No description available.

No description available.

Discharging cheese production wastewater with high concentrations of organics and nutrients is detrimental to receiving aquatic systems, as the release of these deleterious substances cause oxygen depletion, and eutrophication respectively. On-site treatment of cheese production wastewater requires the removal of high concentrations of organics and nutrients with a small land footprint to meet regulations. There is therefore a critical need for compact, high-rate, cost-effective wastewater technologies such a as the moving bed biofilm reactor (MBBR). Although MBBR systems have been well established for carbon and nitrogen removal, to date only a limited number of studies have achieved enhanced biological phosphorous removal in sequencing batch moving bed biofilm reactor (SB-MBBR) systems, and only for municipal-strength wastewater. Operating SB-MBBR systems under sequencing batch mode enables the reactor operation to be well synced to the fluctuating influent concentrations and flow characteristics of cheese production wastewaters. Furthermore, cycling between anaerobic and aerobic conditions can be achieved in a single sequencing batch reactor, which can promote the proliferation of poly-phosphate accumulating organisms. The SB-MBBR is studied in this research for the removal of carbon, nitrogen, and phosphorous from cheese production wastewaters. Specifically, the effects of anaerobic staging time, aeration rate, enhanced aerobic operation, and adding a second reactor in series was studied by analyzing the kinetics, biofilm characteristics, and microbiome. Extending the anaerobic staging time was shown to achieve aerobic soluble chemical oxygen demand removal rates of 92.5±2.8 g·m⁻²d⁻¹, by selecting for a thinner biofilm with, with a lower biofilm dry-density and a more rough biofilm surface, and therefore likely a biofilm with an enhanced mass transport. A significant shift in the microbiome was observed with longer anaerobic staging times and lower aeration, whereby possible putative poly-phosphate accumulating organisms including Brachymonas, and Dechloromonas were selected for in greater relative abundances compared to anaerobic bacteria. The total phosphorous removal in the possibly resulted from enhanced biological phosphorous removal, supported by the high abundance of putative poly-phosphate accumulating organisms (43.1±8.4%), which dominated the biofilms in the SB-MBBRs with 120 and 168 minute anaerobic staging times. Finally, total ammonia nitrogen oxidation was achieved through partial nitritation with a two reactor in series configuration with a removal rate of 1.07±0.05 g-N·m⁻²d⁻¹. Two SB-MBBRs operated in series was shown to be the superior strategy for achieving TAN compared to a single SB-MBBR with extended aerobic operation. By operating two SB-MBBRs in series, competition between autotrophic nitrifiers and heterotrophs is averted, and AOB proliferate in the biofilm, achieving TAN oxidation. Since TAN oxidation is likely achieved through partial nitrification, the SB-MBBR technology may be incorporated in a deammonification treatment train. The overall study presents novel information for the SB-MBBR design and operation, along with biofilm and microbiome fundamental findings that will guide future pilot- and full-scale applications of the SB-MBBR to treat cheese production wastewater.

Curd syneresis, a critical step in cheesemaking, directly influences the quality of cheese. The syneresis process is empirically controlled in cheese manufacturing plants. A sensor technology for this step would improve process control and enhance cheese quality. A light backscatter sensor with a Large Field of View (LFV) was tested using a central composite design over a broad range of cheese process conditions including milk pH, calcium chloride addition level, milk fat to protein ratio, temperature, and a cutting time factor (β). The research objectives were to determine if the LFV sensor could monitor coagulation and syneresis steps and provide information for predicting pressed curd moisture. Another objective was to optimize cheese yield and quality. The LFV sensor was found to monitor coagulation and syneresis and provide light backscatter information for predicting curd moisture content. A model for relating final curd moisture content with light backscatter response was developed and tested. Models for predicting whey fat losses, pressed curd moisture, and cheese yield were successfully developed (R2>0.75) using the test factors as independent variables. This was the first attempt to develop a technology for controlling pressed curd moisture using a sensor to monitor the syneresis step.

