No

Yes / Steel-concrete composite structures are commonly used in buildings and bridges because it takes advantage of tensile strength of steel and compressive strength of concrete. The two components are often secured by shear connectors such as headed studs to prevent slippage and to maintain composite action. In spite of its popularity, very little research was conducted on steel-concrete composites particularly on headed stud shear connectors in regards to its post-fire behaviour. This research investigates the post-fire behaviour of innovative shear connectors for composite steel and concrete. Three type of connectors were investigated. They are headed stud shear connectors, Blind Bolt 1 and Blind Bolt 2 blind bolts. Push-out test experimental studies were conducted to look at the behaviour and failure modes for each connector. Eighteen push tests were conducted according to Eurocode 4. The push test specimens were tested under ambient temperatures and post fire condition of 200˚C, 400˚C and 600˚C. The results in ambient temperature are used to derive the residual strength of shear connectors after exposing to fire. Findings from this research will provide fundamental background in designing steel-concrete composites where there is danger of fire exposure.

No / In composite steel beams with precast hollow core slabs, the amount of transverse reinforcement can have a significant effect on the shear and slip capacity of the mechanical shear connectors. The issue of connector ductility becomes especially important when partial shear connection is adopted, as premature failure of the shear connectors would lead to sudden failure of the composite beam. This chapter presents its findings on the effect of transverse reinforcement on connector ductility and proposes design equations. Transverse reinforcement is used to provide ties for the slabs and confined concrete from splitting. The ductility of the shear connector, that is, slip capacity is directly affected by the amount of transverse reinforcement. Design equations presented in this chapter for estimating the shear capacity of the headed shear stud show a good correlation with the push-off test results. For full shear connection design, pre-splitting shear capacity of the headed stud can be used for the composite design, while for partial shear connection design, post-splitting shear capacity of the headed stud should be used. In general, a minimum transverse reinforcement of T16 bars should be used if partial shear connection design is used to ensure a minimum ductility of 6mm slip.

No

no / N/A

Over the last decade it has become increasingly clear that the traditional methods of fire safety design can be unnecessarily conservative and therefore expensive. In 1995 a series of fire tests were carried out at Cardington, UK on a full-scale eight storey steel-concrete composite building. These tests produced an extensive body of data about the response of such structures to fire conditions and it is intended that this data be used to develop a clearer understanding of the structural behaviour involved. This thesis presents a method of analysing the behaviour of structures such as the Cardington frame using the commercial finite element package ABAQUS, with the addition of user defined subroutines; applies the method to two of the Cardington tests and analyses the results. FEAST, a suite of computer programmes that defines the behaviour of shell finite elements using a stress-resultant approach, was programmed for use with ABAQUS. The FEAST suite consists of two main programmes. The first, SRAS, is designed to model the behaviour of orthotropic plate sections at elevated temperatures. The second, FEAI, interfaces with the finite element package ABAQUS and allows realistic models of the behaviour of whole structures in fire conditions to be obtained. Phenomena modelled by FEAST include non-linear thermal gradients, non-linear material behaviour and coupling between membrane and bending forces. FEAST was used to analyse the behaviour of the Cardington Restrained Beam Test and the Cardington Corner Test. In both cases it was possible to produce a comprehensive set of results showing the variation of forces, moments and deflections in the structure under fire conditions. In addition, a number of parametric studies were performed to determine the effect of factors such as slab temperature and coefficient of thermal expansion on the behaviour of the structure. Special attention was given to the role of tensile mebrane action. The results showed that the behaviour of the heated structure was very different to that of an unheated structure. The response of the structure was shown to be very strongly governed by restrained thermal expansion and by thermal gradients. Degradation of material properties were found to have only a secondary effect on the structural behaviour.

