<p>Today’s microprocessors with millions of transistors perform high-complexity computing at multi-gigahertz clock frequencies. The ever-increasing chip size and speed call for new methodologies in clock distribution network. Conventional global synchronization techniques exhibit many drawbacks in the advanced VLSI chips such as high-speed microprocessors. A significant percentage of the total power consumption in a microprocessor is dissipated in the clock distribution network. Also since the chip dimensions increase, clock skew management becomes very challenging in the framework of conventional methodology. Long interconnect delays limit the maximum clock frequency and become a bottleneck for future microprocessor design. In such a situation, new alternative techniques for synchronization in system-on-chip are demanded.</p><p>This thesis presents new alternatives for traditional clocking and synchronization methods, in which, speed and power consumption bottlenecks are treated. For this purpose, two new techniques based on mesochronous synchronization and resonant clocking are investigated. The mesochronous synchronization technique deals with remedies for skew and delay management. Using this technique, clock frequency up to 5 GHz for on-chip communication is achievable in 0.18-<em>μ</em>m CMOS process. On the other hand the resonant clocking solves significant power dissipation problem in the clock network. This method shows a great potential in power saving in very large-scale integrated circuits. According to measurements, 2.3X power saving in clock distribution network is achieved in 130-nm CMOS process. In the resonant clocking, oscillator plays a crucial role as a clock generator. Therefore an investigation about oscillators and possible techniques for jitter and phase noise reduction in clock generators has been done in this research framework. For this purpose a study of injection locking phenomenon in ring oscillators is presented. This phenomenon can be used as a jitter suppression mechanism in the oscillators. Also a new implementation of the DLL-based clock generators using ring oscillators is presented in 130-nm CMOS process. The measurements show that this structure operates in the frequency range of 100 MHz-1.5 GHz, and consumes less power and area compared to the previously reported structures. Finally a new implementation of a 1.8-GHz quadrature oscillator with wide tuning range is presented. The quadrature oscillators potentially can be used as future clock generators where multi-phase clock is needed.</p> / Report code: LiU-TEK-LIC-2006:22

Today’s microprocessors with millions of transistors perform high-complexity computing at multi-gigahertz clock frequencies. The ever-increasing chip size and speed call for new methodologies in clock distribution network. Conventional global synchronization techniques exhibit many drawbacks in the advanced VLSI chips such as high-speed microprocessors. A significant percentage of the total power consumption in a microprocessor is dissipated in the clock distribution network. Also since the chip dimensions increase, clock skew management becomes very challenging in the framework of conventional methodology. Long interconnect delays limit the maximum clock frequency and become a bottleneck for future microprocessor design. In such a situation, new alternative techniques for synchronization in system-on-chip are demanded. This thesis presents new alternatives for traditional clocking and synchronization methods, in which, speed and power consumption bottlenecks are treated. For this purpose, two new techniques based on mesochronous synchronization and resonant clocking are investigated. The mesochronous synchronization technique deals with remedies for skew and delay management. Using this technique, clock frequency up to 5 GHz for on-chip communication is achievable in 0.18-μm CMOS process. On the other hand the resonant clocking solves significant power dissipation problem in the clock network. This method shows a great potential in power saving in very large-scale integrated circuits. According to measurements, 2.3X power saving in clock distribution network is achieved in 130-nm CMOS process. In the resonant clocking, oscillator plays a crucial role as a clock generator. Therefore an investigation about oscillators and possible techniques for jitter and phase noise reduction in clock generators has been done in this research framework. For this purpose a study of injection locking phenomenon in ring oscillators is presented. This phenomenon can be used as a jitter suppression mechanism in the oscillators. Also a new implementation of the DLL-based clock generators using ring oscillators is presented in 130-nm CMOS process. The measurements show that this structure operates in the frequency range of 100 MHz-1.5 GHz, and consumes less power and area compared to the previously reported structures. Finally a new implementation of a 1.8-GHz quadrature oscillator with wide tuning range is presented. The quadrature oscillators potentially can be used as future clock generators where multi-phase clock is needed. / Report code: LiU-TEK-LIC-2006:22

