The supply of electricity is important in modern society, so the outages of the electric grid should be few and short, especially for the transmission grid. A summary of the history of the Swedish electrical system is presented. The objective is to be able to plan the maintenance better by following the condition of the equipment. The risk matrix can be used to choose which component to be maintained. The risk matrix is improved by adding a dimension, the uncertainty of the probability. The risk can be reduced along any dimension: better measurements, preventive maintenance or more redundancy. The number of dimensions can be reduced to two by following iso-risk lines calculated for the beta distribution. This thesis lists twenty surveys about circuit breakers and disconnectors, with statistics about the failures and the lifetime. It also presents about forty condition-measuring methods for circuit breakers and disconnectors, mostly applicable to the electric contacts and the mechanical parts. A method for scheduling thermography based on analysis of variance of the current is tried. Its aim is to reduce the uncertainty of thermography and it is able to explain two thirds of the variation using the time of the day, the day of the week and the week number as explanatory variables. However, the main problem remains as the current is in general too low. A system with IR sensors has been installed at the nine contacts of six disconnectors with the purpose of avoiding outages for maintenance if the contacts are in a good condition. The measured temperatures are sent by radio and regressed against the square of the current, the best exponent found. The coefficient of determination $R^2$ is high, greater than 0.9. The higher the regression coefficient is, the more heat is produced at the contact. So this ranks the different contacts. Finally a framework for lifetime modelling and condition measuring is presented. Lifetime modelling consists in associating a distribution of time to failure with each subpopulation. Condition measuring means measuring a parameter and estimating its value in the future. If it exceeds a threshold, maintenance should be carried out. The effect of maintenance of the contacts is shown for four disconnectors. An extension of the risk matrix with uncertainty, a survey of statistics and condition monitoring methods, a system with IR sensors at contacts, a thermography scheduling method and a framework for lifetime modelling and condition measuring are presented. They can improve the planning of outages for maintenance. Finally a framework for lifetime modelling and condition measuring is presented. Lifetime modelling consists in associating a distribution of time to failure with each subpopulation. Condition measuring means measuring a parameter and estimating its value in the future. If it exceeds a threshold, maintenance should be carried out. The effect of maintenance of the contacts is shown for four disconnectors. An extension of the risk matrix with uncertainty, a survey of statistics and condition monitoring methods, a system with IR sensors at contacts, a thermography scheduling method and a framework for lifetime modelling and condition measuring are presented. They can improve the planning of outages for maintenance. / Elförsörjningen är viktig i det moderna samhället, så avbrotten bör vara få och korta, särskilt i stamnätet. En kortfattad historik över det svenska elsystemet presenteras. Målet är att kunna planera avbrotten för underhåll bättre genom att veta mera om apparaternas skick. Det är svårt att planera avbrott för underhåll och utbyggnad. Riskmatrisen är verktyg för att välja vad som ska underhållas och den kan förbättras genom att lägga till en dimension, sannolikhetens osäkerhet. Risken kan minskas längs med varje dimension: bättre mätningar, förebyggande underhåll och mer redundans. Antalet dimensioner kan igen bli två genom att följa linjer med samma risk, som är beräknade för betafördelningen. Denna avhandling tar upp tjugo studier av fel i brytare och frånskiljare med data om felorsak och livslängd. Den har också en översikt