No description available.

M.Ing. / The instability of partially stiffened stainless steel compression members due to local buckling of the flange element or flange and lip interaction has not been studied before. In this investigation the critical local buckling and post-buckling behavior of cold-formed partially stiffened stainless steel compression elements are studied in order to determine the applicability of the current design specification ...

D.Ing. (Civil Engineering) / Please refer to full text to view abstract

No description available.

M.S.

published_or_final_version / abstract / Civil Engineering / Doctoral / Doctor of Philosophy

The structural behaviour of single shear bolted connections and double shear bolted connections of cold-formed stainless steel at elevated temperatures and post-fire condition has been investigated in this study. The current design rules on bolted connections of cold-formed stainless steel are mainly based on those of carbon steel, and are applicable for room (ambient) temperature condition only. These design rules may not be applicable for elevated temperatures. Therefore, design guidelines should be prepared for bolted connections of cold-formed stainless steel structures at elevated temperatures. The key findings of the investigation are described in the following paragraphs. A total of 25 tensile coupon tests were conducted to investigate the material deterioration of three different grades of stainless steel at elevated temperatures. The stainless steels are austenitic stainless steel EN 1.4301 (AISI 304) and EN 1.4571 (AISI 316Ti having small amount of titanium) as well as lean duplex stainless steel EN 1.4162 (AISI S32101). Totally 434 tests on bolted connections of stainless steel were performed in the temperature ranged from 22 to 950 ºC using both steady state and transient state test methods. The test results were compared with the nominal strengths calculated from the American Specification, Australian/New Zealand Standard and European codes for stainless steel structures. In calculating the nominal strengths of the connections, the material properties at elevated temperatures were used in the design equations for room temperature. It is shown that the nominal strengths predicted by these specifications are generally conservative at elevated temperatures. A total of 78 cold-formed stainless steel single shear and double shear bolted connections were tested in post-fire condition. The test results were compared with those tested at room temperature. Generally, it is found that the bolted connection strengths in post-fire condition cooling down from 350 and 650 ºC are higher than those tested at room temperature for all three grades of stainless steel. Finite element models for single shear and double shear bolted connections were developed and verified against the experimental results. Static analysis technique was used in the numerical analyses. Extensive parametric studies that included 450 specimens were performed using the verified finite element models to evaluate the bearing resistances of bolted connections of stainless steel at elevated temperatures. Design equations for bearing resistances of cold-formed stainless steel single shear and double shear bolted connections were proposed based on both the experimental and numerical results in the temperature ranged from 22 to 950 ºC. The bearing resistances of bolted connections obtained from the tests and the finite element analyses were compared with the nominal strengths calculated using the current design rules and also compared with the predicted strengths calculated using the proposed design equations. It is shown that the proposed design equations are generally more accurate and reliable in predicting the bearing resistances of bolted connections at elevated temperatures than the current design rules. The reliability of the current and proposed design rules was evaluated using reliability analysis. The proposed design equations are recommended for bolted connections assembled using cold-formed stainless steels. / published_or_final_version / Civil Engineering / Doctoral / Doctor of Philosophy

Made available in DSpace on 2014-10-09T12:38:44Z (GMT). No. of bitstreams: 0 / Made available in DSpace on 2014-10-09T14:05:20Z (GMT). No. of bitstreams: 1 06007.pdf: 6761154 bytes, checksum: 544e5e82c9fa4e346e3dac046b8ce34f (MD5) / Tese (Doutoramento) / IPEN/T / Instituto de Pesquisas Energeticas e Nucleares - IPEN/CNEN-SP

Made available in DSpace on 2014-10-09T12:38:44Z (GMT). No. of bitstreams: 0 / Made available in DSpace on 2014-10-09T14:05:20Z (GMT). No. of bitstreams: 1 06007.pdf: 6761154 bytes, checksum: 544e5e82c9fa4e346e3dac046b8ce34f (MD5) / Tese (Doutoramento) / IPEN/T / Instituto de Pesquisas Energeticas e Nucleares - IPEN/CNEN-SP

M.Ing. / Because cold-formed stainless steel is a new type of light steel material and dose not have a long history of utilisation in structures, there are many issues that need to be researched and discussed. Making a more thorough investigation and study of cold-formed stainless steels is essential. As a numerical analysis tool, the finite element method proves to be useful in structural analysis. The buckling modes of cold-formed stainless steel members, such as local, flexural, torsional and torsional-flexural buckling, are well known and well documented in design specifications. Distortional buckling is a special kind of buckling mode, which is less well known. Researchers have recently paid more attention to this problem. For stainless steel structures, it is necessary to investigate their behaviour when distortional buckling occurs. In this project, the distortional buckling of cold-formed stainless steel columns under axial compression is investigated. The finite element method is used to analyse and calculate different buckling modes, especially distortional buckling. This is compared to experimental results and other theoretical predictions. The ABAQUS finite element code is used throughout. Finite element modelling is very important prior to processing and analysis. ABAQUS models are created to study distortional buckling. The initial imperfection of structural members is taken into account with these models, using specific sine wave descriptions with respect to different structural parameters. A dynamic processing approach is chosen in the finite element analysis. The effectiveness and accuracy of these models have been verified by both experimental tests and theoretical calculations. Buckling mode and behaviour are predicted and analysed in terms of the finite element models and processes. Suggestions are made for buckling analysis and design based on the research results.