This thesis presents the results of a research study to investigate the behaviour of axially restrained composite beams at ambient and elevated temperatures, and how composite beams and their connections contribute to the robustness of composite framed structures in fire. The commercial finite element analysis package (ABAQUS, 2010) was used to develop the numerical simulation models. This research includes the following four main parts: (1) validation of the simulation model; (2) behaviour of axially restrained composite beams with partial shear interaction at ambient and elevated temperatures; (3) behaviour of composite beams with realistic connections at elevated temperatures and methods of increasing composite beam survival temperatures; and (4) response and robustness of composite frame structures with different extents of damage at elevated temperatures. Based on the results of composite beams, it was found that the survival of axially restrained beams is dominated by the development of catenary action. By utilising catenary action, it is possible for composite beams to develop load carrying capacity significantly above that based on bending resistance. During the development of catenary action, the compression force in the concrete flange of the composite beam decreases, thus reducing the forces in the shear connectors. As a result, the behaviour of shear connector failures ceases to be an issue during the catenary action stage. The results further show that, the load carrying capacities/survival temperatures of composite beams increase by increasing the level of axial restraint up to a certain limit and then decrease at higher levels. Typical realistic composite structures can provide composite beams with sufficient axial restraint to develop catenary action. For detailed composite beams with composite connections, three different beam sizes were investigated using flushed and extended end plate connections with different amounts of slab reinforcement, different load ratios and different bolt sizes. It has been found that the most important method to increase the survival time of composite beams is to use extended end plate connections with sufficient top and bottom reinforcement meshes in the concrete slab, i.e. increasing the amount of slab reinforcement is more beneficial than increasing the bolt size or the number of bolts. Based on the results of modelling a four bay (9 m each, two storey, 4 m high) composite frame with different extents of fire damage to different members, it was found that whenever any of the columns failed, progressive collapse of the frame would occur. Therefore, damages to columns should be prevented or the columns should be designed and constructed to allow for possible damage. If the beams are damaged, it is still possible for the damaged frame to achieve the reference fire resistance time of the undamaged structure (which is used as the criterion to accept that the damaged frame has sufficient robustness) by developing catenary action in the damaged beam. For this to happen, the columns should be designed to resist the catenary tensile force (tying force) in the beams, in addition to the compressive force.

This paper evaluates the effective width of composite steel beams with precast hollowcore slabs numerically using the finite element method. A parametric study, carried out on 27 beams with different steel cross sections, hollowcore unit depths and spans, is presented. The effective width of the slab is predicted for both the elastic and plastic ranges. 8-node three-dimensional solid elements are used to model the composite beam components. The material non-linearity of all the components is taken into consideration. The non-linear load-slip characteristics of the headed shear stud connectors are included in the analysis. The moment-deflection behaviour of the composite beams, the ultimate moment capacity and the modes of failure are also presented. Finally, the ultimate moment capacity of the beams evaluated using the present FE analysis was compared with the results calculated using the rigid – plastic method.

No

In steel¿concrete composite beams, the longitudinal shear force is transferred across the steel flange/concrete slab interface by the mechanical action of the shear connectors. The ability of the shear connectors to transfer these longitudinal shear forces depends on their strength, and also on the resistance of the concrete slab against longitudinal cracking induced by the high concentration of shear force. Most of the research in composite construction has concentrated on the more traditional reinforced concrete and metal deck construction, and little information is given on shear capacity of the headed studs in precast hollowcore slabs. In this paper, a standard push test procedure for use with composite beams with precast hollowcore slabs is proposed. Seven exploratory push tests were carried out on headed studs in solid RC slabs to validate the testing procedures, and the results showed that the new test is compatible with the results specified in the codes of practice for solid RC slabs. Once a standard procedure is established, 72 full-scale push tests on headed studs in hollowcore slabs were performed to determine the capacities of the headed stud connectors in precast hollowcore slabs and the results of the experimental study are analysed and findings on the effect of all the parameters on connectors¿ strength and ductility are presented. Newly proposed design equations for calculating the shear connectors¿ capacity for this form of composite construction are also be given.