Spelling suggestions: "subject:"complementary splittring resonator"" "subject:"complementary splitring resonator""
1 |
Left-handed metamaterials realized by complementary split-ring resonators for RF and microwave circuit applicationsPasakawee, Sarinya January 2012 (has links)
A new equivalent circuit of left-handed (LH) microstrip transmission line loaded with Complementary split-ring resonators (CSRRs) is presented. By adding the magnetic coupling into the equivalent circuit, the new equivalent circuit presents a more accurate cutoff frequency than the old one. The group delay of CSRRs applied with microstrip transmission line (TL) is also studied and analyzed into two cases which are passive CSRRs delay line and active CSRRs delay line. In the first case, the CSRRs TL is analyzed. The group delay can be varied and controlled via signal frequency which does not happen in a normal TL. In the active CSRRs delay line, the CSRRs loaded with TL is fixed. The diodes are added to the model between the strip and CSRRs. By observing a specific frequency at 2.03GHz after bias DC voltages from -10V to -20V, the group delay can be moved from 0.6ns to 5.6ns. A novel microstrip filter is presented by embedding CSRRs on the ground plane of microstrip filter. The filter characteristic is changed from a 300MHz narrowband to a 1GHz wideband as well as suppression the occurrence of previous higher spurious frequency at 3.9GHz. Moreover, a high rejection in the lower band and a low insertion loss of <1dB are achieved.Finally, it is shown that CSRRs applied with planar antenna can reduce the antenna size. The structure is formed by etching CSRRs on the ground side of the patch antenna. The meander line part is also added on the antenna patch to tune the operation frequency from 1.8GHz downward to 1.73GHz which can reduce the antenna size to 74% of conventional patch antennas. By using the previous antenna structure without meander line, this proposed antenna can be tuned for selecting the operation frequency, by embedding a diode connected the position between patch and ground. The results provide 350MHz tuning range with 35MHz bandwidth.
|
2 |
Detection of Sub-Millimeter Surface Cracks using Complementary Split-Ring ResonatorAlbishi, Ali 13 July 2012 (has links)
Many interesting ideas have emerged from research on electromagnetic eld interactions
with di erent materials. Analyzing such interactions has extracted some essential proper-
ties of the materials. For example, extracting constitutive parameters such as permittivity,
permeability, and conductivity, clari es a material's behavior. In general, the electromag-
netic eld interacts with materials either in the far- eld or near- eld of a source. This
study focuses on the principle of near- eld microwave microscopy for detection purposes.
Many studies have focused on the use of an electrically small resonator, such as a
split-ring resonator (SRR) and a complementary split-ring resonator (CSRR), to act as a
near- eld sensor for material characterization and detection. At the resonance frequency,
the electric and magnetic energy densities are enhanced dramatically at certain locations
in the resonator. Any disturbance of the eld around such a resonator with a material
under test causes the resonance frequencies to exhibit a shift that is used as an indicator
of the sensor sensitivity. In this thesis, a single CSRR is used as a sensing element for
detecting cracks in metal surfaces.
Many microwave techniques have been developed for crack detection. However, these
techniques have at least one of the following drawbacks: working at high frequencies,
measurement setup complexity and cost, and low sensitivity. The rst part of this thesis
presents a new sensor based on the complementary split-ring resonator (CSRR) that is used
to detect sub-millimeter surface cracks. The sensing mechanism is based on perturbing the
electromagnetic eld around an electrically small resonator, thus initiating a shift in the
resonance frequency. Investigation of the current distribution on a CSRR at the resonance
frequency shows the critical location at which the enhanced energy is concentrated. In
addition, the current distribution demonstrates the sensing element in the CSRR. The
sensor is simple to fabricate and inexpensive, as it is etched-out in the ground plane of
a microstrip-line using printed circuit board technology. The microstrip-line excites the
CSRR by producing an electric eld perpendicular to the surface of the CSRR. The sensor
exhibits a frequency shift of more than 240 MHz for a 200 m crack.
In the second part of this thesis, the sensitivity of the sensor is increased by lling
the same crack with a dielectric material such as silicon oil. While using CSRR to scan a
block with 200 m wide and 2 mm depth dielectric lled crack, the resonance frequency
of the sensor shifts 435 MHz more than a case scanning a solid aluminum. Finally, the
total Inductance of a CSRR for miniaturizing purposes is increased using either lumped or
distributed elements. In this thesis, the designs and the results are validated experimentally
and numerically.
|
3 |
Detection of Sub-Millimeter Surface Cracks using Complementary Split-Ring ResonatorAlbishi, Ali 13 July 2012 (has links)
Many interesting ideas have emerged from research on electromagnetic eld interactions
with di erent materials. Analyzing such interactions has extracted some essential proper-
ties of the materials. For example, extracting constitutive parameters such as permittivity,
permeability, and conductivity, clari es a material's behavior. In general, the electromag-
netic eld interacts with materials either in the far- eld or near- eld of a source. This
study focuses on the principle of near- eld microwave microscopy for detection purposes.
Many studies have focused on the use of an electrically small resonator, such as a
split-ring resonator (SRR) and a complementary split-ring resonator (CSRR), to act as a
near- eld sensor for material characterization and detection. At the resonance frequency,
the electric and magnetic energy densities are enhanced dramatically at certain locations
in the resonator. Any disturbance of the eld around such a resonator with a material
under test causes the resonance frequencies to exhibit a shift that is used as an indicator
of the sensor sensitivity. In this thesis, a single CSRR is used as a sensing element for
detecting cracks in metal surfaces.
Many microwave techniques have been developed for crack detection. However, these
techniques have at least one of the following drawbacks: working at high frequencies,
measurement setup complexity and cost, and low sensitivity. The rst part of this thesis
presents a new sensor based on the complementary split-ring resonator (CSRR) that is used
to detect sub-millimeter surface cracks. The sensing mechanism is based on perturbing the
electromagnetic eld around an electrically small resonator, thus initiating a shift in the
resonance frequency. Investigation of the current distribution on a CSRR at the resonance
frequency shows the critical location at which the enhanced energy is concentrated. In
addition, the current distribution demonstrates the sensing element in the CSRR. The
sensor is simple to fabricate and inexpensive, as it is etched-out in the ground plane of
a microstrip-line using printed circuit board technology. The microstrip-line excites the
CSRR by producing an electric eld perpendicular to the surface of the CSRR. The sensor
exhibits a frequency shift of more than 240 MHz for a 200 m crack.
In the second part of this thesis, the sensitivity of the sensor is increased by lling
the same crack with a dielectric material such as silicon oil. While using CSRR to scan a
block with 200 m wide and 2 mm depth dielectric lled crack, the resonance frequency
of the sensor shifts 435 MHz more than a case scanning a solid aluminum. Finally, the
total Inductance of a CSRR for miniaturizing purposes is increased using either lumped or
distributed elements. In this thesis, the designs and the results are validated experimentally
and numerically.
|
Page generated in 0.1686 seconds