av ett fyrtiotal olika metoder för tillståndsmätningar för brytare och frånskiljare, som huvudsakligen rör de elektriska kontakterna och de mekaniska delarna. Ett system med IR sensorer har installerats på de nio kontakterna på sex frånskiljare. Målet är att minska antalet avbrott för underhåll genom att skatta skicket när frånskiljarna är i drift. De uppmätta temperaturerna tas emot genom radio och behandlas genom regression mot kvadraten av strömmen, då den bästa exponenten för strömmen visade sig vara 2,0. Förklaringsfaktorn $R^2$ är hög, över 0,9. För varje kontakt ger det en regressionskoefficient. Ju högre koefficienten är, desto mer värme utvecklas det i kontakten, vilket kan leda till skador på materialet. Koefficienterna ger en rangordning av frånskiljarna. Systemet kan också användas för att minska eller öka den tillåtna strömmen baserat på skicket. Slutligen förklaras ett ramverk för livslängdsmodellering och tillståndsmätning. Livslängdsmodellering innebär att koppla en fördelning för tiden till fel med varje delpopulation. Med tillståndsmätning avses att mäta en parameter och skatta dess värde i framtiden. Om den överskrider en tröskel, måste apparaten underhållas. Effekten av underhåll visas för fyra frånskiljare. En utveckling av riskmatrisen med osäkerheten, en sammanställning av statistik och metoder för tillståndsövervakning, ett system med IR-sensor vid kontakerna, en metod för termografiplanering och ett ramverk för livslängdsmodellering och tillståndsmätningar presenteras. De kan förbättra avbrottsplaneringen. / El suministro de energía eléctrica es importante en la sociedad moderna. Por eso los cortes eléctricos deben ser poco frecuentes y de poca duración, sobre todo en la red de transmisión. Esta tesis resume la historia del sistema eléctrico sueco. El objetivo es planificar los cortes mejor siguiendo la condición de los aparatos. La matriz de riesgo se utiliza muchas veces para escoger en qué aparatos debería realizarse mantenimiento. Esta matriz se puede mejorar añadiendo una dimensión: la incertidumbre de la probabilidad. El riesgo puede ser disminuido siguiendo cada una de las tres dimensiones: mejores mediciones, mantenimiento preventivo y mayor redundancia. El número de dimensiones puede reducirse siguiendo líneas del mismo riesgo calculadas para la distribución beta. Esta tesis presenta veinte estudios de fallos en interruptores y seccionadores con datos sobre la causa y el tiempo hasta la avería. Contiene también una visión general de cuarenta métodos para medir la condición de seccionadores e interruptores, aplicables en su mayoría a los contactos eléctricos y los componentes mecánicos. Se ha instalado un sistema con sensores infrarrojos en los seis contactos de nueve seccionadores. El objetivo es disminuir los cortes de servicio para mantenimiento, estimando la condición con el seccionador en servicio. Las temperaturas son transmitidas por radio y se hace una regresión con el cuadrado de la corriente, ya que el mejor exponente de la corriente resultó ser 2,0. $R^2$ alcanza un valor de 0,9 indicando un buen ajuste de los datos por parte del modelo. Existe un coeficiente de regresión para cada contacto y este sirve para ordenar los contactos según la necesidad de mantenimiento, ya que cuanto mayor sea el coeficiente más calor se produce en el contacto. Finalmente se explica que el modelado de tiempo hasta la avería consiste en asignar una distribución estadística a cada equipo. La monitorización del estado consiste en medir y estimar un parámetro y luego predecir su valor en el futuro. Si va a sobrepasar un cierto límite, el equipo necesitará de mantenimiento. Se presenta el efecto de mantenimiento de cuatro seccionadores. Un desarrollo de la matriz de riesgo, un conjunto de estadísticas y métodos de monitoreo de condición, un sistema de sensores IR situados cerca de los contactos, en método de planificación de termografía y un concepto para explicar la modelización de tiempo hasta la avería y de la monitorización de la condición han sido presentados y hace posible una mejor planificación de los cortes de servicio. / <p>QC 20170928</p>

