Thesis (M.A.)--Slippery Rock University, 2001. / Title from title screen (viewed April 16, 2002). Last updated Apr. 2002.

This study was carried out on the main coal-producing and the extensively block-faulted area of Mchenga Coal Mine, southeast of the 90 km2 intracratonic Livingstonia Coalfield in the north of Malawi. It was initiated against the background of indistinct information on coal geology, shortage of energy and potential environmental threats due to mine activities. The study aimed at integrating investigations of characterization of the lithostratigraphy, coal seam correlation, coal quality determination, examination of the mineralogy and geochemistry of coal and hosts rocks, assessment of water quality and providing information for mining and potential environmental and water quality impact assessment in the study area. The methodologies used in this study include literature review, field visits, mapping, sites selection and characterization, borehole logging, geochemical analyses, data processing and interpretation. The geochemical analyses include proximity analysis of coal quality, microscopy and X-ray Diffraction for mineralogy and petrology, X-ray Fluorescence (XRF) for rock geochemistry and Atomic Absorption Spectrometry for determination water geochemistry. The results have shown that a) The Coal Measures comprises of four to six coal seams in different localities, and the occurrence is flat and gently dipping southeast and are correlated. Thicknesses of the coal seams vary from 0.10m to 3.0m with some notable lateral and horizontal variations. Thick and workable seams occupy the lower portion of the Coal Measures and are exposed along the North Rumphi River bank; b) Coal quality belongs to sub-bituminous ‘A’ to ‘C’ on ASTM classification (1991), being characterised by low moisture content (0.8 to 1.3 wt percent) and sulphur content (0.49 to 0.85 wt percent), high ash content (9.0 to 17 wt percent) and volatile matter (24 to 32.9 wt percent), fixed carbon (53.6 to 62.6 wt percent), calorific value (7,015 to 7,670 kcal/kg); c) Mineral matters constitute approximately 9.55 to 38.34 wt percent of the coal samples, predominantly clays (interstratified illite/smectite and kaolinite) with varying proportions of quartz, mica and feldspars, as well as minor calcite and pyrite and their geochemistry, being characterised by enrichment of SiO2 from 5.37 to 20.56 wt percent, Al2O3 (2.63 to 11.21 wt percent) and K2O (0.32 to 3.65 wt percent) with trace concentrations of CaO (0.04 to 0.41 wt. percent), MgO (0.08 to 0.65 wt percent) and P2O5 (0.018 to 0.037 wt percent) and Na2O concentration notably below 0.01 wt percent; d) Calcite and pyrite constitute minor concentration in both sandstones and shales; e) Water quality in the area is characterised as two groups of acidic (pH 3.3-6.4) and near-neutral to slightly alkaline (pH 6.9-7.3) and low pH, high TDS, SO42- and EC are noted at the coal crusher plant which points out to high leaching of trace elements such as Pb and Fe. Na++K+ are dominant in upper sections of North Rumphi and Mhlepa Rivers. Ca2+ cations are dominant at crusher plant, underground mine and lower section of Mhlepa; f) Based on the geochemistry analysis, Na and trace elements such as Ti, V, Mn, Fe, Zn, Rb, Sr and Zr from coal and host rocks have the ability to contribute significantly to deterioration in the ground and surface water quality in the study area. It can be concluded that the coals of the Livingstonia Coalfield belong to Gondwana group deposited in sub-basin with multiple seams embedded in sandstone and shale host rocks.

Market efficiency and buyers' risk strategy in the Japanese coking coal import market are examined. The Japanese coal market is found to be inefficient, Japanese buyers traditionally have purchased coals from the United States at a high price and, since the second half of the 1980's, have paid the highest average price to Canadian producers. Given the abundant low cost Australian coals, this purchasing pattern does not meet the cost minimization criteria for efficiency. This is explained mainly by the buyers' risk management strategy. To more accurately examine price differentiation, the complexity of coal quality is considered first. A statistical method is used to estimate the quality premium as a cost component in price formation. Next a comparison of supply regions and a detailed investigation on market conduct is based on quality-adjusted prices, which are assumed to represent the prices of homogenous coals. Although various reasons are used by researchers to explain Japanese buyers power, this study finds vertical integration of the Japanese companies to be the most important factor creating that power. A detailed survey of vertical integration is made. Finally, a monetary value of the risk premium is estimated by using the partial elasticity of substitution. Total payments by Japanese coking coal buyers for risk premiums are estimated. These represent the extra dollars paid by the Japanese to US and Canadian coal producers for purchasing their coals instead of Australian coals.

