Thesis (M.Phil.)--Hong Kong University of Science and Technology, 2006. / Includes bibliographical references. Also available in electronic version.

This thesis combines four manuscripts of which I am the first author. The first manuscript examines the phase separation process and related process parameters. This article provides detailed experimental results of the delivery and separation process. During the delivery of 40% Liquid-to-Powder-Ratio (LPR) paste, only 62[plus ou moins]3 % of the paste initially present in the 10-mL syringe could be injected. Thereafter, the remaining paste in the syringe was not amendable to injection suggesting the existence of liquid separation. The LPR of the extruded fraction of a 37% LPR paste ranged from 40.9[plus ou moins]2.0 % to 42.7[plus ou moins]2.1 %. On the other hand, a shortage of water content was measured for the paste left in the syringe. Furthermore, this shortage was gradual, ranging from 27.3[plus ou moins]1.9 % at the plunger side to 30.9[plus ou moins]1.6 % at the tip side. In addition, this article presents rheological measurements of the paste showing clearly that the limitation was not related to the viscosity of the paste but rather to the phase separation process. Specifically, the yield stresses were around 66[plus ou moins]2 Pa, 19[plus ou moins]2 Pa, and 8[plus ou moins]0 Pa for 40%, 50%, and 65% LPR suspensions, respectively. For the three studied LPRs, the viscosity rapidly dropped with an increase of shear rate to a level below 10 Pas. The second manuscript examines the possibility that fine particles migrate faster than large particles during injection, hence leading to a so-called size separation. This size separation process can be expected from the scientific literature, but had not been investigated prior to my study. In a way, the size separation is very similar to the phase separation process. An electrohydraulic system was used to control the delivery process. The result of this second study, showed no evidence of size separation. It was therefore concluded that the main mechanism underlying the limited injectability is the liquid phase filtration through the porous particles bed of the paste. The third manuscript examines the role of powder porosity ([epsilon]) and permeability. For that purpose, an electronically assisted device was used to measure the powder permeability. In this study, three powders were examined for comparison and better understanding. In addition, the powder permeability was correlated with the paste injectability. Adding 3 wt% of a fine nanosized powder to the [bêta]-TCP powder decreased the mixture permeability at a porosity of [varepsilon] = 67.5% from 6.4.10[exposant]-13 m[exposant]2 to 5.6.10[exposant]-13 m[exposant]2 and increased the injected volume fraction from 70.8[plus ou moins]1.9 % to 84.5[plus ou moins]0.9 %. The results showed clear evidence that the injectability can be improved by admixing different powders. However, permeability was not a strong predictor of the liquid separation phenomenon. The last manuscript provides a practical solution to reduce phase separation occurrence. For that purpose an ultrasonication process was suggested and applied during the delivery process to improve injectability. Specifically, sonicating the paste reduced agglomeration, decreased paste viscosity due to the shear thinning and therefore reduced phase separation. The result of the ultrasound assisted delivery was remarkably effective since it has been able to fully deliver highly concentrated paste, with minimal force exerted by hand. For instance, the injectable volume fraction of a 40% LPR paste injected with a 5-mL syringe increased significantly from 71.3[plus ou moins]0.5 % to 99.1[plus ou moins]0.9 % using 150 microns ultrasonic amplitude at a 20 kHz frequency. This chapter provides clear evidence that an electromechanical approach can be used to improve the injectability of a calcium phosphate paste. This thesis addresses an important limitation of calcium phosphate cements, namely phase separation during injection. This thesis also provides a scientific understanding and a practical solution for this problem. The electromechanical solution proposed here is one out of several possible solutions. Future work may focus on building numerical tools to help in the design of the powder and to understand the link between powder properties, rheology, syringe geometry and phase separation."--Résumé abrégé par UMI

published_or_final_version / abstract / Orthopaedics and Traumatology / Doctoral / Doctor of Philosophy

published_or_final_version / Dentistry / Master / Master of Dental Surgery

published_or_final_version / abstract / toc / Dentistry / Doctoral / Doctor of Philosophy

No description available.

Orthopaedic reconstruction often involves the surgical introduction of structural implants that provide for rigid fixation, skeletal stabilization, and bone integration. The high stresses incurred by these implanted devices have historically limited material choices to metallic and select polymeric formulations. While mechanical requirements are achieved, these non-degradable materials do not participate actively in the remodeling of the skeleton and present the possibility of long-term failure or rejection. This is particularly relevant in cervical fusion, an orthopaedic procedure to treat damaged, degenerative or diseased intervertebral discs. A significant improvement on the available synthetic bone replacement/regeneration options for implants to treat these conditions in the cervical spine may be achieved with the development of primarily mineral biocomposites comprised of a bioactive ceramic matrix reinforced with a biodegradable polymer. Such a biocomposite may be engineered to possess the clinically required mechanical properties of a particular application, while maintaining the ability to be remodeled completely by the body. A biocomposite of Si-doped calcium phosphate (Si-CaP) and poly(ε-caprolactone) (PCL) was developed for application as such a synthetic bone material for potential use as a fusion device in the cervical spine. In this thesis, a method by which high mineral content Si-CaP/PCL biocomposites with interpenetrating matrices of mineral and polymer phases may be prepared will be demonstrated, in addition to the effects of the various preparation parameters on the biocomposite density, porosity and mechanical properties. This new technique by which dense, primarily ceramic Si-CaP/PCL biocomposites were prepared, allowed for the incorporation of mineral contents ranging between 45-97vol%. Polymer infiltration, accomplished solely by passive capillary uptake over several days, was found to be capable of fully infiltrating the microporosity of the sintered calcium phosphate ceramic. After infiltration, these biocomposite materials demonstrated an increase in compressive strength, flexural strength and Young’s modulus with increasing ceramic content and met design targets for use as a cervical fusion prosthesis. The biocomposite was amenable to shaping and drilling and was found to maintain its strength after 30 days immersion in Earle’s Balanced Salt. / Thesis (Ph.D, Mechanical and Materials Engineering) -- Queen's University, 2009-11-24 16:18:16.461

Thesis (Master)--İzmir Institute of Technology, İzmir, 2004 / Includes bibliographical references (leaves. 94).

Thesis (Ph. D.)--Drexel University, 2005. / Includes abstract and vita. Includes bibliographical references (leaves 216-221).

Thesis (Ph. D.)--University of Wisconsin--Madison, 1934. / Typescript. eContent provider-neutral record in process. Description based on print version record. Includes bibliographical references.