Spelling suggestions: "subject:"constitutive behaviour"" "subject:"constitutive ehaviour""
1 |
Application of a large deformation viscoelastic model to the unstable necking of polyethyleneSweeney, John, Coates, Philip D., Collins, T.L.D., Duckett, R.A. January 2002 (has links)
No / A large deformation, rate dependent model is applied to high temperature stretching of polyethylene. The theory is physically motivated, consisting of a model of a network of chain molecules to represent regions dominated by amorphous polymer, with embedded rigid spheres to introduce strain concentration similar to that caused by hard crystalline regions. Dependence on time and rate is introduced via shear stress driven diminution of the sphere radii. Experimentally, the rate dependence of the stress is such that, under tensile deformation, there is no necking associated with the initial yield point. Necking occurs at higher strains; this is associated with a weakening of rate dependence with increasing strain, which is a natural feature of the theory. It provides a realistic model of large tensile deformations, which in general involve the evolution of necking instabilities. It is implemented in a finite element scheme by using the package ABAQUS.
|
2 |
Hot tearing and constitutive behaviour of semi-solid aluminum alloysPhillion, Andre 05 1900 (has links)
The occurrence of hot tearing during solidification is one of the major factors influencing both the quality and productivity of aluminum castings. In order to reduce the formation of hot tears, quantitative information regarding both hot tearing formation and semi-solid deformation is essential.
In this study, the mechanisms of hot tearing and semi-solid deformation have been investigated via two novel techniques: x-ray micro-tomography on material deformed in the semi-solid region, and development of a three phase microstructural model based on a geometry derived from a Voronoi diagram with rounded corners and porosity. Numerical techniques were utilized to quantify both the size evolution and orientation of internal damage relative to void growth. In order to conduct the above research, a new semi-solid tensile deformation methodology was devised which uses a two thermocouple control technique to enable accurate measurement of semi-solid tensile strength and ductility. The experimental work was conducted on the aluminum – magnesium alloy AA5182 in the as-cast and hot isostatic pressing (HIP) states.
The x-ray micro-tomography technique was used to observe that semi-solid deformation is accommodated by internal damage via growth of as-cast porosity and the nucleation of new damage-based voids. As the volume fraction of damage increases, the growth of voids occurs in an orientation perpendicular to the loading direction, both through expansion within the grain boundary liquid and via coalescence between voids. The damage then localizes, causing failure.
The finite element semi-solid microstructural model was used to explore the effects of fraction solid, fraction porosity, and grain size on semi-solid constitutive behaviour. The simulations revealed that increased grain size and fraction porosity lead to a reduction in flow stress for a given fraction solid. Furthermore, local strain accumulation was linked to hot tearing, since strain localizes in the liquid very early in the deformation process. Based on the model predictions, a new constitutive relationship was developed over the range 0.75 < fs < 0.95.
Together, these two techniques have provided powerful new insight, such as the critical role played by as-cast porosity, on the phenomena of hot tearing and semi-solid deformation in aluminum alloys.
|
3 |
Hot tearing and constitutive behaviour of semi-solid aluminum alloysPhillion, Andre 05 1900 (has links)
The occurrence of hot tearing during solidification is one of the major factors influencing both the quality and productivity of aluminum castings. In order to reduce the formation of hot tears, quantitative information regarding both hot tearing formation and semi-solid deformation is essential.
In this study, the mechanisms of hot tearing and semi-solid deformation have been investigated via two novel techniques: x-ray micro-tomography on material deformed in the semi-solid region, and development of a three phase microstructural model based on a geometry derived from a Voronoi diagram with rounded corners and porosity. Numerical techniques were utilized to quantify both the size evolution and orientation of internal damage relative to void growth. In order to conduct the above research, a new semi-solid tensile deformation methodology was devised which uses a two thermocouple control technique to enable accurate measurement of semi-solid tensile strength and ductility. The experimental work was conducted on the aluminum – magnesium alloy AA5182 in the as-cast and hot isostatic pressing (HIP) states.
The x-ray micro-tomography technique was used to observe that semi-solid deformation is accommodated by internal damage via growth of as-cast porosity and the nucleation of new damage-based voids. As the volume fraction of damage increases, the growth of voids occurs in an orientation perpendicular to the loading direction, both through expansion within the grain boundary liquid and via coalescence between voids. The damage then localizes, causing failure.