Coal quality plays a crucial role both economically and environmentally in the operation of a coal-fired power plant. These plants are designed to operate most efficiently when coal of consistently good quality is used as the feed. For example, the ash content should be monitored to control slagging problems in the burners. For emission control purposes the sulfur content of the feed should be carefully scrutinized. This realization of the importance of coal quality to the end-user has made the prediction of coal quality an important concern. Computerized mine planning systems can be used to help suppliers predict the quality of future coal shipments. One such system was implemented at an underground coal mine to determine its performance in an operating environment. Following some extensive revisions to the system, the results of the implementation exercise showed the ability of this mine planning system to account for coal quality while producing a workable short-range plan. To be of direct use to the end-user, the mine planning results should be adjusted to account for mining dilution and subsequent beneficiation of the run-of-mine coal. To help power plant owners in predicting the quality of the power plant feed a computer program was developed to solve the blending problem faced by plants dependent on multiple sources of supply. This interactive program utilizes the predictions from the mine planning system to obtain a goal programming formulation of the blending problem. This type of problem formulation gives the program the flexibility needed to solve the blending problem in both long and short term time frames. Use of the program in both planning scenarios was illustrated by examples. The results showed the ability of the program to determine the best blend possible based on a set of user-specified objectives. Use of this interactive blending program in conjunction with the mine planning system provides the capability of computerized prediction of coal quality from mine mouth to blended plant feed. Implementation of these planning aids on a routine basis will assist the owners of coal-fired power plants in their attempts to maximize plant efficiency and maintain environmental standards.

A research report submitted to the School of Chemical and Metallurgical Engineering, Faculty of Engineering and the Built Environment, University of the Witwatersrand, Johannesburg, 2016. / The self-heating of coals is a complex problem which has been occurring for centuries. This problem has been fatal to coal miners, an economical challenge to coal mines and a health risk in a release of greenhouse gases to the public in general. Therefore, everyone is affected by the self-heating of coal, which leads to spontaneous combustion when the ignition temperature is reached. There are many test methods that have been used to test spontaneous combustion in coal, but all have one common factor or disadvantage of requiring long periods of time before a conclusion can be deduced. This then creates a need for a rapid and reliable method to test the liability of coal to self-heat in the coal industry and thus the motivation for this project. The thermogravimetry analysis (TGA) method was selected to test the liability of coal to self-heat due to its short analytical duration. The Smith-Glasser oxidation test was selected to validate the TGA results obtained. The main aim of this project is to investigate the reliability of the TGA method to predict the propensity of coal to self-heat. 29 samples from different regions of South Africa were used, prepared to 250 μm for all the analyses and self-heating tests. All samples were analysed for proximate, calorific value, sulphur and petrographic properties before the spontaneous combustion liability tests began. The TGA method followed two tests: 1) the O2 adsorption and 2) the ignition test. Five different heating rates (3, 5, 7, 10, and 20) °C/min were run in order to obtain five derivative slopes which would be used to obtain the TGspc index. The oxygen adsorption test studies the mass increase at low temperature under exposure of air between the temperature ranges of 100 – 300°C. The Smith-Glasser oxidation test method studies the reaction of coal with O2 and calculates the O2 absorbed per amount of coal tested. The Smith-Glasser test results collaborated with most of the other analytical results, and with the TGA results to a certain extent. The TGA spontaneous combustion liability test requires additional analytical work to back up its results because the results do not appear as accurate as the Smith-Glasser oxidation test. It also requires repeatability tests to ensure the integrity of the results. / EM2017

