No description available.

Indiana University-Purdue University Indianapolis (IUPUI) / Proton exchange membrane fuel cells (PEMFC’s) offer an attractive alternative energy resource over traditional fossil fuels. The advantages such as high power density, relatively quick start-up, rapid response to varying loads and low operating temperatures make it a preferred technology option compared to other alternative energy sources. Nafion® by DuPont plays an integral role in the success of PEM fuel cells due to its high proton conductivity and high chemical and thermal stability. This research project aims to study the effect of mechanical and hygro-thermal stresses on the mechanical performance and proton conductivity of the membrane by subjecting it to realistic operating conditions such as those encountered in an automobile. In this thesis, the time-dependent behavior of the membrane has been modeled using a Prony series and the change in the conductivity due to mechanical loading was experimentally measured. The modeling of both electrochemical and mechanical properties can further be used in studying the degradation properties of the membrane and should guide the development of better membrane materials. Visco-elastic stress relaxation theory has been used in modeling the time-dependent behavior of the specimen. The EIS spectrum has been analyzed using a non-linear least squares method and an equivalent circuit method was also used to fit the spectra. This project was conducted in three phases. In the first phase a novel test facility was built to perform the experiments. A conductivity measurement test cell that measured the proton conductivity of a membrane was modeled and manufactured. The second phase included the design of different experiments that helped in modeling the interdependence of electrochemical and mechanical properties of the membrane. In this process, three series of experiments that tested the electrochemical and mechanical properties of the specimen were conducted. The membrane was held at constant strain and the through plane impedance was measured at different times during the test, specifically before and after stretching at ambient and varying environmental conditions. The membrane was also subjected to both mechanical and hygro-thermal loading conditions during the test. In the third phase, time-dependant mathematical model for the changes in the material properties were developed. The experimental apparatus thus tested the mechanical and electrochemical properties of the membrane simultaneously while the specimen was being subjected to constant mechanical and varying hygro-thermal conditions. Since the testing method is a novel procedure, the reliability and repeatability of the experimental facility has been verified before conducting the experiments. The experimental apparatus can further be used to test the membrane at varying strain rates and different hygro-thermal loading conditions in a consistent manner. The model developed can be used to analyze the degradation behavior of membrane and also to build better fabrication methods and membrane materials in future.

Thermal conductivity is an important thermophysical property needed for effectively predicting fuel performance. As part of the Next Generation Nuclear Plant (NGNP) program, the thermal conductivity of tri-isotropic (TRISO) fuel needs to be measured over a temperature range characteristic of its usage. The composite nature of TRISO fuel requires that measurement be performed over the entire length of the compact in a non-destructive manner. No existing measurement system is capable of performing such a measurement. A measurement system has been designed based on the steady-state, guarded-comparative-longitudinal heat flow technique. The system as currently designed is capable of measuring cylindrical samples with diameters ~12.3-mm (~0.5″) with lengths ~25-mm (~1″). The system is currently operable in a temperature range of 400 K to 1100 K for materials with thermal conductivities on the order of 10 W/m/K to 70 W/m/K. The system has been designed, built, and tested. An uncertainty analysis for the determinate errors of the system has been performed finding a result of 5.5%. Finite element modeling of the system measurement method has also been accomplished demonstrating optimal design, operating conditions, and associated bias error. Measurements have been performed on three calibration/validation materials: SS304, 99.95% pure iron, and inconel 625. In addition, NGNP graphite with ZrO2 particles and NGNP AGR-2 graphite matrix only, both in compact form, have been measured. Results from the SS304 sample show agreement of better than 3% for a 300–600°C temperature range. For iron between 100–600°C, the difference with published values is < 8% for all temperatures. The maximum difference from published data for inconel 625 is 5.8%, near 600°C. Both NGNP samples were measured from 100–800°C. All results are presented and discussed. Finally, a discussion of ongoing work is included as well as a brief discussion of implementation under other operating conditions, including higher temperatures and adaptation for use in a glovebox or hot cell.