The finite element semi-solid microstructural model was used to explore the effects of fraction solid, fraction porosity, and grain size on semi-solid constitutive behaviour. The simulations revealed that increased grain size and fraction porosity lead to a reduction in flow stress for a given fraction solid. Furthermore, local strain accumulation was linked to hot tearing, since strain localizes in the liquid very early in the deformation process. Based on the model predictions, a new constitutive relationship was developed over the range 0.75 < fs < 0.95.
Together, these two techniques have provided powerful new insight, such as the critical role played by as-cast porosity, on the phenomena of hot tearing and semi-solid deformation in aluminum alloys.
|
4 |
Hot tearing and constitutive behaviour of semi-solid aluminum alloysPhillion, André 05 1900 (has links)
The occurrence of hot tearing during solidification is one of the major factors influencing both the quality and productivity of aluminum castings. In order to reduce the formation of hot tears, quantitative information regarding both hot tearing formation and semi-solid deformation is essential.
In this study, the mechanisms of hot tearing and semi-solid deformation have been investigated via two novel techniques: x-ray micro-tomography on material deformed in the semi-solid region, and development of a three phase microstructural model based on a geometry derived from a Voronoi diagram with rounded corners and porosity. Numerical techniques were utilized to quantify both the size evolution and orientation of internal damage relative to void growth. In order to conduct the above research, a new semi-solid tensile deformation methodology was devised which uses a two thermocouple control technique to enable accurate measurement of semi-solid tensile strength and ductility. The experimental work was conducted on the aluminum – magnesium alloy AA5182 in the as-cast and hot isostatic pressing (HIP) states.
The x-ray micro-tomography technique was used to observe that semi-solid deformation is accommodated by internal damage via growth of as-cast porosity and the nucleation of new damage-based voids. As the volume fraction of damage increases, the growth of voids occurs in an orientation perpendicular to the loading direction, both through expansion within the grain boundary liquid and via coalescence between voids. The damage then localizes, causing failure.
The finite element semi-solid microstructural model was used to explore the effects of fraction solid, fraction porosity, and grain size on semi-solid constitutive behaviour. The simulations revealed that increased grain size and fraction porosity lead to a reduction in flow stress for a given fraction solid. Furthermore, local strain accumulation was linked to hot tearing, since strain localizes in the liquid very early in the deformation process. Based on the model predictions, a new constitutive relationship was developed over the range 0.75 < fs < 0.95.
Together, these two techniques have provided powerful new insight, such as the critical role played by as-cast porosity, on the phenomena of hot tearing and semi-solid deformation in aluminum alloys. / Applied Science, Faculty of / Materials Engineering, Department of / Graduate
|
5 |
Numerical and artificial neural network modelling of friction stir weldingWang, Hua January 2011 (has links)
This thesis is based on the PhD work of investigating the Friction Stir Welding process (FSW) with numerical and Artificial Neural Network (ANN) modelling methods. FSW was developed at TWI in 1991. As a relatively new technology it has great advantages in welding aluminium alloys which are difficult to weld with traditional welding processes. The aim of this thesis was the development of new modelling techniques to predict the thermal and deformation behaviour. To achieve this aim, a group of Gleeble experiments was conducted on 6082 and 7449 aluminium alloys, to investigate the material constitutive behaviour under high strainrate, near solidus conditions, which are similar to what the material experiences during the FSW process. By numerically processing the experimental data, new material constitutive constants were found for both alloys and used for the subsequent FSW modelling work. Importantly no significant softening was observed prior to the solidus temperature. One of the main problems with numerical modelling is determining the values of adjustable parameters in the model. Two common adjustable parameters are the heat input and the coefficients that describe the heat loss to the backing bar. To predict these coefficients more efficiently a hybrid model was created which involved linking a conventional numerical model to an ANN model. The ANN was trained using data from the numerical model. Then thermal profiles were abstracted (summarised) and used as inputs; and the adjustable parameters were used as outputs. The trained ANN could then use abstracted thermal profiles from welding experiments to predict the adjustable parameters in the model. The first stage involved developing a simplified FE thermal model which represents a typical welding process. It was used to find the coefficients that describe the heat loss to the backing bar, and the amount of power applied in the