The tensile resistance of No. 15 lap spliced reinforcing bars with varying transverse spacing and lap splice length was evaluated in full-scale concrete block wall splice specimens. The range of the transverse spacing between bars was limited to that which allowed the bars to remain within the same cell, and included the evaluation of tied spliced bars in contact. Two-and-a-half block wide by three course tall double pullout specimens reinforced with contact lap splices were initially used to determine the range of lap splice length values to be tested in the wall splice specimens such that bond failure of the reinforcement occurred. The double pullout specimens were tested in direct tension with six replicates per arrangement. Three values of lap splice length: 150, 200, and 250 mm, were selected from the testing of the double pullout specimens and tested in the wall splice specimens in combination with three values of transverse spacing: 0, 25, and 50 mm, with three replicates per configuration. A total of twenty-seven two-and-a-half block wide by thirteen course tall wall splice specimens reinforced with two lap splices were tested in four-point loading. Both the double pullout and the wall splice specimens were constructed in running bond with all cells fully grouted. The tensile resistance of the lap spliced bars in the double pullout specimens was measured directly. The contact lap splices with a 150, 200, and 250 mm lap splice length developed approximately 38, 35 and 29% of the theoretical yield load of the reinforcement, respectively. The difference between the mean tensile resistances of the three reinforcement configurations tested in the double pullout specimens was found to be statistically significant at the 95% confidence level. Different than expected, the tensile resistance of the lap spliced reinforcing bars in the double pullout specimens was inversely proportional to the lap splice length provided. For the short lap splice lengths used in this investigation, the linear but not proportional relationship between bond force and lap splice length known from reinforced concrete is believed to have caused this phenomenon. An iterative sectional analysis using moment-curvature response was used to calculate the tensile resistance of the lap spliced reinforcement in the wall splice specimens. The calculated mean tensile resistance of the reinforcement increased with increasing lap splice length, and was greater when the bars were in contact. Securing the bars in contact may have influenced the tensile capacity of the contact lap splices as higher stresses are likely to develop as a result of the bar ribs riding over each other with increasing slip. Results of the data analysis suggest that the tensile resistance of non-contact lap splices within the same cell is generally independent of the spacing between the bars. A comparison of the experimental results for the wall splice specimens with the development and splice length provisions in CSA S304.1-04 and TMS 402-11 indicate that both the Canadian and U.S. design standards are appropriate for both contact and non-contact lap splices located within the same cell given the limited test database included in this investigation.

<p>This thesis reports on shake table tests on fully-grouted reinforced masonry (RM) shear walls. The test walls covers a range of design parameters to facilitate benchmarking, a thorough performance investigation, and calibration of numerical models as well as development of fragility curves within the context of Performance Based Seismic Design (PBSD). The details of the experimental program undertaken, including general observations in terms of cracking patterns and failure modes of the tested walls and the results on the lateral strength, hysteretic response, dynamic properties, and the contribution of different displacement components to the response of the walls, are presented. More detailed analyses include seismic performance quantification of the walls in terms of inelastic behaviour characteristics, various energy components, and the effective dynamic properties of the tested walls. The analysis is concluded with development of simplified nonlinear response history analytical models and seismic fragility assessment tools for the tested walls. In general, the study results indicated that the displacement ductility capacity of the RM walls and their capability to dissipate energy through plastic hinging are higher than what is currently recognized by the National Building Code of Canada (NBCC). The fragility assessment study further indicated that similar walls are expected to conform to the current drift limits of the NBCC even at high seismic regions in Canada. The results of this study are expected to contribute to the growing Seismic Performance Database (SPD) of RM Seismic Force Resisting System (SFRS), and to the understanding of the lightly reinforced masonry wall system behaviour.</p> / Master of Applied Science (MASc)