Thermal conductivity is an important thermophysical property needed for effectively predicting nuclear fuel performance. As part of the Next Generation Nuclear Plant (NGNP) program, the thermal conductivity of tri-isotropic (TRISO) fuel needs to be measured over a temperature range characteristic of its usage. The composite nature of TRISO fuel requires that measurement be performed over the entire length of the compact in a non-destructive manner. No existing measurement system is capable of performing such a measurement. A measurement system has been designed based on the steady-state, guarded comparative-longitudinal heat flow technique. The system is capable of measuring cylindrical samples with diameters ∼12.3 mm (∼0.5 in.) with lengths ∼25 mm (∼1 in.). The system is currently operable in a temperature range of 100-700°C for materials with thermal conductivities on the order of 10-70 W*m-1*K-1. The system has been designed, built, and tested. An uncertainty analysis for the determinate errors of the system has been performed finding a result of 6%. Measurements have been performed on three calibration/validation materials: a certified glass ceramic reference material, 99.95% pure iron, and Inconel 625. The deviation of the validation samples is < 6-8% from the literature values. In addition, surrogate NGNP compacts and NGNP graphite matrix-only compacts have been measured. The results give an estimation of the thermal conductivity values that can be expected. All the results are presented and discussed. A Finite Element Analysis was done to compare the accuracy of multiple effective conductivity models. The study investigated the effects of packing structure, packing fraction, matrix thermal conductivity, and particle heat generation. The results show that the Maxwell and the Chiew & Glandt models provide the most accurate prediction of the effective thermal conductivity of the TRISO fuel compacts. Finally, a discussion of ongoing work is included as well as the possibility of correlating effective thermal properties of fuel compacts to their constituents with measurements of well-defined samples.

The purpose of this study was to evaluate the effectiveness of traditional hydrogeologic characterization approaches in a highly heterogeneous glaciofluvial aquifer at the North Campus Research Site (NCRS), situated on the University of Waterloo campus. Continuous soil cores to a depth of approximately 18 m were collected during the installation of the CMT monitoring wells and the multi-screen pumping well. K estimates were obtained for the core by obtaining 471 samples and testing them with a falling head permeameter, as well as by utilizing empirical equations developed to estimate K. A geostatistical analysis performed on the K datasets yielded strongly heterogeneous kriged K fields for the site. K and Ss were also estimated via type curve analysis of slug and pumping test data collected at the site. The various K and Ss estimates were then evaluated by simulating the transient drawdown data using a 3D forward numerical model constructed using Hydrogeosphere (Therrien et al., 2005). Results showed that, while drawdown predictions generally improved as more complexity was introduced into the model, the ability to make accurate drawdown predictions at all of the CMT ports was inconsistent. These results suggest that new techniques may be required to accurately capture subsurface heterogeneity for improved predictions of flow in similar systems.

The purpose of this study was to evaluate the effectiveness of traditional hydrogeologic characterization approaches in a highly heterogeneous glaciofluvial aquifer at the North Campus Research Site (NCRS), situated on the University of Waterloo campus. Continuous soil cores to a depth of approximately 18 m were collected during the installation of the CMT monitoring wells and the multi-screen pumping well. K estimates were obtained for the core by obtaining 471 samples and testing them with a falling head permeameter, as well as by utilizing empirical equations developed to estimate K. A geostatistical analysis performed on the K datasets yielded strongly heterogeneous kriged K fields for the site. K and Ss were also estimated via type curve analysis of slug and pumping test data collected at the site. The various K and Ss estimates were then evaluated by simulating the transient drawdown data using a 3D forward numerical model constructed using Hydrogeosphere (Therrien et al., 2005). Results showed that, while drawdown predictions generally improved as more complexity was introduced into the model, the ability to make accurate drawdown predictions at all of the CMT ports was inconsistent. These results suggest that new techniques may be required to accurately capture subsurface heterogeneity for improved predictions of flow in similar systems.

Temperature rise due to Joule heating of on-chip interconnects can severely affect performance and reliability of next generation microprocessors. Thermal predictions become difficult due to large number of features, and the impact of electron size effects on electrical and thermal transport. It is thus necessary to develop efficient numerical approaches, and accurate metal and dielectric thermal characterization techniques. In this research, analytical, numerical, and experimental techniques were developed to enable accurate and efficient predictions of interconnect temperature rise. A finite element based compact thermal model was developed to obtain temperature rise with fewer elements and acceptable accuracy. Temperature drop across the interconnect cross-section was ignored. The compact model performed better than standard finite element model in two and three-dimensional case studies, and the predictions for a real world structure agreed closely with experimentally measured temperature rise. A numerical solution was developed for electron transport based on the Boltzmann Transport Equation (BTE). This deterministic technique, based on the path integral solution of BTE within the relaxation time approximation, free electron model, and linear response, was applied to a constriction in a finite size thin metallic film. A correlation for effective conductance was obtained for different constriction sizes. The Atomic Force Microscope (AFM) based Scanning Joule Expansion Microscopy (SJEM) was used to develop a new technique to measure thermal conductivity of thin metallic films in the size effect regime. This technique does not require suspended metal structures, and thus preserves the original electron interface scattering characteristics. The thermal conductivities of 43 nm and 131 nm gold films were extracted to be 82 W/mK and 162 W/mK respectively. These measurements were close to Wiedemann-Franz Law predictions and are significantly smaller than the bulk value of 318 W/mK due to electron size effects. The technique can potentially be applied to interconnects in the sub-100 nm regime. A semi-analytical solution for the 3-omega method was derived to account for thermal conduction within the metallic heater. It is shown that significant errors can result when the previous solution is applied for anisotropic thermal conductivity measurements.