M.P.H., Faculty of Health Sciences, 2008 / Introduction The Department of Minerals and Energy (DME) in South Africa issued a Directive B7, titled “A Guideline for the Ventilating of Mechanical Miner Sections” to the coal mining industry. The main purpose of this directive was to reduce respirable dust exposures at the coal face with the long term objective of reducing the incidence of Coal Workers Pneumoconiosis (CWP). This study attempts to evaluate the appropriateness of the DME approach by comparing respirable coal dust results from personal samples from occupations at the coal face to the results obtained from engineering samples at the continuous miner. Objectives The objectives of this study are to: • Describe personal respirable coal dust concentrations of the occupations within the continuous miner Homogeneous Exposure Group (HEG) in five underground coal mines in Mpumalanga from January 2005 to December 2006. • Describe environmental engineering respirable coal dust concentrations of the continuous miner operator position in five underground coal mines in Mpumalanga from January 2005 to December 2006. • Compare personal respirable coal dust concentrations to Environmental Engineering Dust (EED) concentrations in five coal mines in Mpumalanga from January 2005 to December 2006. Methodology This study is descriptive in nature and was carried out utilizing historical respirable coal dust data from underground coal bord and pillar production sections. Data was supplied by Collieries Environmental Control Services (CECS) who provided a coal sampling and analysis service to South African collieries. Data provided was from five large underground coal mines in the Mpumalanga coal fields. The study population consisted of occupations within the HEG of workers deployed at the coal face who were linked to Continuous Miner (CM) production activities and results from EED sampling. Results When comparing the personal sampling results to EED sampling results for each individual mine, it is evident that all the mines had lower personal sampling results than EED results, thus establishing a definite trend. When combining all the mines in the two data sets it is also evident that EED sampling results are significantly higher than personal sampling results confirming the trend observed on individual mines. Correlation tests carried out between the two data sets indicated that there is no correlation between the personal and EED sampling results. The poor correlation between the two data sets indicates that the EED sampling position is not ideal and does not take account of the actual contaminant levels leaving the coal-winning heading. Discussion and conclusion The DME directive by way of a simple calculation took the countries personal Occupational Exposure Limit (OEL) of 2 mg/m3 and formulated a limit of 5 mg/m3 for EED sampling results. Simple extrapolation of the EED results indicates that personal exposure is exceeded more than two-fold and thus the limit of 5 mg/m3 as set by Directive B7 cannot be compared to the personal respirable coal dust OEL of 2 mg/m3. The basis of the initial calculation used to derive the 5 mg/m3 limit assumed that the shift lengths were in the region of 8 hours and cutting times around 40% of the shift, while most coal mines now have shift lengths ranging from 9 to 10 hours. In conclusion it is evident that the required limit of 5 mg/m3 as set out by Directive B7 cannot be related to the personal exposures limit of 2 mg/m3. Poor correlation results observed indicate that the EED sampling position does not account for the respirable dust concentrations leaving coal-winning headings and may be affected by the re-circulation of contaminated air over the sampling position. In addition the EED sampling position does not give an indication of the respirable dust capture efficiency of scrubber fans.

Thesis (Ph.D.)--Massachusetts Institute of Technology, Dept. of Economics, 1977. / MICROFICHE COPY AVAILABLE IN ARCHIVES AND DEWEY. / Bibliography: leaves 157-163. / by Leslie I. Boden. / Ph.D.

Tailgate stability within longwall coal mining is critical to longwall productivity and safety of mine personnel. A mechanistic model was developed and tested to explain observed high deformation tailgate behaviour characterised by lateral strata movement. Field investigations were conducted at three Australian longwall mines with an emphasis on the measurement of; horizontal strata movement about gateroads during longwall extraction, and the load/deformation characteristics of standing supports. 3D numerical modelling was used to simulate tailgate deformation, and interaction of various support types and design strategies. The sensitivity of strata and support behaviour to; variations in roof geology, strength of sliding interfaces, depth of cover, pre-mining horizontal stress magnitude and orientation, and strength and stiffness characteristics of standing supports was modelled. Laboratory investigations of a standing support product, the ???Can???, at reduced scale (one third) were conducted. The tests determined the loading mechanics of the product and provided a basis for optimisation of the engineering properties (strength and stiffness). Horizontal strata movement about longwall extraction was found to have a significant impact on strata behaviour at two of the three mines investigated. The term ???skew roof??? was coined to describe the deformation process. Essentially the roof strata was found to ???skew??? towards the approaching goaf. The key geotechnical factors found to control the skew roof mechanism were; magnitude and orientation of the pre-mining horizontal stress, presence of weak interfaces along which sliding could occur, and shear strength of the interfaces. Measurement of the nature and extent of skew roof deformation specific to each mine provided a sound engineering basis for support design. These included; the relative roles of long tendons versus standing support, optimal pattern (position across and along the roadway) of standing supports, and appropriate strength and stiffness characteristics. The findings were successfully implemented at Metropolitan Colliery in particular, where adequate tailgate serviceability has been achieved within a high deformation environment, and whilst maintaining a relatively small chain pillar width. The research has achieved an alternative to empirical and trial and error tailgate support design methods.

Thesis (M.S.)--West Virginia University, 2009. / Title from document title page. Document formatted into pages; contains xiii, 82 p. : ill. (some col.). Vita. Includes abstract. Includes bibliographical references (p. 65-66).

Thesis (Ph. D.)--West Virginia University, 2009. / Title from document title page. Document formatted into pages; contains xiii, 379 p. : ill. (some col.), maps (some col.). Vita. Includes abstract. Includes bibliographical references.