[Truncated abstract] It is well known that cows produce more milk if they are comfortable at milking, because stress from milking may cause them milk ejection problems. Temperament is an intrinsic characteristic of the animals so may affect the level of comfort at milking, and stress from the milking process itself may have a greater impact on animals with nervous temperament than on those of nervous temperament. When the milking becomes a stressor, it may affect secretion of milk ejection hormones that, in turn, may affect milk yield and composition. There is little evidence for how animal temperament affects milk quality in different farm animals. In this thesis, I have examined the effects of temperament on quantity and quality of the milk from Merino ewes and Holstein cows. I also tested whether temperament affected the processing performance (clotting properties) of the milk from Merino ewes. The general hypotheses tested were: 1. Calm ewes would produce more milk of better quality than nervous ewes, and, consequently, the clotting properties would be better in the milk from calm ewes than from nervous ewes. 2. Calm cows would produce more milk of better quality than nervous cows.

The aim of this thesis is a project documentation of a farm. It is a new building of stable for cow breeding and other buildings necessary for the proper function of the farm. The farm is located in Šalgovce, district of Topoľčany. The project documentation consists of administration building, milking parlor and a stable for cows. All objects are single building objects. . A base - administration building is the brick object with two floors. On the ground floor there is a lodge, a rest area for employees, cheese production area and a farm store. On the second floor there are offices. The milking parlor is the single building object with rooms necessary to secure stable operation. The stable is designed for a maximum of 172 cows.

Cheese is one of the most well known food products in the world dating back to the 8th century B.C. There are more than 2000 varieties of cheese that are manufactured all over the world. Feta cheese is a soft white cheese with a salty and slightly acidic taste, which has originated from Greece. Most of the feta cheese manufactured in Greece is consumed locally, the migration of greeks to other parts of the world led to a demand for feta cheese outside of Greece. The spreading of the popularity of feta cheese to other ethnic groups in different parts of the world resulted in the high demand for feta cheese worldwide. The modern and most efficient method of feta cheese production involves a membrane filtration method, known as ultrafiltration. The ultrafiltration process utilises pressure as a driving force to concentrate milk by removal of water and small dissolved molecules. Hollow fibre and spiral wound ultrafiltration membranes are the two types of membranes that are commonly used for cheese production. An extensive amount of research exists on the implementation of ultrafiltration to improve the efficiency of the cheese making process and the performance of the membranes. However, limited research has been conducted on the comparison of the hollow fibre and spiral wound membrane performance in the cheese making process. The objective of the research was to determine if the hollow fibre membranes used at Puhoi Valley Cheese can be replaced with spiral wound membranes without compromising the quality of cheese produced. In order to achieve the objective, feta cheese was produced using hollow fibre and spiral wound ultrafiltration pilot plants. The operating performances of the hollow fibre and spiral wound membrane units were compared. To ensure that the quality of cheese is maintained, the cheese manufactured on the pilot plant units was analysed in terms of composition, microbiology, texture and sensory properties. The cheese made using the hollow fibre membrane pilot plant was compared with the reference sample from Puhoi Valley Cheese as they use hollow fibre membranes to produce feta cheese. The cheese made from the spiral wound membrane unit was also compared to that made by the hollow fibre membrane pilot plant unit. The operating parameters such as the inlet and outlet pressure, pressure difference along the membrane, transmembrane pressure, flow rate, recycle rate (bleed off rate), temperature and the run time were recorded. The operating parameters of the hollow fibre and spiral wound runs were compared with the data from Puhoi Valley Cheese. The quality of cheese made on the hollow fibre and spiral wound pilot plant units were evaluated in terms of composition, texture, microbiology and sensory properties. The composition was defined by the fat, protein, total solids and salt contents. The fat content was determined by utilising the modified Schmid-Bondzynski-Ratzlaff method, protein by the Kjeldahl method, total solids by using the air drying oven and salt percentage by the volhard method. The texture of the cheese was determined by the fracturability and hardness from the compression curve generated using the single bite compression test. The microbiological testing was performed according to New Zealand testing methods for E.Coli, Staphylococcus aureus, coliforms and yeast and mould. The difference from the control method was utilised for sensory evaluation. The acid degree value method was used to determine the lipase activity in feta cheese. It was found from the composition, texture and sensory analysis