Title: Study of electrical and dielectric properties of conducting polymers Author: Mgr. Martin Varga Department: Department of Macromolecular Physics Supervisor: RNDr. Jan Prokeš, CSc., Department of Macromolecular Physics Abstract: Charge transport in polyaniline (PANI) and polypyrrole (PPy) was studied in respect to various oxidants, dopants, morphology, and other modifica- tions in their synthesis. The mechanism of transport was discussed in the frame- work of combination of several models characteristic for disordered solids due to inherent heterogeneous structure of conducting polymers. Effect of drying on conductivity was studied and the long-time limit was explained with the diffusion- based model for bulk materials. For PPy nanotubes stability in strong alkaline media and aging were studied by AC and DC techniques. While conductivity of naturally aged samples after two years remained in the same order of magni- tude, after exposure to alkaline media or accelerated aging at high temperatures, conductivity decreased several orders of magnitude. Degraded material exhibited strong disorder and the transport model was completely changed. Despite severe treatment electrical properties were still comparable to other as-prepared mate- rials. Finally, an application example as ammonia sensor, the response of...

The main motivation in this thesis is to compare the conformation and charge transport in conducting polymers and carbon nanotubes (CNTs) and to investigate those physical properties in their combined form of nanocomposites. It is known that both conducting polymers and carbon nanotubes are intrinsically 1-dimensional systems which consist of delocalized π-electrons. However, the main difference between these is the fact that flexibility of conducting polymers can be varied depending on the extent of conjugation while CNTs are rigid. Hence a comparison of electronic properties as correlated to their morphology has been carried out and their individual role in nanocomposites is further studied. The thesis consists of 6 chapters and appendix. Chapter 1 consists of brief introduction of general properties of both conducting polymers, CNTs and their nanocomposites. Chapter 2 deals with the sample preparation and experimental techniques used for the work. Chapter 3 elaborates on the conformational / structural studies on the systems. Chapter 4 focuses on the transport measurements to study the electronic properties of the samples. Chapter 5 reveals the magnetic properties of these systems which can be applied in technological devices. And chapter 6 gives the conclusion and future directions of the work being done. Chapter 1: Nanocomposites represent a guest-host matrix consisting of easily processible functionalized conjugated polymer as host, incorporating carbon nanotubes as fillers with versatile electronic and magnetic properties, which provide a wide range of technological applications. The conformation, charge dynamics as well as magnetic properties of these conducting polymers and carbon nanotubes, and various aspects of transport mechanism and spin dynamics present in the nanocomposite matrix are studied and presented in a consistent framework. Chapter 2: The multiwall carbon nanotubes (MWNTs) are grown by thermal chemical vapor deposition (CVD). The MWNTs are dispersed in solution of conducting polymers by ultrasonication and then the suspension is cast on glass substrate and slowly dried by moderate heating. Once dried completely, the free-standing films of thickness 15-25 μm are peeled off the substrate for measurements. The MWNTs, above a certain concentration, form an interconnected network in the 3-dimensional polymer matrix, following percolation mechanism. The disorder is brought into the system mainly by bundling of tubes and bundle intersections. The morphology and conformation of the samples are studied by SEM, TEM and small angle X-ray scattering (SAXS) techniques. Chapter 3: Small angle X-ray scattering (SAXS) studies in polymeric systems are carried out to probe local nanoscale morphology at various length scales to show the correlation among conformation and assembly of chains. Small angle X-ray scattering (SAXS) studies are carried out in poly [2-methoxy5-(2’–ethyl-hexyloxy)-1,4-phenylene vinylene] (MEH-PPV) solution of varying conjugation lengths as well as different solvents. By increasing the extent of πconjugation from 30 to 100 %, the persistence length increases by a factor of three. Moreover, a pronounced second peak in the pair distribution