Este trabalho apresenta uma revisão de técnicas para medir propriedades térmicas de lmes, seguida de enfoque na termo-re etância transiente (TTR). Dentre as tecnologias existentes para medir propriedades térmicas, métodos ópticos são preferidos devido à sua natureza não-destrutiva, potencial de alta resolução temporal e espacial e calibração independente de contato físico. A implementação experimental deste método é apresentada, assim como a teoria da linha de transmissão utilizada para tratamento por Transformada de Laplace da equação de Fourier unidimensional do calor. Para facilitar o cálculo de invers ão desta Transformada, uma aproximação numérica, empregando o método Stehfest, foi usada. Experimentalmente, a evolução temporal da temperatura normalizada é mostrada para um lme de Au sobre Si e para lmes de Cu sobre substratos de vidro e Si, assim como foram utilizadas técnicas complementares de caracterização dos lmes (per lometria, elipsometria, microscopia de força atômica, eletrônica de varredura e de transmissão). Para o filme de ouro com espessura de 4:6µm, a teoria apresenta boa concordância com os resultados experimentais, já que o valor encontrado para a condutividade térmica do ouro está entre 230W/m.K e 280W/m.K, próximo e abaixo do valor da condutividade térmica do Au em volume (318W/m.K), indicando a validade do método implementado. Para lmes de cobre, porém, os resultados iniciais não apresentam a mesma concordância, e possíveis causas são discutidas. Futuramente, a TTR implementada poderá ser utilizada para determinação da condutividade térmica de lmes nos dielétricos ou semicondutores, e possivelmente na caracterização da componente transversal em filmes anisotrópicos. / This work presents a review of techniques to measure thermal properties off films, followed by a focused attention to the transient termo-re ectance (TTR). Amongst the existing technologies to measure thermal properties, optical methods are preferred due their nondestructive nature, high potential of spacial and temporal resolution, and independence from physical contact. The experimental implementation of this method is presented, as well as the theory of the transmission line theory used in the Laplace Transform treatment of the Fourier one-dimensional heat conduction equation. To facilitate the calculation of the Transform inversion, a numerical method, using the Stehfest method, was used. Experimentally, evolution of the normalized temperature is shown for a lm of Au on Si and for films of Cu on glass and Si substrates, whereas complementary techniques were used for film characterization (pro lometry, ellipsometry, atomic force microscopy, scanning and transmission eletron microscopy). For the Au film 4:6µm thick, the theory presents good agreement with the experimental results, and the value found for the thermal conductivity of the gold film is between 230W/m.K and 280W/m.K, near and below the bulk Au thermal conductivity (318W/m.K), indicating the validity of the method implementation. For Cu films, however, the initial results do not present the same agreement, and possible causes are discussed. In the future, the implemented TTR could be used for determination of the thermal conductivity of dielectric or semicondutors thin films, and possibly in the characterization of the transversal component in anisotropic films.

