This thesis examined the effect of differences in body surface area-to-lean body mass ratio (AD/LBM) on core temperature cooling rates during cold water immersion (2°C, CWI) and temperate water immersion (26°C, TWI) following exercise-induced hyperthermia (end-exercise rectal temperature of 40°C). Individuals with a High AD/LBM (315 cm2/kg) had a ~1.7-fold greater overall rectal cooling rate relative to those with Low AD/LBM (275 cm2/kg) during both CWI and TWI. Further, overall rectal cooling rates during CWI were ~2.7-fold greater than during TWI for both the High and Low AD/LBM groups. Study findings show that AD/LBM must be considered when determining the duration of the immersion period. However, CWI provides the most effective cooling treatment for EHS patients irrespective of physical differences between individuals.

The thesis work consists of two parts. First, the development of two-dimensional numerical models of a Bridgman unidirectional solidification furnace, and second, the construction work of the furnace at KTH. The aim is to build a Bridgman furnace which is capable of close control over temperature gradient and growth rate such that the solidification structures of a duplex stainless steel (SAF2507) could be replicated at a laboratory scale for different cooling rates.Two numerical models of Bridgman furnace are created using COMSOL Multiphysics. The models are used as predictive tools to simulate the locations of solidification front and the temperature gradients at the solidification fronts, which are parameters difficult to access during experiments. Different hot zone temperatures of the furnace (1500~1550 °C) and different sample pulling rates (0.5~10 mm/s) are studied in simulations. The major finding from modeled results is that the temperature gradient of the sample at the solidification fronts range from 5 ~ 17 K/mm, which are lower than the furnace temperature gradient of ~50 K/mm. The corresponding steady-state cooling rates range between 5 ~ 85 K/s. The next step is to validate the models with experimental temperature profiles of the furnace, and decide whether the furnace design should be modified to achieve the cooling rates of interests. / Examensarbetet består av två delar. Först utvecklingen av tvådimensionella numeriska modeller av en Bridgman enkelriktad stelningsugn, och för det andra konstruktionsarbetet för ugnen vid KTH. Syftet är att bygga en Bridgman-ugn som har förmåga att kontrollera temperaturgradienten och tillväxthastigheten så att stelningsstrukturerna i ett duplex-rostfritt stål (SAF2507) skulle kunna replikeras i laboratorieskala för olika kylningshastigheter. Två numeriska modeller av Bridgman-ugnen skapas med COMSOL Multiphysics. Modellerna används som prediktiva verktyg för att simulera placeringen av stelningsfronten och temperaturgradienterna vid stelningsfronterna, vilket är parametrar som är svåra att komma åt under experiment. Olika varmzonstemperaturer i ugnen (1500~1550 °C) och olika provdragningshastigheter (0.5~10 mm/s) studeras i simuleringar. Det viktigaste fyndet från modellerade resultat är att provets temperaturgradient vid stelningsfronterna sträcker sig från 5 ~17 K/mm, vilket är lägre än ugns temperaturgradient på ~ 50 K/mm. Motsvarande stabilitetskylningshastigheter varierar mellan 5 ~ 85 K/s. Nästa steg är att validera modellerna med experimentella temperaturprofiler för ugnen och bestämma om ugnsutformningen ska modifieras för att uppnå intressens kylningshastigheter.

No description available.