function is observed in fully conjugated chain, at larger length scales which indicates that the chain segments tend to self-assemble as the conjugation along the chain increases. The chain assembly and aggregation are further studied for suspensions of MWNTs in polyethylene dioxythiophene-polystyrene (PEDOT-PSS) with aqueous medium and DMSO (dimethyl sulphoxide). The SAXS profile of MWNT dispersion in aqueous PEDOT-PSS clearly show rigid-rod feature of the individual nanotubes evident by the q-1 behavior at short ranges. The crossover from q-1 to q-2 in the longer range further suggest that the suspension consists of individual nanotubes, nanotubes bundles and aggregates that give rise to a 3-dimensonal meshwork of intersecting tubes and ropes. For the MWNT dispersion in PEDOT-PSS with DMSO, however, such q-1 behavior is absent; which evidently shows that the rods are not isolated in the solution and are rather agglomerated. How these conformations affect the electrical and magnetic properties of these systems are studied further in Chapter 4. Chapter 4: Transport mechanism in single wall carbon nanotubes (SWNT), MWNT pellets, and nanocomposite films of MWNT and PEDOT-PSS is studied. The positive and negative magnetoresistance (MR) data in various SWNT samples are analyzed by taking into account the electron-electron interaction (EEI) contribution, in addition to the weak localization (WL) regime. The contribution from EEI to the total MR is confirmed from the universal scaling of MC relation showing that EEI plays a significant role at higher fields and lower temperatures. Intrinsic parameters like inelastic scattering length extracted for barely metallic sample follows the T-3/4 dependence due to inelastic electron-electron scattering in the dirty limit. Conductivity and magnetoresistance (MR) measurements on nanocomposite films with varying MWNT content (0.03 - 3 %) are performed at a field range 0-11 Tesla, and temperature range 1.3–300 K. The temperature dependence of resistance above 4 K suggests a Coulomb-gap variable range hopping (CG-VRH) transport in the network. Alhough solely negative MR (~ 5-6 %) is observed for pristine MWNT pellets; the nanocomposite films show a combination of large negative MR (~ 80 %) at T < 4 K, and a comparatively weaker positive MR (~ 30 %) for T > 4 K. This suggest that there are two mechanism interplaying and dominant at different temperature regimes which can be explained by the mechanism of transport of the charge carriers of MWNT intervened by that of the polymer matrix. In conclusion how the individual properties of conducting polymer and carbon nanotubes contribute to the unique electronic and conformational properties in their nanocomposites is framed in this investigation. Chapter 5: Magnetic properties of the pristine MWNTs as well as metal nanowires of nickel, nickel-iron (NiFe), nickel-iron-cobalt (NiFeCo) encapsulated in the MWNTs are studied using superconducting quantum interference device (SQUID) magnetometer. A typical example of Ni nanowires encapsulated in MWNT (Ni-MWNT) is taken and the results are compared to other forms of nickel (bulk, nanorod cluster, nanowire) to see the effect of size, shape and environment on the magnetic kproperties. The saturation magnetization and coercivity for Ni-MWNTs are 1.0 emu/gm and 230 Oe. The temperature dependence of magnetization indicates superparamagnetic which is supported by the field-cooled and zero-field-cooled plots determining a blocking temperature ~ 300 K. These altered magnetic properties of Ni-MWNTs are mainly due to the contribution from carbon nanotube encapsulation. Both the shape and environment enhance the total magnetic anisotropy of encapsulated nanowires at least by a factor of four. The encapsulation of metal nanowires in MWNTs tunes the magnetic properties of the system widely, e.g. from diamagnetic (pristine MWNTs) to paramagnetic (Ni-MWNT) to ferromagnetic (NiFe-MWNT) and a combination of para and ferro (NiFeCo-MWNT). Chapter 6: The conclusions of the different works presented in the thesis are coherently summarized in this chapter. Thoughts for future directions are also summed up. Appendix A: Spin dynamics in conducting polymer PEDOT-PSS in its pristine, processed with DMSO and nanocomposite form (with carbon nanotubes) is studied using solid state nuclear magnetic resonance (NMR). Plots of proton spin lattice relaxation times vs. temperature at a fixed frequency 23.4 MHz are compared to study the effect of the external agents on the polymer dynamics.