Este trabalho apresenta uma revisão de técnicas para medir propriedades térmicas de lmes, seguida de enfoque na termo-re etância transiente (TTR). Dentre as tecnologias existentes para medir propriedades térmicas, métodos ópticos são preferidos devido à sua natureza não-destrutiva, potencial de alta resolução temporal e espacial e calibração independente de contato físico. A implementação experimental deste método é apresentada, assim como a teoria da linha de transmissão utilizada para tratamento por Transformada de Laplace da equação de Fourier unidimensional do calor. Para facilitar o cálculo de invers ão desta Transformada, uma aproximação numérica, empregando o método Stehfest, foi usada. Experimentalmente, a evolução temporal da temperatura normalizada é mostrada para um lme de Au sobre Si e para lmes de Cu sobre substratos de vidro e Si, assim como foram utilizadas técnicas complementares de caracterização dos lmes (per lometria, elipsometria, microscopia de força atômica, eletrônica de varredura e de transmissão). Para o filme de ouro com espessura de 4:6µm, a teoria apresenta boa concordância com os resultados experimentais, já que o valor encontrado para a condutividade térmica do ouro está entre 230W/m.K e 280W/m.K, próximo e abaixo do valor da condutividade térmica do Au em volume (318W/m.K), indicando a validade do método implementado. Para lmes de cobre, porém, os resultados iniciais não apresentam a mesma concordância, e possíveis causas são discutidas. Futuramente, a TTR implementada poderá ser utilizada para determinação da condutividade térmica de lmes nos dielétricos ou semicondutores, e possivelmente na caracterização da componente transversal em filmes anisotrópicos. / This work presents a review of techniques to measure thermal properties off films, followed by a focused attention to the transient termo-re ectance (TTR). Amongst the existing technologies to measure thermal properties, optical methods are preferred due their nondestructive nature, high potential of spacial and temporal resolution, and independence from physical contact. The experimental implementation of this method is presented, as well as the theory of the transmission line theory used in the Laplace Transform treatment of the Fourier one-dimensional heat conduction equation. To facilitate the calculation of the Transform inversion, a numerical method, using the Stehfest method, was used. Experimentally, evolution of the normalized temperature is shown for a lm of Au on Si and for films of Cu on glass and Si substrates, whereas complementary techniques were used for film characterization (pro lometry, ellipsometry, atomic force microscopy, scanning and transmission eletron microscopy). For the Au film 4:6µm thick, the theory presents good agreement with the experimental results, and the value found for the thermal conductivity of the gold film is between 230W/m.K and 280W/m.K, near and below the bulk Au thermal conductivity (318W/m.K), indicating the validity of the method implementation. For Cu films, however, the initial results do not present the same agreement, and possible causes are discussed. In the future, the implemented TTR could be used for determination of the thermal conductivity of dielectric or semicondutors thin films, and possibly in the characterization of the transversal component in anisotropic films.

Este trabalho apresenta uma revisão de técnicas para medir propriedades térmicas de lmes, seguida de enfoque na termo-re etância transiente (TTR). Dentre as tecnologias existentes para medir propriedades térmicas, métodos ópticos são preferidos devido à sua natureza não-destrutiva, potencial de alta resolução temporal e espacial e calibração independente de contato físico. A implementação experimental deste método é apresentada, assim como a teoria da linha de transmissão utilizada para tratamento por Transformada de Laplace da equação de Fourier unidimensional do calor. Para facilitar o cálculo de invers ão desta Transformada, uma aproximação numérica, empregando o método Stehfest, foi usada. Experimentalmente, a evolução temporal da temperatura normalizada é mostrada para um lme de Au sobre Si e para lmes de Cu sobre substratos de vidro e Si, assim como foram utilizadas técnicas complementares de caracterização dos lmes (per lometria, elipsometria, microscopia de força atômica, eletrônica de varredura e de transmissão). Para o filme de ouro com espessura de 4:6µm, a teoria apresenta boa concordância com os resultados experimentais, já que o valor encontrado para a condutividade térmica do ouro está entre 230W/m.K e 280W/m.K, próximo e abaixo do valor da condutividade térmica do Au em volume (318W/m.K), indicando a validade do método implementado. Para lmes de cobre, porém, os resultados iniciais não apresentam a mesma concordância, e possíveis causas são discutidas. Futuramente, a TTR implementada poderá ser utilizada para determinação da condutividade térmica de lmes nos dielétricos ou semicondutores, e possivelmente na caracterização da componente transversal em filmes anisotrópicos. / This work presents a review of techniques to measure thermal properties off films, followed by a focused attention to the transient termo-re ectance (TTR). Amongst the existing technologies to measure thermal properties, optical methods are preferred due their nondestructive nature, high potential of spacial and temporal resolution, and independence from physical contact. The experimental implementation of this method is presented, as well as the theory of the transmission line theory used in the Laplace Transform treatment of the Fourier one-dimensional heat conduction equation. To facilitate the calculation of the Transform inversion, a numerical method, using the Stehfest method, was used. Experimentally, evolution of the normalized temperature is shown for a lm of Au on Si and for films of Cu on glass and Si substrates, whereas complementary techniques were used for film characterization (pro lometry, ellipsometry, atomic force microscopy, scanning and transmission eletron microscopy). For the Au film 4:6µm thick, the theory presents good agreement with the experimental results, and the value found for the thermal conductivity of the gold film is between 230W/m.K and 280W/m.K, near and below the bulk Au thermal conductivity (318W/m.K), indicating the validity of the method implementation. For Cu films, however, the initial results do not present the same agreement, and possible causes are discussed. In the future, the implemented TTR could be used for determination of the thermal conductivity of dielectric or semicondutors thin films, and possibly in the characterization of the transversal component in anisotropic films.