that the cheese from the hollow fibre pilot plant was different from the cheese manufactured at Puhoi Valley Cheeses (PVC). The spiral wound cheeses were also found to be different to PVC cheese, however the spiral wound cheeses and the pilot plant hollow fibre cheese were the same. The differences between both the pilot plant cheeses and PVC cheese were in terms of the fat, salt, moisture contents and the lipase activity in the cheeses. The fat content in the hollow fibre and spiral wound pilot plant cheeses are lower in comparison to the PVC cheese. This difference in fat content is considered to be due to the difference in the fat to protein ratio of the milk concentrated on the pilot plant and the PVC ultrafiltration system. The lower fat content resulted in firmer cheese than PVC due to more cross linking between the protein strands in cheese. The salt content in the cheeses made using the hollow fibre and spiral wound pilot plants was lower than Puhoi Valley Cheese. This is considered to be due to the low ratio of brine volume to cheese volume used for salting the cheese. The salt content of brine decreases during brining; hence a low ratio of brine volume to cheese volume causes a significant decrease in brine concentration. The decrease in brine concentration decreases the salt intake of the cheese. As salt diffuses in the moisture diffuses out, lower salt content results in higher moisture content in the cheese. As mentioned, the moisture content of the hollow fibre pilot plant cheese was higher than the PVC cheese. The moisture content is inversely proportional to the total solids, hence higher moisture in pilot plant cheeses implies lower total solids than the PVC cheese. The lipase activity results showed that the hollow fibre and spiral wound pilot plant cheeses had higher lipase activity than the Puhoi valley cheese. The differences in lipase activity of the pilot plant cheeses and Puhoi Valley cheese were considered to be due to the incomplete inactivation of lipase present in milk during pasteurisation. The results from texture and sensory evaluation support the above mentioned differences. The microbiology results for all pilot plant cheeses were within the trigger limits set by Puhoi valley cheeses. The results from monitoring the operating parameters of both the pilot plant data show that the permeate flux decreases while the total solids in milk increase with time, which was also observed from the Puhoi Valley Cheese data. However, the rate of decrease of the permeate flux and the increase of the total solids in milk are dependent on the membrane area, feed volume, transmembrane pressure, pressure drop across the membrane and the flow characteristics. The rate of decrease in permeate flux and the rate of increase in the total solids of the hollow fibre runs and spiral wound runs are slightly different. The difference is due to the availability of larger membrane surface area and processing of larger feed volume of milk in the spiral wound runs. The transmembrane pressure and the pressure drop across the membrane were maintained as close as possible to Puhoi Valley Cheese. In conclusion, spiral wound membranes can be used to achieve the desired total solids concentration and successfully make the same feta cheese as the hollow fibre pilot plant. In order to make the same quality of feta cheese as Puhoi Valley Cheese using the spiral wound membrane pilot plant, the same composition of milk used for concentration at Puhoi Valley Cheese needs to be used on the spiral wound pilot plant unit. It is recommended that Puhoi Valley Cheeses should be replaced with spiral wound membranes if they are more economical in terms of cost than the hollow fibre membranes.

Cheese is one of the most well known food products in the world dating back to the 8th century B.C. There are more than 2000 varieties of cheese that are manufactured all over the world. Feta cheese is a soft white cheese with a salty and slightly acidic taste, which has originated from Greece. Most of the feta cheese manufactured in Greece is consumed locally, the migration of greeks to other parts of the world led to a demand for feta cheese outside of Greece. The spreading of the popularity of feta cheese to other ethnic groups in different parts of the world resulted in the high demand for feta cheese worldwide. The modern and most efficient method of feta cheese production involves a membrane filtration method, known as ultrafiltration. The ultrafiltration process utilises pressure as a driving force to concentrate milk by removal of water and small dissolved molecules. Hollow fibre and spiral wound ultrafiltration membranes are the two types of membranes that are commonly used for cheese production. An extensive amount of research exists on the implementation of ultrafiltration to improve the efficiency of the cheese making process and the performance of the membranes. However, limited research has been conducted on the comparison of the hollow fibre and spiral wound membrane performance in the cheese making process. The objective of the research was to determine if the hollow fibre membranes used at Puhoi Valley Cheese can be replaced with spiral wound membranes without compromising the quality of cheese produced. In order to achieve the objective, feta cheese was produced using hollow fibre and spiral wound ultrafiltration pilot plants. The operating performances of the hollow fibre and spiral wound membrane units were compared. To ensure that the quality