Conducting and semiconducting polymers, consisting of delocalized π-electrons, have been studied for the past three decades. These materials have shown novel physical properties with interesting applications in batteries, detectors, light emitting diodes, field effect transistors, solar cells, biosensors etc. Nevertheless the charge transport properties are yet to be understood in detail due to the complexity of the system, especially due to the interplay of quasi-one dimensionality (q-1D), disorder, localization and electron-electron interactions(EEI). A combined investigation of both conductivity and spin lattice relaxation time, especially at very low temperatures and high magnetic fields, is really lacking in conducting polymers. In this thesis a set of experiments – dc conductivity, magnetoresistance (MR), Nuclear Magnetic Resonance (NMR) spin lattice relaxation time (T1) measurements, magnetic susceptibility amd ac conductivity have been carried out in conducting polymers. NMR being a local probe it is possible to get the nanoscopic scale charge transport mechanism. Further, this helps to develop a consistent understanding among a wide range of the physical properties in conducting polymers. In this thesis author has reported the results of experiments at ultra low temperature (mk) and ultra high magnetic field which give more insight about the roles of electron-electron interaction(EEI) and disorderin charge transport properties. This thesis describes a detailed study of charge transport and NMR relaxation in three representative conducting polymers namely polypyrrole(PPy)., poly-3-methylthiophene(P3MT) and poly3-hexylthiophene(P3HT). The emphasis is to understand the charge transport phenomena and NMR relaxation, especially at ultra low temperatures (down to 20 mk) and high magnetic field (up to 23.4 T). The NMR T1 relaxation mechanisms are discussed in terms of (i) Korringa relaxation, (ii) relaxation due to spin diffusion to paramagnetic centers (SDPC) amd (iii) reorientation of symmetric groups, depending upon the temperature range.

The Thesis reports charge transport studies on conducting polymers, polymer carbon nanotube composites and organic semiconductor devices. Conducting and semiconducting polymers consisting of π-conjugated chains have attracted considerable attention as they combine the optoelectronic properties of semiconductors with mechanical properties and processing advantages of plastics. The chemical/electrochemical/photodoping of these semiconducting polymers can tune the Fermi levels and conductivity in a controlled way, and hence the properties of devices can be easily tailored to suit in several applications. Carbon nanotube (CNT) is another another novel promising material for electronic/optoelectronic applications. Lately there has been a great interest in developing composites of polymer and CNTs to utilize the advantages of both CNTs and polymers. The inclusion of CNTs in polymers improves the mechanical, electrical and thermal properties since the aspect ratio (ratio of length to diameter) is very large, as well its density is rather low. The Thesis consists of 6 chapters. First chapter is a brief introduction of general and transport properties of conducting polymers and polymer-carbon nanotube composites. In Chapter 2, the sample preparation and experimental techniques used in this work are discussed. The charge transport in poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT-PSS) is presented in Chapter 3. Chapter 4 focuses on the transport measurements in the polymer-CNT composite samples. Chapter 5 elaborates the ac and dc characterization of organic field-effect transistors (OFETs). And chapter 6 presents the conclusion and future directions of the work that has been presented in the Thesis. Chapter 1: In the scientific and technological revolution of the last few years, the study of high performance materials has been steadily increasing including the study of carbon-based materials. Conducting polymers have special properties that are interesting for this new technology. The charge transport in conjugated polymers is important to optimize the performance of devices. The discovery of CNTs with exceptional thermal, mechanical, optical, electrical and structural properties has facilitated the synthesis of new type of nanocomposites with very interesting properties. Nanocomposites represent a guest-host matrix consisting of easily processible functionalized conjugated polymer as host, incorporating CNTs as fillers with versatile electronic and magnetic properties, which provide a wide range of technological applications. To optimize their electrical properties it is essential to understand the charge transport mechanism in detail. Chapter 2: The multi-wall carbon nanotubes (MWNTs) grown by thermal chemical vapor deposition (CVD) are mixed with a 1:1 mixture of 98% H2SO4 and 70% HNO3 to produce sulfonic acid functionalized multi-wall carbon nanotubes (s-MWNTs). The s-MWNTs are dispersed in a solution of Nafion by ultrasonication and then cast on a glass substrate and slowly dried by moderate heating to obtain the composite films. Polyaniline (PANI)-MWNT composites were obtained by carrying out the chemical synthesis of nanofibrilar PANI in the presence of CNTs. This water dispersible PANIMWNT composite contains well segregated MWNTs partially coated by nanofibrilar PANI. The ac and dc charge