A técnica da Distribuição do Tamanho de Cristais - DTC (Crystal Size Distribution - CSD), que relaciona a densidade de cristais com a distribuição do tamanho, foi aplicada à população de plagioclásio de diques máficos do Enxame de Cabo Frio - Búzios (RJ). Os diques possuem larguras variáveis, de alguns centímetros a 20 metros, e orientação em torno de N45E. A textura dos diques é geralmente fina, localmente microporfirítica e intergranular no centro dos diques mais largos. Bordas resfriadas de alguns centímetros de largura são frequentes nos contatos com as rochas metamórficas encaixantes. Foram estudados dois diques na Praia das Conchas com espessura de 0,8m e 8,2m e, um outro na Praia da Lagoinha, com 2m de largura. As amostras foram coletadas junto às margens (~10 cm do contato) e no centro dos diques. O tamanho médio dos cristais de plagioclásio varia de 0,07 a 0,13 mm na borda dos diques mais finos (<= 2 m de largura) e de 0,09 a 0,20 mm na borda do dique mais largo. No centro do dique de Lagoinha e no dique largo de Praia das Conchas o tamanho de plagioclásio é da ordem de 0,19 ± 0,02 mm e 0,60 ± 0,07 mm, respectivamente. As DTCs nas bordas dos diques, independentemente de sua largura, mostraram um padrão tipicamente encurvado, e que tem sido atribuído na literatura como evidência para misturas de magmas com populações de cristais de tamanhos distintos. No entanto, no centro do dique largo (8,2m) de Praia das Conchas, a DTC é log-linear consistente com uma cristalização magmática simples. A química mineral mostrou que os cristais maiores (precoces) de plagioclásio apresentam um teor mais elevado em An (bytownita-labradorita) que os cristais menores (tardios) da matriz (labradorita-andesina). Além disso, a olivina é mais rica em Fo na borda que no centro do dique e, respectivamente, o piroxênio mais enriquecido em Ca. Esses resultados indicam que as margens resfriadas são mais máficas que o centro sugerindo uma evolução química normal com o resfriamento do magma. Portanto, as DTCs encurvadas provavelmente refletem taxas de cristalização heterogêneas possivelmente induzidas pela despressurização durante a ascensão do magma basáltico seguida de rápido resfriamento. O padrão da DTC log-linear no centro do dique de 8,2m de largura é atribuído ao maior tempo de residência do magma que favoreceria os processos de difusão química e re-equilíbrio textural. Os cálculos da taxa de resfriamento utilizando a inclinação da DTC permitiram estimar que o centro do dique largo da Praia das Conchas estaria completamente cristalizado (~ 900 °C) em torno de 73 dias. O estudo da Orientação Preferencial de Forma (OPF) de plagioclásio mostrou que a petrotrama tende a isotrópica nas margens dos diques com largura menor que 2 metros, o que poderia refletir uma rápida cristalização de plagioclásio por despressurização. Quando a trama é localmente definida, como no dique largo da Praia das Conchas, a lineação de plagioclásio é subhorizontal sugerindo que o fluxo magmático moveu-se predominantemente na lateral do dique. / The method of Crystal Size Distribution (CSD), which relates crystal density with size distribution, has been applied on the plagioclase population of the Mafic Dyke Swarm of Cabo Frio-Búzios (RJ). The dykes are NE-trending with widths from a few centimetres to 20m. The texture is generally fine grained and locally microporphyritic and intergranular at the center of the larger dykes. Chilled margins of a few centimetres in width are common at contacts with the metamorphic basement. Two dykes of 0.8m and 8.2m in width of the Conchas Beach and another of 2m in width at the Lagoinha Beach have been studied. Samples were collected at the margins (~10cm from the contact) and at the center of the dykes. The average characteristic size of the plagioclase crystals varies from 0.07 to 0.13mm at the margins of the narrow dykes (<=2m of width) and from 0.09 to 0.20mm at the margins of the large dyke. At the center of the Lagoinha and Conchas dykes the plagioclase size varies from 0.19 ±0.02mm and 0.60±0.07mm respectively. The CSDs at the dyke margins, irrespective of the dyke width, are typically concave-up, and in literature such patterns have been attributed as evidence of magma mixing with distinct crystal populations. However, at the center of the largest dyke (8.2m) of Conchas Beach, the CSD is log-linear, consistent with simple steady-state crystallization pattern. The mineral chemistry shows that the plagioclase phenocrysts have a high An content (bytownite-labradorite) than the groundmass grains (labradorite-andesine). At the margins olivine is richer in Fo than at the center, and respectively, pyroxene is richer in Ca. These results indicate that the chilled margin is more mafic than the center suggesting a normal chemical evolution in a cooling magma. Nevertheless, the concave-up CSDs probably depict heterogeneous crystallization rates possibly induced by depressurization during the ascent of the basaltic magma followed by rapid cooling. The log-linear CSD pattern at the center of the Conchas dyke (8.2m width) is attributed to a higher residence time of the magma which favors the processes of chemical diffusion and textural re-equilibration. The calculated cooling rates using the CSD slope enables us to estimate that the larger dyke of Conchas would be completely crystallized (at ~900oC) in 73 days. The study of the Shape Preferred Orientation (SPO) in plagioclase shows an isotropic petrofabric at the margins of the dykes <=2m, which could reflect a rapid crystallization of plagioclase by depressurization. When the fabric is defined, as in the larger Conchas Beach dyke, the plagioclase lineation is subhorizontal, suggesting that the magma flow was predominantly lateral to the dyke plane.