My thesis is focused on realization of three inrush current limitors samples. This limiters will be used in ABB´s metal-clad, air-insulated switchgears for medium voltage distribution. On the basis of the results there is chosen the sample with optimal properties suitable for practice in the conclusion.

The aim of the project was to prepare the given model of the current path in the environment of the SolidWorks programme, in order to simulate the flow path in the environment of the Ansys programme, where there was calculated the distribution of current density,voltage drops and heat loss on the the specified current track according to specified conditions. The obtained results are analyzed at the conclusion of this work.

This work deals with the calculation of forces acting on a current carrying path breakers, namely op type BC160 fy Letohrad. There is described the principle of electrodynamic forces and calculation of these forces for different current carrying path. Finally, a simplified model is created by using a circuit breaker simulation program and then forces that arise during the passage of a current are calculated.

Nowadays there are electronic systems almost in every new device. They are emitting and receiving electromagnetic interferences. The safety levels for circuit breakers are also increasing. Because of these issues the circuit breakers must work properly also in areas filled by electromagnetic interference. This thesis describes the issues of electromagnetic susceptibility of the circuit breakers.

The thesis is focused on the calculation of electrodynamic forces that counterwork on moving contacts of compact circuit breaker BL1600 from the company OEZ Letohrad. The thesis is divided into separates chapters that build on themselves. In the introduction the reason why we deal with calculation of dynamic forces and structural arrangement of current carrying path is described. In the following chapter there is a theoretical analysis of electrodynamic forces that conterwork on individual parts of circuit breaker´s element. The third part is devoted to structural arrangement of the circuit breaker BL1600. In this part we can find an example of using the circuit broker Modeion in practice. Two next chaptures deal with adjustment of the model of current carrying path which then serves for the calculation of electrodynamic forces. The rest of the thesis is devoted to my own calculations. These calculations are mainly stationary where we try to find the forces that conterwork on the contacts in a steady current and in a point in time. There are also dynamics calculation when we can watch the forces that counterwork on contacts in a certain time interval. The last chapter is devoted to a stationary calculation of forces that counterwork on the electrical arc which arises while turning the short-circuit current off. The obtained results are evaluated in partial conclusions of this thesis.

This master‘s thesis deals with the thermal overload trip unit in automatically operated electrical switching devices. The first part of this thesis serves as a basis for a design of thermostatic bimetal element in electrical switching device. The thesis presents important parameters and calculation principles needed for the design of bimetal element. The thesis further describes the operating principle of thermal trip unit and its possible design solutions. The main part is devoted to analytical calculation and measurement of specific thermostatic bimetal type contained in thermal trip unit of molded case circuit breaker. It is measurement of force and deflection, depending on temperature change. In the next part a numerical model of the bimetallic strip was created and its deflection was simulated. The analytical results are compared with the measured and simulated results at the end of the thesis.

This master’s thesis deals with the calculation of electrodynamic forces breaker BD250NE305. Main tasks in this semester project is to study the theoretical analysis of individual parts specified breakers. Processing theoretical analysis of these forces. Creating a 3D model current path and sheets quenching chamber single phase circuit breaker in Autodesk Inventor Professional 2012. Another challenge is the subsequent export the model into the simulation program ANSYS Maxwell. After simulation, the specified conditions must be processed and the results of the present work is to evaluate.

The aim of this thesis is to simulate the action of electrodynamic forces on current carrying path and a movable contact of the circuit breaker OEZ Modeion BH 630NE. For the calculation there is used the simulation program Ansys Maxwell. The first part is devoted to theoretical analysis of electromagnetic forces on a conductor in a magnetic field. Further I discuss the constructional design of the circuit breaker itself, especially the current path and the contact mechanism. In the next part there is (with using program Autodesk Inventor) created a simplified 3D model of the current path including an arc chamber. With program Ansys Maxwell then there is performed simulation of the acting of forces in each mode. This is magnetostatic and transient analysis for symmetrical and asymmetrical flow of the fault current. In conclusion the results obtained are evaluated and processed in the tabular way.

The aim of the present thesis is to improve and optimize a Thomson coil based actuatorfor medium voltage vacuum interrupters. The Thomson coil based actuator’s concept isdiscussed. The thesis presents analytical as well as finite element models of the actuatoralong with a comparison of their results. Several experimental setups have been built forthis degree project and they are described in the thesis. Measurements from these setupsare also compared to simulation results. The thesis concludes by drawing conclusionsfrom the compared results and proposes possible directions for additional work in thenear future. / Målsättningen för denna uppsats är att förbättra och optimera en aktuator för mellanspänningsvakuumbrytare baserad på en Thomsonspole. Aktuatorkonceptet analyserasoch diskuteras. Uppsatsen presenterar analytiska modeller såväl som numeriska modellerför FEM av aktuatorn, samt jämförelser av resultaten från simuleringar gjorda av dessa.Flera experimentuppställningar har byggts under detta examensprojekt och beskrivs idenna uppsatsen. Mätningar från dessa uppställningar jämförs också med resultaten frånsimuleringarna. Uppsatsen drar slutligen slutsatser utifrån resultaten och föreslår möjligavägar för ytterligare arbete på området inom en snar framtid.