of cheese is maintained, the cheese manufactured on the pilot plant units was analysed in terms of composition, microbiology, texture and sensory properties. The cheese made using the hollow fibre membrane pilot plant was compared with the reference sample from Puhoi Valley Cheese as they use hollow fibre membranes to produce feta cheese. The cheese made from the spiral wound membrane unit was also compared to that made by the hollow fibre membrane pilot plant unit. The operating parameters such as the inlet and outlet pressure, pressure difference along the membrane, transmembrane pressure, flow rate, recycle rate (bleed off rate), temperature and the run time were recorded. The operating parameters of the hollow fibre and spiral wound runs were compared with the data from Puhoi Valley Cheese. The quality of cheese made on the hollow fibre and spiral wound pilot plant units were evaluated in terms of composition, texture, microbiology and sensory properties. The composition was defined by the fat, protein, total solids and salt contents. The fat content was determined by utilising the modified Schmid-Bondzynski-Ratzlaff method, protein by the Kjeldahl method, total solids by using the air drying oven and salt percentage by the volhard method. The texture of the cheese was determined by the fracturability and hardness from the compression curve generated using the single bite compression test. The microbiological testing was performed according to New Zealand testing methods for E.Coli, Staphylococcus aureus, coliforms and yeast and mould. The difference from the control method was utilised for sensory evaluation. The acid degree value method was used to determine the lipase activity in feta cheese. It was found from the composition, texture and sensory analysis that the cheese from the hollow fibre pilot plant was different from the cheese manufactured at Puhoi Valley Cheeses (PVC). The spiral wound cheeses were also found to be different to PVC cheese, however the spiral wound cheeses and the pilot plant hollow fibre cheese were the same. The differences between both the pilot plant cheeses and PVC cheese were in terms of the fat, salt, moisture contents and the lipase activity in the cheeses. The fat content in the hollow fibre and spiral wound pilot plant cheeses are lower in comparison to the PVC cheese. This difference in fat content is considered to be due to the difference in the fat to protein ratio of the milk concentrated on the pilot plant and the PVC ultrafiltration system. The lower fat content resulted in firmer cheese than PVC due to more cross linking between the protein strands in cheese. The salt content in the cheeses made using the hollow fibre and spiral wound pilot plants was lower than Puhoi Valley Cheese. This is considered to be due to the low ratio of brine volume to cheese volume used for salting the cheese. The salt content of brine decreases during brining; hence a low ratio of brine volume to cheese volume causes a significant decrease in brine concentration. The decrease in brine concentration decreases the salt intake of the cheese. As salt diffuses in the moisture diffuses out, lower salt content results in higher moisture content in the cheese. As mentioned, the moisture content of the hollow fibre pilot plant cheese was higher than the PVC cheese. The moisture content is inversely proportional to the total solids, hence higher moisture in pilot plant cheeses implies lower total solids than the PVC cheese. The lipase activity results showed that the hollow fibre and spiral wound pilot plant cheeses had higher lipase activity than the Puhoi valley cheese. The differences in lipase activity of the pilot plant cheeses and Puhoi Valley cheese were considered to be due to the incomplete inactivation of lipase present in milk during pasteurisation. The results from texture and sensory evaluation support the above mentioned differences. The microbiology results for all pilot plant cheeses were within the trigger limits set by Puhoi valley cheeses. The results from monitoring the operating parameters of both the pilot plant data show that the permeate flux decreases while the total solids in milk increase with time, which was also observed from the Puhoi Valley Cheese data. However, the rate of decrease of the permeate flux and the increase of the total solids in milk are dependent on the membrane area, feed volume, transmembrane pressure, pressure drop across the membrane and the flow characteristics. The rate of decrease in permeate flux and the rate of increase in the total solids of the hollow fibre runs and spiral wound runs are slightly different. The difference is due to the availability of larger membrane surface area and processing of larger feed volume of milk in the spiral wound runs. The transmembrane pressure and the pressure drop across the membrane were maintained as close as possible to Puhoi Valley Cheese. In conclusion, spiral wound membranes can be used to achieve the desired total solids concentration and successfully make the same feta cheese as the hollow fibre pilot plant. In order to make the same quality of feta cheese as Puhoi Valley Cheese using the spiral wound membrane pilot plant, the same composition of milk used for concentration at Puhoi Valley Cheese needs to be used on the spiral wound pilot plant unit. It is recommended that Puhoi Valley Cheeses should be replaced with spiral wound membranes if they are more economical in terms of cost than the hollow fibre membranes.