A técnica da Distribuição do Tamanho de Cristais - DTC (Crystal Size Distribution - CSD), que relaciona a densidade de cristais com a distribuição do tamanho, foi aplicada à população de plagioclásio de diques máficos do Enxame de Cabo Frio - Búzios (RJ). Os diques possuem larguras variáveis, de alguns centímetros a 20 metros, e orientação em torno de N45E. A textura dos diques é geralmente fina, localmente microporfirítica e intergranular no centro dos diques mais largos. Bordas resfriadas de alguns centímetros de largura são frequentes nos contatos com as rochas metamórficas encaixantes. Foram estudados dois diques na Praia das Conchas com espessura de 0,8m e 8,2m e, um outro na Praia da Lagoinha, com 2m de largura. As amostras foram coletadas junto às margens (~10 cm do contato) e no centro dos diques. O tamanho médio dos cristais de plagioclásio varia de 0,07 a 0,13 mm na borda dos diques mais finos (<= 2 m de largura) e de 0,09 a 0,20 mm na borda do dique mais largo. No centro do dique de Lagoinha e no dique largo de Praia das Conchas o tamanho de plagioclásio é da ordem de 0,19 ± 0,02 mm e 0,60 ± 0,07 mm, respectivamente. As DTCs nas bordas dos diques, independentemente de sua largura, mostraram um padrão tipicamente encurvado, e que tem sido atribuído na literatura como evidência para misturas de magmas com populações de cristais de tamanhos distintos. No entanto, no centro do dique largo (8,2m) de Praia das Conchas, a DTC é log-linear consistente com uma cristalização magmática simples. A química mineral mostrou que os cristais maiores (precoces) de plagioclásio apresentam um teor mais elevado em An (bytownita-labradorita) que os cristais menores (tardios) da matriz (labradorita-andesina). Além disso, a olivina é mais rica em Fo na borda que no centro do dique e, respectivamente, o piroxênio mais enriquecido em Ca. Esses resultados indicam que as margens resfriadas são mais máficas que o centro sugerindo uma evolução química normal com o resfriamento do magma. Portanto, as DTCs encurvadas provavelmente refletem taxas de cristalização heterogêneas possivelmente induzidas pela despressurização durante a ascensão do magma basáltico seguida de rápido resfriamento. O padrão da DTC log-linear no centro do dique de 8,2m de largura é atribuído ao maior tempo de residência do magma que favoreceria os processos de difusão química e re-equilíbrio textural. Os cálculos da taxa de resfriamento utilizando a inclinação da DTC permitiram estimar que o centro do dique largo da Praia das Conchas estaria completamente cristalizado (~ 900 °C) em torno de 73 dias. O estudo da Orientação Preferencial de Forma (OPF) de plagioclásio mostrou que a petrotrama tende a isotrópica nas margens dos diques com largura menor que 2 metros, o que poderia refletir uma rápida cristalização de plagioclásio por despressurização. Quando a trama é localmente definida, como no dique largo da Praia das Conchas, a lineação de plagioclásio é subhorizontal sugerindo que o fluxo magmático moveu-se predominantemente na lateral do dique. / The method of Crystal Size Distribution (CSD), which relates crystal density with size distribution, has been applied on the plagioclase population of the Mafic Dyke Swarm of Cabo Frio-Búzios (RJ). The dykes are NE-trending with widths from a few centimetres to 20m. The texture is generally fine grained and locally microporphyritic and intergranular at the center of the larger dykes. Chilled margins of a few centimetres in width are common at contacts with the metamorphic basement. Two dykes of 0.8m and 8.2m in width of the Conchas Beach and another of 2m in width at the Lagoinha Beach have been studied. Samples were collected at the margins (~10cm from the contact) and at the center of the dykes. The average characteristic size of the plagioclase crystals varies from 0.07 to 0.13mm at the margins of the narrow dykes (<=2m of width) and from 0.09 to 0.20mm at the margins of the large dyke. At the center of the Lagoinha and Conchas dykes the plagioclase size varies from 