresses in loaded members. The buckling behaviour of the member can be analysed based on uniformly reduced material properties when the member is unprotected or uniformly protected surrounded by a fire that the temperature distribution within the member is uniform. However if the temperature distribution in a member is not uniform, which usually happens in walls and/or roof panels when CFS members are protected by plaster boards and exposed to fire on one side, the analysis of the member becomes very complicated since the mechanical properties such as Young’s modulus and yield strength and thermal strains vary within the member. This project has the aim of providing better understanding of the buckling performance of CFS channel members under non-uniform temperatures. The primary objective is to investigate the fire performance of plasterboard protected CFS members exposed to fire on one side, in the aspects of pre-buckling stress distribution, elastic buckling behaviour and nonlinear failure models. Heat transfer analyses of one-side protected CFS members have been conducted firstly to investigate the temperature distributions within the cross-section, which have been applied to the analytical study for the prediction of flexural buckling loads of CFS columns at elevated temperatures. A simplified numerical method based on the second order elastic – plastic analysis has also been proposed for the calculation of the flexural buckling load of CFS columns under non-uniform temperature distributions. The effects of temperature distributions and stress-strain relationships on the flexure buckling of CFS columns are discussed. Afterwards a modified finite strip method combined with the classical Fourier series solutions have been presented to investigate the elastic buckling behaviour of CFS members at elevated temperatures, in which the effects of temperatures on both strain and mechanical properties have been considered. The variations of the elastic buckling loads/moments, buckling modes and slenderness of CFS columns/beams with increasing temperatures have been examined. The finite element method is also used to carry out the failure analysis of one-side protected beams at elevated temperatures. The effects of geometric imperfection, stress-strain relationships and temperature distributions on the ultimate moment capacities of CFS beams under uniform and non-uniform temperature distributions are examined. At the end the direct strength method based design methods have been discussed and corresponding recommendations for the designing of CFS beams at elevated temperatures are presented. This thesis has contributed to improve the knowledge of the buckling and failure behaviour of CFS members at elevated temperatures, and the essential data provided in the numerical studies has laid the foundation for further design-oriented studies.