Cellular beams (CBs) have become increasingly popular in the UK and other countries over the recent years. However, the research into the behaviour of these beams has not advanced at the same rate. There is still no robust codified guidance available to design cellular beams and cellular composite beams at ambient and elevated temperatures. Meanwhile, numerical simulation approaches, such as Finite Element (FE) analysis, have enabled the researchers to advance their investigations into various behavioural aspects of these beams. In this research, the developed numerical models using the ABAQUS package were able to predict, to a high accuracy, the failure mode and failure load (temperature) of CBs and cellular composite beams at ambient and elevated temperatures.Within the investigations on cellular beams, it was found that predicting the correct failure mode by FE models can be extremely sensitive to the maximum load increment allowed in the software (for elastic-perfectly plastic stress-strain relationship for steel material) and also to the applied boundary conditions. In particular, slight changes in the boundary conditions applied to the top flange of the beam, can change the failure mode from web post buckling to Vierendeel mechanism. The buckling resistance of the web post of cellular composite beams was found to be sensitive to the amplitude of web imperfections at ambient temperature. However, the ultimate resistance of these beams was not affected by the amplitude of web imperfections at elevated temperature. This suggests that the 'Strut' model used in current design method to estimate the buckling resistance of the web post is not reasonable at elevated temperature and needs to be modified. The failure of cellular composite beams under a uniform distributed load (UDL) and at elevated temperatures, was governed by distorsional buckling before the development of web post buckling. Adding full-height web stiffeners to the beam in such cases improved their loading resistance at ambient temperature by up to 15% and prevented the occurrence of distorsional buckling at elevated temperature. Increasing the end-restraints decreased the deflections of CBs which are governed by catenary action at elevated temperature. However, this also critically promoted the occurrence of web post buckling which could be due to the P-∆ effects and instabilities resulting from the restrained expansion of the beam.Asymmetric beams showed a higher sensitivity and vulnerability to the magnitude of the load ratio than symmetric sections. This suggests a more prudent approach for the fire design of asymmetric beams as opposed to symmetric beams.

no / Cellular beams are the preferred form of long span construction in multi-storey buildings. For efficient design of composite cellular beams, asymmetric sections are often manufactured in which the bottom flange is larger than the top flange. A further innovation is in the use of 80mm deep deck profiles which allows beam spacing to be increased to 4.5m, and so the effective slab width acting compositely with the long span beams is also increased. The values for shear connector (stud) resistance given in Eurocode 4 (EN 1994-1-1), when used in combination with these modern decking profiles, have led to problems in achieving the minimum degree of shear connection for composite beams in comparison to the former BS 5950-3. For secondary beams, the number of shear connectors that can be accommodated in a span is limited by the spacing of the deck ribs (typically 300mm for deep trapezoidal profiles), and it is found that even for pairs of shear connectors per deck rib, it is impossible to satisfy the shear connection rules in Eurocode 4 for long span asymmetric beams. SCI, with support from the Research Fund for Coal and Steel, is on the way to resolving this problem in design to Eurocode 4, and has completed a test on a 15.3m composite cellular beam at the University of Bradford. This is believed to be the longest composite cellular beam test ever carried out. The test was part-sponsored by ASD Westok.

Yes / Steel concrete composite beams have been increasingly used in practice due to their advantages with respect to their structural features and constructability. However, in conventional composite beam systems composite action is applied via shear connectors welded at the top flange of the down-stand steel beam and embedded in the concrete slabs, making it less favourable for the beam system to be disassembled and reused. This paper presents a numerical study of a new composite beam system consisting of a cellular steel beam, metal deck flooring and demountable shear connectors. According to the experimental study, this composite beam system made the demounting, reassembly, and member reuse possible, and did not compromise the loading capacity. In the numerical study presented in the paper, a finite element model was developed and validated against the results obtained from the previous experimental study. The parametric study further examined the effects of concrete strength, shear connector arrangements and asymmetry ratios of steel beam section to the load capacity of the composite beam system. The analysis and comparison provided a deeper insight into the behaviour of this type of shear connector. Through this numerical study, the structural merits of the composite beam system using demountable shear connectors were highlighted. Finally, the mid-span plastic moment of the composite beam was predicted using the direction method provided in SCI publications and compared with the moment–deflection relationship obtained from FE modelling. / The research leading to these results is part of a joint project of the University of Bradford, the University of Luxemburg, the Technology University of Delft, the Steel Construction Institute, Tata Steel, Lindab S. A., BmS and AEC3 Ltd. The authors gratefully acknowledge the funding received from the European Commission: Research Fund for Coal and Steel (RFCS-2015, RPJ, 710040). In addition, deep appreciation to Mr. Stephen Robinson for his work done in the laboratory.