model. Five different thermal boundary conditions were studied, including both convective and ones that included the backing bar with a contact gap conductance. Three approaches for abstracting the thermal curves and using as inputs to the ANN were compared. In the study, the characteristics of the ANN model, such as the ANN topology and gradient descent method, were evaluated for each boundary condition for understanding of their influences to the prediction. The outcomes of the study showed that the hybrid model technique was able to determine the adjustable parameters in the model effectively, although the accuracy depended on several factors. One of the most significant effects was the complexity of the boundary condition. While a single factor boundary condition (e.g. constant convective heat loss) could be predicted easily, the boundary condition with two factors proved more difficult. The method for inputting the data into the ANN had a significant effect on the hybrid model performance. A small number of inputs could be used for the single factor boundary condition, while two factors boundary conditions needed more inputs. The influences from the characteristics of the ANN model were smaller, but again thermal model with simpler boundary condition required a less complex ANN model to achieve an accurate prediction, while models with more complex boundary conditions would need a more sophisticated ANN model. In the next chapter, the hybrid method was applied to a FSW process model developed for the Flexi-stir FSW machine. This machine has been used to analyse the complex phase changes that occur during FSW with synchrotron radiation. This unique machine had a complex backing bar system involving heat transfer from the aluminium alloy workpiece to the copper and steel backing bars. A temperature dependent contact gap conductance which also depends on the material interface type was used. During the investigation, the ANN model topologies (i.e. GFF and MFF) were studied to find the most effective one. Different abstracting methods for the thermal curves were also compared to explore which factors (e.g. the peak temperature in the curve, cooling slope of a curve) were more important to be used as an input. According to close matching between the simulation and experimental thermal profiles, the hybrid model can predict both the power and thermal boundary condition between the workpiece and backing bar. The hybrid model was applied to six different travel speeds, hence six sets of heat input and boundary condition factors were found. A universal set was calculated from the six outcomes and a link was discovered between the accuracy of the temperature predictions and the plunge depth for the welds. Finally a model with a slip contact condition between the tool and workpiece was used to investigate how the material flow behaviour was affected by the slip boundary condition. This work involved aluminium alloys 6082-T6 and 7449-T7, which have very different mechanical properties. The application of slip boundary condition was found to significantly reduce the strain-rate, compared to a stick condition. The slip condition was applied to the Flexi-stir FSW experiments, and the results indicated that a larger deformation region may form with the slip boundary condition. The thesis successfully demonstrates a new methodology for determining the adjustable parameters in a process model; improved understanding of the effect of slip boundary conditions on the flow behaviour during FSW and insight in to the behaviour of aluminium alloys at temperatures approaching the solidus and high strain-rates.
|
6 |
Numerical behaviour of buried flexible pipes in geogrid-reinforced soil under cyclic loadingElshesheny, Ahmed, Mohamed, Mostafa H.A., Nagy, N.M., Sheehan, Therese 23 March 2021 (has links)
Yes / Three-dimensional finite element models were executed and validated to investigate the performance of buried flexible high-density Polyethylene (HDPE) pipes, in unreinforced and multi-geogrid-reinforced sand beds, while varying pipe burial depth, number of geogrid-layers, and magnitude of applied cyclic loading. Geogrid-layers were simulated considering their geometrical thickness and apertures, where an elasto-plastic constitutive model represented its behaviour. Soil-geogrid load transfer mechanisms due to interlocked soil in-between the apertures of the geogrid-layer were modelled. In unreinforced and reinforced cases, pipe burial depth increase contributed to decreasing deformations of the footing and pipe, and the crown pressure until reaching an optimum value of pipe burial depth. On the contrary, the geogrid-layers strain increased with increasing pipe burial depth. A flexible slab was formed due to the inclusion of two-geogrid-layers, leading to an increase in the strain in the lower geogrid-layer, despite its lower deformation. Inclusion of more than two geogrid-layers formed a heavily reinforced system of higher stiffness, and consequently, strain distribution in the geogrid-layers varied, where the upper layer experienced the maximum strain. In heavily reinforced systems, increasing the amplitude of cyclic loading resulted in a strain redistribution process in the reinforced zone, where the second layer experienced the maximum strain.