Cheese is one of the most well known food products in the world dating back to the 8th century B.C. There are more than 2000 varieties of cheese that are manufactured all over the world. Feta cheese is a soft white cheese with a salty and slightly acidic taste, which has originated from Greece. Most of the feta cheese manufactured in Greece is consumed locally, the migration of greeks to other parts of the world led to a demand for feta cheese outside of Greece. The spreading of the popularity of feta cheese to other ethnic groups in different parts of the world resulted in the high demand for feta cheese worldwide. The modern and most efficient method of feta cheese production involves a membrane filtration method, known as ultrafiltration. The ultrafiltration process utilises pressure as a driving force to concentrate milk by removal of water and small dissolved molecules. Hollow fibre and spiral wound ultrafiltration membranes are the two types of membranes that are commonly used for cheese production. An extensive amount of research exists on the implementation of ultrafiltration to improve the efficiency of the cheese making process and the performance of the membranes. However, limited research has been conducted on the comparison of the hollow fibre and spiral wound membrane performance in the cheese making process. The objective of the research was to determine if the hollow fibre membranes used at Puhoi Valley Cheese can be replaced with spiral wound membranes without compromising the quality of cheese produced. In order to achieve the objective, feta cheese was produced using hollow fibre and spiral wound ultrafiltration pilot plants. The operating performances of the hollow fibre and spiral wound membrane units were compared. To ensure that the quality of cheese is maintained, the cheese manufactured on the pilot plant units was analysed in terms of composition, microbiology, texture and sensory properties. The cheese made using the hollow fibre membrane pilot plant was compared with the reference sample from Puhoi Valley Cheese as they use hollow fibre membranes to produce feta cheese. The cheese made from the spiral wound membrane unit was also compared to that made by the hollow fibre membrane pilot plant unit. The operating parameters such as the inlet and outlet pressure, pressure difference along the membrane, transmembrane pressure, flow rate, recycle rate (bleed off rate), temperature and the run time were recorded. The operating parameters of the hollow fibre and spiral wound runs were compared with the data from Puhoi Valley Cheese. The quality of cheese made on the hollow fibre and spiral wound pilot plant units were evaluated in terms of composition, texture, microbiology and sensory properties. The composition was defined by the fat, protein, total solids and salt contents. The fat content was determined by utilising the modified Schmid-Bondzynski-Ratzlaff method, protein by the Kjeldahl method, total solids by using the air drying oven and salt percentage by the volhard method. The texture of the cheese was determined by the fracturability and hardness from the compression curve generated using the single bite compression test. The microbiological testing was performed according to New Zealand testing methods for E.Coli, Staphylococcus aureus, coliforms and yeast and mould. The difference from the control method was utilised for sensory evaluation. The acid degree value method was used to determine the lipase activity in feta cheese. It was found from the composition, texture and sensory analysis that the cheese from the hollow fibre pilot plant was different from the cheese manufactured at Puhoi Valley Cheeses (PVC). The spiral wound cheeses were also found to be different to PVC cheese, however the spiral wound cheeses and the pilot plant hollow fibre cheese were the same. The differences between both the pilot plant cheeses and PVC cheese were in terms of the fat, salt, moisture contents and the lipase activity in the cheeses. The fat content in the hollow fibre and spiral wound pilot plant cheeses are lower in comparison to the PVC cheese. This difference in fat content is considered to be due to the difference in the fat to protein ratio of the milk concentrated on the pilot plant and the PVC ultrafiltration system. The lower fat content resulted in firmer cheese than PVC due to more cross linking between the protein strands in cheese. The salt content in the cheeses made using the hollow fibre and spiral wound pilot plants was lower than Puhoi Valley Cheese. This is considered to be due to the low ratio of brine volume to cheese volume used for salting the cheese. The salt content of brine decreases during brining; hence a low ratio of brine volume to cheese volume causes a significant decrease in brine concentration. The decrease in brine concentration decreases the salt intake of the