En situation d’incendie, la dégradation des propriétés mécaniques des matériaux constitutifs d’une structure peut sensiblement en modifier le comportement global. Ainsi, lors d’essais au feu ou de sinistres réels, des flèches significatives sont observées sans ruine globale du plancher. Ceci traduit l’activation d’un mécanisme basé sur une borne supérieure de plasticité en grands déplacements et appelé effet membrane. Ainsi, malgré la perte des propriétés du béton, de l’acier d’armatures et de l’acier de construction des poutres connectées à une dalle en béton armé ou mixte acier-béton, la capacité portante de cette dalle se définit comme une fonction croissante de sa flèche. En pratique, le comportement complexe des planchers mixtes acier-béton peut être appréhendé par des modèles dits simplifiés ou avancés, suivant le niveau de précision souhaité. La méthode analytique FRACOF permet par exemple d’étudier un plancher global à température élevée, en se basant sur les modèles de comportement simplifiés des matériaux, acier et béton, définis dans les Eurocodes. Par cette méthode, la capacité portante d’une dalle peut alors être déterminée en tenant compte des profilés métalliques connectés à la dalle, et de l’activation d’un effet membrane en grands déplacements. Cette méthode analytique a été validée par une comparaison à des modèles éléments finis, ainsi qu’à des résultats d’essais au feu en grandeur nature. Elle est applicable à des profilés en acier laminé à chaud avec des portées pouvant atteindre 20 m. Or le franchissement de ces portées nécessite des sections de poutre à forte inertie, afin de limiter les flèches du plancher en service. Pour limiter la quantité d’acier que requerraient de telles poutres, le recours à des poutres cellulaires est une solution pratique et esthétique. Un modèle élément finis de poutres cellulaires en acier seul et mixtes est proposé dans le cadre de la thèse de doctorat. Le comportement thermo-mécanique des poutres cellulaires en acier seul est modélisé sous le code Cast3M. Les poutres mixtes sont modélisées en combinant un calcul de transfert thermique sous Cast3M et une analyse mécanique sous ANSYS. Les poutres en acier et la dalle en béton ou mixte sont représentées par des éléments de type coque. Les connecteurs sont représentés par des éléments de type poutre. Ce modèle tridimensionnel tient par ailleurs compte des non-linéarités matérielle et géométrique. Il est confronté à des résultats d’essais à températures normale et élevée. La validation du modèle est suivie d’une comparaison à une méthode analytique existante pour en vérifier la précision et le degré de conservatisme. Les poutres cellulaires sont ensuite étudiées en tant que partie intégrante de planchers mixtes acier-béton sous incendie. Un essai en grandeur nature sous feu réel met en évidence l’activation d’un effet membrane en présence de poutres cellulaires non-protégées, sans ruine du plancher. Les résultats de l’essai sont utilisés pour calibrer un modèle élément fini tridimensionnel. La calibration est effectuée en s’appuyant sur la distribution des températures dans les différents composants du plancher, la durée de résistance au feu, la forme des déformées et les modes de ruine. Ensuite, le modèle, qui peut reproduire le comportement thermo-mécanique d’un plancher mixte, est utilisé pour évaluer une proposition d’extension de la méthode FRACOF à des planchers mixtes comportant des poutres cellulaires. / In a fire situation, the decrease of the material properties of a structure can significantly modify its overall behaviour. Hence, during fire tests or real fires, very large deflections can be observed on a floor without any global collapse. This highlights the activation of a large-displacement plastic upper bound mechanism called membrane action. Thus, in spite of the property loss of concrete, reinforcement steel and constructional steel of the beams connected to a reinforced concrete or composite slab, the load bearing capacity of this slab is defined as an increasing function of its vertical deflection. In practice, the behaviour of composite steel and concrete floors can be assessed with simplified or advanced models, depending on the expected level of precision. For instance, the analytical method named FRACOF enables to study a whole floor at elevated temperatures, on the basis of the Eurocodes simplified models for the behaviour of steel and concrete. With this method, the load bearing capacity of a slab can then be estimated taking account of steel profiles connected to the slab and tensile membrane action in large displacements. This analytical method has been validated against finite elements models as well as results from full scale fire tests. It applies to hot-rolled steel profiles spanning up to 20 m. However, such spans require sections with a great moment of area to limit the floor deflection in serviceability state. In order to limit the amount of steel required, cellular beams can be utilized as a practical and aesthetical solution. A finite element model for steel and composite steel and concrete cellular beams is proposed in the scope of the PhD thesis. The thermo-mechanical behaviour of steel cellular beams is modelled under Cast3M code. Composite beams are modelled combining a heat transfer calculation under Cast3M to a mechanical analysis under ANSYS. The steel beams and the reinforced or composite slab are modelled with shell elements. The shear studs are modelled with beam elements. Besides, this 3D model takes into account both material and geometrical nonlinearities. It is compared with tests results at both normal and elevated temperatures. Once validated, the model is compared to an existing analytical method in order to check the precision and the level of conservatism of the latter. Then, cellular beams are studied as part of composite steel and concrete floors in a fire situation. A full-scale natural fire test puts into evidence tensile membrane action with unprotected cellular beams, without any overall collapse. The test results are used for calibrating a 3D finite element model. This calibration relies on the temperature distribution in the different parts of the floor components, the fire resistance degree, the deformed shape and the failure modes. The model, which can reproduce the thermo-mechanical behaviour of a composite floor, is then utilized for assessing an extension proposal of the FRACOF method to composite floors made of cellular beams.