0.19 ±0.02mm and 0.60±0.07mm respectively. The CSDs at the dyke margins, irrespective of the dyke width, are typically concave-up, and in literature such patterns have been attributed as evidence of magma mixing with distinct crystal populations. However, at the center of the largest dyke (8.2m) of Conchas Beach, the CSD is log-linear, consistent with simple steady-state crystallization pattern. The mineral chemistry shows that the plagioclase phenocrysts have a high An content (bytownite-labradorite) than the groundmass grains (labradorite-andesine). At the margins olivine is richer in Fo than at the center, and respectively, pyroxene is richer in Ca. These results indicate that the chilled margin is more mafic than the center suggesting a normal chemical evolution in a cooling magma. Nevertheless, the concave-up CSDs probably depict heterogeneous crystallization rates possibly induced by depressurization during the ascent of the basaltic magma followed by rapid cooling. The log-linear CSD pattern at the center of the Conchas dyke (8.2m width) is attributed to a higher residence time of the magma which favors the processes of chemical diffusion and textural re-equilibration. The calculated cooling rates using the CSD slope enables us to estimate that the larger dyke of Conchas would be completely crystallized (at ~900oC) in 73 days. The study of the Shape Preferred Orientation (SPO) in plagioclase shows an isotropic petrofabric at the margins of the dykes <=2m, which could reflect a rapid crystallization of plagioclase by depressurization. When the fabric is defined, as in the larger Conchas Beach dyke, the plagioclase lineation is subhorizontal, suggesting that the magma flow was predominantly lateral to the dyke plane.

In s industrial production is more and more requierement to a saving costs. Findig savings has been removed even to the areas using safety parts, f.e. parts of car chassis. This projekct agglomerate posibilities of technology controled cooling proces of die forgings from micro alloy steel, which is right example how we can spare production expenditure. Micro alloy steel 30MNVS6 was studied within the standard production conditions. A lot of tests were made. There where change a cooling rates of proceses without delay after forging proces. One experiment was made for two temperature of forging.proces. Two series of mechanical tests was made and then was observed phenomenon of metalurgical structure changed and mechanical properties.

The work presented in this master thesis deal with the issue of quenching, investigation regarding different cooling rates and its effect on the material properties of aluminum alloy in the 6xxx series used for crash purposes in cars, such as crash boxes, beams and other crash relevant parts. Precipitation of Mg2Si due to different cooling rates affects the material properties such as crash performance, thus the aluminum alloy used is sensitive to different cooling rates. In order to perform tests with different cooling rates a cooling rig was constructed. In order to evaluate the different cooling rates both mechanical testing such as tensile test and 3-point bending test and compression test were performed. Also analyses with scanning electron microscope/energy-dispersive x-ray spectroscopy were performed to estimate grain boundary decoration of Mg2Si due to the different cooling rates. Furthermore LOM analyses were performed to evaluate if the experimental setup had any effect on material properties such as grain size. The constructed cooling rig produced different cooling rates with reliable repeatability as intended. Cooling rates between 130 ̊C/s and 20 ̊C/s were accomplished. Mg2Si occurred in all investigated test samples with various amounts. Higher cooling rates decreases the precipitation of Mg2Si to the grain boundaries, higher cooling rates also increased the bending angle achieved from the 3-point bending test. Furthermore, extensive solution heat treatment at elevated temperatures leads to grain growth.