Low size, low power, and wearable bio-signal recording systems require acquisition front-ends with high common-mode rejection for interference suppression and adjustable gain to provide an optimum signal level to a cascading analog-to-digital stage. This thesis presents the realization of microcontroller operated double-differential (DD) recording setup with automatic gain control (AGC) and automatic balance control, which can adjust the magnitude of recorded bio-potential signal to a target level and reject common-mode interference for full-bandwidth recording without filtering. Microcontroller code realizes the automatic control method of gain and balance adjustment by detecting, computing, and varying parameters to set timing clock pulses, which determine the gain magnitude and balance state. The automatic balance control compensates for imbalance in electrode interface impedance. The double-differential amplifier is implemented using two integrated variable gain amplifiers (ASIC) and one adder. Measured results of the variable gain amplifiers fabricated in 0.35 £gm CMOS technology show an input spot noise of 169 nV/¡ÔHz, a NEF below 10, and a circuit active area of 0.017 mm2 with a power consumption of 1.44 £gW. Measured results of the double-differential amplifier setup confirm interference suppression of 25.7 dB, tunable gain range of 39.6 dB, and 239 nV/¡ÔHz noise assuming ¡Ó10% interface mismatch. Practical measured examples incorporating the chips confirm gain control suitable for bio-potential recording and interference suppression in a balanced DD arrangement for electrocardiogram and electromyogram recording.

This work presents novel continuous-time delta-sigma modulator architectures with low-power consumption and improved signal transfer functions which are suitable for wideband A/D conversion in wireless applications, e.g., 3G and 4G receivers. The research has explored two routes for improving the overall performance of continuous-time delta-sigma modulator. The first part of this work proposes the use of the power efficient Successive-Approximations (SAR) architecture, instead of the conventional Flash ADC, as the internal quantizer of the delta-sigma modulator. The SAR intrinsic latency has been addressed by means of a faster clock for the quantizer as well as full-period delay compensation. The use of SAR quantizer allows for increasing the resolution while reducing the total power consumption and complexity. A higher resolution quantizer, made feasible by the SAR, would allow implementing more aggressive noise shaping to facilitate wideband delta-sigma A/D conversion at lower over-sampling-rates. As proof of concept, a first-order CT delta-sigma modulator with a 5-bit SAR quantizer is designed and implemented in a 130 nm CMOS process which achieves 62 dB dynamic range over 1.92 MHz signal bandwidth meeting the requirements of the WCDMA standard. The prototype modulator draws 3.1 mW from a single 1.2 V supply and occupies 0.36 mm2 of die area. The second part of this research addresses the issue of out-of-band peaking in the signal-transfer-function (STF) of the widely used feedforward structure. The STF peaking is harmful to the performance of the modulator as it allows an interferer to saturate the quantizer and result in severe harmonic distortion and instability. As a remedy to this problem a general low-pass and peaking-free STF design methodology has been proposed which allows for implementing an all-pole filter in the input signal path for any given NTF. Based on the proposed method, the STF peaking of any feedforward modulator can be eliminated using extra feed-in paths to all the integrator inputs. A major drawback of the conventional feedforward topology having low-pass STF is the large sensitivity of the STF to the coefficients. In particular, component mismatch, due to random errors in the relative values of individual resistors or capacitors, can significantly degrade the anti-aliasing of the CT modulator and give rise to the unwanted STF peaking. To solve this problem two new architectures, namely dual-feedback and dual-feed-in are proposed which allow us to synthesize a low-pass STF with a smaller number of coefficients than the feedforward structure. The dual-feedback structure which shows significantly lower sensitivity to coefficient mismatch is extensively analyzed and simulated. Also for proof of concept a third-order modulator is implemented in a 130 nm CMOS process which achieves 76 dB dynamic-range over 5 MHz signal bandwidth meeting, for example, the requirements of a DVB-H receiver standard. In addition the modulator shows 77 dB anti-aliasing and less than 0.1 dB worst-case STF peaking. The measured power consumption of the modulator is 6 mW from a single 1.2 V and the die area is 0.56 mm2.

This paper discusses the challenges and the trade-offs in the design of laser drivers for very-short distance optical communications. A prototype integrated circuit is designed and fabricated in 28 nm super-low-power CMOS technology. The power consumption of the transmitter is 17.2 mW excluding the VCSEL that in our test has a DC power consumption of 10 mW. The active area of the driver is only 0.0045 mm². The driver can achieve an error-free (<BER < 10^12) electrical data-rate of 25 Gbit/s using a pseudo random bit sequence of 2^7-1. When the driver is connected to the VCSEL module an open optical eye is reported at 15 Gbit/s. In the tested bias point the VCSEL module has a measured bandwidth of 10.7 GHz.