|
7 |
Modelling and simulation of plastic deformation on small scales : interface conditions and size effects of thin filmsFredriksson, Per January 2008 (has links)
Contrary to elastic deformation, plastic deformation of crystalline materials, such as metals, is size-dependent. Most commonly, this phenomenon is present but unnoticed, such as the effect of microstructural length scales. The grain size in metallic materials is a length scale that affects material parameters such as yield stress and hardening moduli. In addition, several experiments performed in recent years on specimens with geometrical dimensions on the micron scale have shown that these dimensions also influence the mechanical behaviour. The work presented in this thesis involves continuum modelling and simulation of size-dependent plastic deformation, with emphasis on thin films and the formulation of interface conditions. A recently published strain gradient plasticity framework for isotropic materials [Gudmundson, P., 2004. A unified treatment of strain gradient plasticity. Journal of the Mechanics and Physics of Solids 52, 1379-1406] is used as a basis for the work. The theory is higher-order in the sense that additional boundary conditions are required and, as a consequence, higher-order stresses appear in the theory. For dimensional consistency, length scale parameters enter the theory, which is not the case for conventional plasticity theory. In Paper A and B, interface conditions are formulated in terms of a surface energy. The surface energy is assumed to depend on the plastic strain state at the interface and different functional forms are investigated. Numerical results are generated with the finite element method and it is found that this type of interface condition can capture the boundary layers that develop at the substrate interface in thin films. Size-effects are captured in the hardening behaviour as well as the yield strength. In addition, it is shown that there is an equivalence between a surface energy varying linearly in plastic strain and a viscoplastic interface law for monotonous loading. In paper C, a framework of finite element equations is formulated, of which a plane strain version is implemented in a commercial finite element program. Results are presented for an idealized problem of a metal matrix composite and several element types are examined numerically. In paper D, the implementation is used in a numerical study of wedge indentation of a thin film on an elastic substrate. Several trends that have been observed experimentally are captured in the theoretical predictions. Increased hardness at shallow depths due to gradient effects as well as increased hardness at more significant depths due to the presence of the substrate are found. It is shown that the hardening behaviour of the film has a large impact on the substrate effect and that either pile-up or sink-in deformation modes may be obtained depending on the material length scale parameter. Finally, it is qualitatively demonstrated that the substrate compliance has a significant effect on the calculated hardness of the film. / QC 20100723
|
8 |
Influence of different mechanisms on the constitutive behaviour of textile reinforced concreteHartig, Jens, Jesse, Frank, Häußler-Combe, Ulrich 03 June 2009 (has links) (PDF)
Textile Reinforced Concrete shows a complex load-bearing behaviour, which depends on material properties of the composite constituents and load transfer mechanisms in between. These properties cannot be modified arbitrarily in experimental investigations, which complicates identification of the impact of certain mechanisms on composite’s behaviour. In this respect, theoretical investigations offer the possibility to study the influence of individual parameters. At first, experimental results of tensile-loaded specimens are given, which help to identify different mechanisms in advance. Afterwards, respective results of numerical calculations with a reduced two-dimensional model are presented to study these mechanisms, including the effects of a reduced stiffness in the cracked state, yarn waviness and tension softening of the cementitious matrix.
|
9 |
Influence of different mechanisms on the constitutive behaviour of textile reinforced concreteHartig, Jens, Jesse, Frank, Häußler-Combe, Ulrich 03 June 2009 (has links)
Textile Reinforced Concrete shows a complex load-bearing behaviour, which depends on material properties of the composite constituents and load transfer mechanisms in between. These properties cannot be modified arbitrarily in experimental investigations, which complicates identification of the impact of certain mechanisms on composite’s behaviour. In this respect, theoretical investigations offer the possibility to study the influence of individual parameters. At first, experimental results of tensile-loaded specimens are given, which help to identify different mechanisms in advance. Afterwards, respective results of numerical calculations with a reduced two-dimensional model are presented to study these mechanisms, including the effects of a reduced stiffness in the cracked state, yarn waviness and tension softening of the cementitious matrix.
|
Page generated in 0.0789 seconds