cheese. As salt diffuses in the moisture diffuses out, lower salt content results in higher moisture content in the cheese. As mentioned, the moisture content of the hollow fibre pilot plant cheese was higher than the PVC cheese. The moisture content is inversely proportional to the total solids, hence higher moisture in pilot plant cheeses implies lower total solids than the PVC cheese. The lipase activity results showed that the hollow fibre and spiral wound pilot plant cheeses had higher lipase activity than the Puhoi valley cheese. The differences in lipase activity of the pilot plant cheeses and Puhoi Valley cheese were considered to be due to the incomplete inactivation of lipase present in milk during pasteurisation. The results from texture and sensory evaluation support the above mentioned differences. The microbiology results for all pilot plant cheeses were within the trigger limits set by Puhoi valley cheeses. The results from monitoring the operating parameters of both the pilot plant data show that the permeate flux decreases while the total solids in milk increase with time, which was also observed from the Puhoi Valley Cheese data. However, the rate of decrease of the permeate flux and the increase of the total solids in milk are dependent on the membrane area, feed volume, transmembrane pressure, pressure drop across the membrane and the flow characteristics. The rate of decrease in permeate flux and the rate of increase in the total solids of the hollow fibre runs and spiral wound runs are slightly different. The difference is due to the availability of larger membrane surface area and processing of larger feed volume of milk in the spiral wound runs. The transmembrane pressure and the pressure drop across the membrane were maintained as close as possible to Puhoi Valley Cheese. In conclusion, spiral wound membranes can be used to achieve the desired total solids concentration and successfully make the same feta cheese as the hollow fibre pilot plant. In order to make the same quality of feta cheese as Puhoi Valley Cheese using the spiral wound membrane pilot plant, the same composition of milk used for concentration at Puhoi Valley Cheese needs to be used on the spiral wound pilot plant unit. It is recommended that Puhoi Valley Cheeses should be replaced with spiral wound membranes if they are more economical in terms of cost than the hollow fibre membranes.

Made available in DSpace on 2017-07-10T17:44:32Z (GMT). No. of bitstreams: 1 Ionara_Casali_Tesser.pdf: 1148142 bytes, checksum: add103337d6fede6befb681a6c9622c9 (MD5) Previous issue date: 2014-07-25 / Coordenação de Aperfeiçoamento de Pessoal de Nível Superior / Three municipalities from the west of the Cantuquiriguaçu region (Paraná state) were chosen to this study, which examined the production and centesimal composition of the colonial cheese produced in the region. The research also aimed provide to the actors involved in the process knowledge concerning the production and improvements of the cheese in order to guarantee the quality of the product and support the rural worker that performs this activity. 17 rural properties were visited and were applied a survey questionnaire in order to understand the milk production and the production conditions of the cheese. Following the Normative Instruction nº 30/2013 from MAPA (Brazilian Ministry of Agriculture, Livestock and Food Supply), microbiological and compositional analyses were made on the cheese from the visited properties aiming to typify the artisanal colonial cheese produced on those municipalities. The results will become important supports to the adoption of municipal public policies intending not only the continuity of the production, and its improvement, but also the consumers safety / Três municípios do Oeste da Cantuquiriguaçu/PR foram escolhidos para este estudo que investigou a fabricação e composição centesimal do queijo colonial produzido nessa região. Teve também por objetivo possibilitar aos atores envolvidos no processo os conhecimentos referentes sobre sua própria produção para que melhorias pudessem ser implantadas visando à qualidade do queijo e o apoio ao produtor rural que trabalha nesta atividade. Foram visitadas 17 propriedades para aplicação de um questionário, visando conhecer a produção do leite e condições de fabricação dos queijos. Através da Instrução normativa nº30/2013 do MAPA (Ministério da Agricultura, Pecuária e Abastecimento), juntamente com esse processo foram realizadas análises microbiológicas e composicional dos queijos coloniais das propriedades visitas para caracterizar o queijo colonial artesanal produzido nos municípios avaliados. Estes resultados serão subsídios importantes para a adoção de políticas públicas no município que visem não apenas à continuidade da produção, ou à melhoria da produção do queijo colonial, mas também à segurança dos consumidores