transport measurements suggest hopping transport in these materials. OFETs are fabricated with pentacene, poly(2,5-bis(3-tetradecylthiophen-2-yl)thieno[3,2-b]thiophene)(PBTTT) and poly(3-hexylthiophene) (P3HT) as active materials. A novel technique is used to characterize the acphotoresponse of these OFETs. Chapter 3: Charge transport studies on PEDOT-PSS have been carried out and found that it correlates with the morphology. The dc conductivity of PEDOT–PSS shows enhanced delocalization of the carriers upon the addition of dimethyl sulfoxide (DMSO) and this is attributed to the extended chain conformation. PEDOT-PSS is known to form a phase-segregated material comprising highly conducting PEDOT grains that are surrounded by a sea of weakly ionic-conducting PSS and a wide variation in the charge transport properties of PEDOT-PSS films is attributed to the degree of phasesegregation of the excess insulating polyanion. The magnetotransport and temperature dependent ac transport parameters across different conducting grades of PEDOT-PSS processed with DMSO were compared. Depending on the subtle alterations in morphology, the transport at low temperatures is shown to vary from the hopping regime (Baytron P) to critical regime of the metal-insulator transition (Baytron PH510) There is a significant positive magnetoresistance (MR) for P–films, but this is considerably less in case of PH510-film. From the low temperature ac conductance it is found that the onset frequency for PH510 is nearly temperature independent, whereas in P type it is strongly temperature dependent, again showing the superior transport in PH510. The presence of ‘shorter network connections’ together with a very weak temperature dependence down to ~ 5 K, suggest that the limitation on transport in PH510 arises from the connectivity within the PEDOT-rich grain rather than transport via the PSS barriers. Chapter 4: DC and AC charge transport properties of Nafion s-MWNT and PANI-MWNT composites are studied. Such a detailed investigation is required to optimize the correlation among morphology and transport properties in these composites towards applications in field-effect transistors, antistatic coating, electromagnetic shielding, etc. The conductivity in Nafion s-MWNT shows a percolative transport with percolation threshold pc = 0.42 whereas such a sharp percolation is absent in PANI-MWNT composite since the conduction via PANI matrix smears out the onset of rapid increase in conductivity. Three-dimensional variable range hopping (VRH) transport is observed in Nafion s-MWNT composites. The positive and negative MR data on 10 wt. % sample are analyzed by taking into account forward interference mechanism (negative MR) and wave-function shrinkage (positive MR), and the carrier scattering is observed to be in the weak limit. The electric-field dependence, measured to high fields, follows the predictions of hopping transport in high electric-field regime. The ac conductivity in 1 wt. % sample follows a power law: ( )  A s , and s decreases with increasing temperature as expected in the correlated barrier hopping (CBH) model. In general, Mott’s VRH transport is observed in PANI-MWNT samples. It is found that the MWNTs are sparingly adhered with PANI coatings, and this facilitates inter-tube hopping at low temperatures. The negative MR of MWNT-PANI composites suggest that the electronic transport at low temperatures is dominated by MWNT network. AC impedance measurements at low temperatures with different MWNT loading show that ac conductivity become temperature independent as the MWNT content increases. The onset frequency for the increase in conductivity is observed to be strongly dependent on the MWNT weight percentage, and the ac conductivity can be scaled onto a master curve given by  ( )  0[1 k( 0 )s ]. Chapter 5: Organic field-effect transistors (OFETs) based on small molecules and polymers have attracted considerable attention due to their unique advantages, such as low cost of fabrication, ease of processing and mechanical flexibility. Impedance characterization of these devices can identify the circuit elements present in addition to the source-drain (SD) channel, and the bottlenecks in charge transport can be identified. The charge carrier trapping at various interfaces and in the semiconductor can be estimated from the dc and ac impedance measurements under illumination. The equivalent circuit parameters for a pentacene OFET are determined from low frequency impedance measurements in the dark as well as under light illumination. The charge accumulation at organic semiconductor–metal interface and dielectric semiconductor interface is monitored from the response to light as an additional parameter to find out the contributions arising from photovoltaic and photoconductive effects. The shift in threshold voltage is due to the accumulation of photogenerated carriers under SD electrodes and at dielectric–semiconductor interface, and also this dominates the carrier transport. Similar charge trapping is observed in an OFET with PBTTT as the active material. This novel method can be used to differentiate the photophysical phenomena occurring in the bulk from that at the metal-semiconductor interface for the polymer. Chapter 6: The conclusions from the various works presented in the thesis are coherently summarized in this chapter. Thoughts for future directions are also summed up.