One dimensional (1-D), zinc oxide (ZnO) and copper (II) oxide (CuO), nanostructures have great potential for applications in the fields of optoelectronic and sensor devices. Research on nanostructures is a fascinating field that has evolved during the last few years especially after the utilization of the hydrothermal growth method. Using this method variety of nanostructures can be grown from solutions, it is a cheap, easy, and environment friendly approach. These nanostructures can be synthesized on various conventional and nonconventional substrates such as silicon, plastic, fabrics and paper etc. The primary purpose of the work presented in this thesis is to realize controllable growth of ZnO, CuO and nanohybrid ZnO/CuO nanostructures and to process and develop white light emitting diodes and sensor devices from the corresponding nanostructures. The first part of the thesis deals with ZnO nanostructures grown under different hydrothermal conditions in order to gain a better understanding of the growth. Possible parameters affecting the growth such as the pH, the growth temperature, the growth time, and the precursors  concentration which can alter the morphology of the nanostructures were investigated (paper 1). Utilizing the advantage of the low temperature for growth we synthesized ZnO nanostructures on different substrates, specifically on flexible substrates, which are likely to be integrated with flexible organic substrates for future foldable and disposable electronics (paper 2, 3). In the second part of the thesis, using the results and findings from the growth of ZnO nanostructures, it was possible to successfully implement ZnO nanostructures for white light emitting diodes (LEDs) on different flexible substrates (paper 4, 5). In paper 4 we realized a ZnO/polymer LED grown on a paper substrate. In paper 5 we extended the idea to print the ZnO nanorods/polymer hybrid LEDs with potential application to large area flexible displays. In the last part of the thesis, CuO and nanohybrid ZnO/CuO nanostructures were utilized to fabricate Ag+ detection and humidity sensors. In paper 6 we reported Ag+ selective electrochemical sensor based on the use of functionalized CuO nanopetals. To combine the advantages of both oxides nanostructures and to improve the performance we fabricated a pn-heterojuction using intrinsic n-ZnO nanorods and p-CuO nanostructures which were then utilized as an efficient humidity sensor (paper 7).

Proteinogenic amino acids are the basic structural building units of proteins. Their analysis is important in many fields, especially in medicine. This thesis deals with one of the methods of derivatization of amino acids in order to increase their absorption in the UV - the post-column derivatization using copper (II) oxide. It is quick, robust and easy-to-use method. Following the nowadays trend in the analysis of free amino acids, this thesis is focused on the HILIC mode separation environment.

The basic necessities to sustain life are – air, water and food. Although the harmful effects due to contaminated food or water are dangerous to life, these can be reduced/avoided by controlling the intake. Whereas, in case of air, the same amount of control cannot be exercised as there is very little, one can do in case of inhalation. Maximum damage to life is due to air contamination which can be detected and prevented by using gas sensors. The proper use of these sensors not only save lives, but also minimizes social and financial loss. The objective of this thesis work is to study and explore the use of p-type semiconducting material such as CuO, as a promising gas sensing material for organic compounds (VOCs), compatible with existing silicon fabrication technology. The Thesis consist of 7 chapters: Chapter 1 covers the general introduction about gas sensors, sensor parameters, criteria for the selection of sensing material, suitability of CuO as sensing material and a brief literature survey. The second chapter includes the selection of substrate, cleaning procedures and suitable deposition method. The deposition method used in the present thesis work is DC/RF magnetron sputtering. The reactive magnetron sputtering is employed during the deposition of CuO sensing films. It also includes basic introduction about some of the common material characterization techniques. This is followed by Chapter 3 which includes the optimization of sputtering process parameters such as applied power, working pressure, Ar-O2 ratio and substrate temperature for CuO sensing film and the effect of these on surface morphology. Information on the optimized sputtering parameters for electrode film (silver and gold) deposition has also been included in this chapter. In order to study the sensing behavior of the sensor, suitable testing set-up is necessary. This leads us to Chapter 4 that discusses the development of an in-house built sensor testing setup and its automization using MATLAB. The automated testing set-up facilitates off-time data plotting as well as real-time data plotting during the sensing process. To demonstrate the working of the set-up, some initial results obtained are also included in this chapter. After ascertaining the functioning of the automated gas sensor testing set-up, detailed study on the sensing behavior of nanostructured CuO films was performed. This information along with the necessary details is included in Chapter 5. The sensing response of nanostructured CuO films has been studied for different VOCs such as alcohol, toluene and benzene. The study carried out on the effect of different surface additives like multi-walled carbon nanotubes (MWNTs), gold or platinum on ethanol sensing has also been included in this chapter. During the use of MWNTs as surface additives, different concentrations of MWNTs – 0.01 mg, 0.05 mg and 0.1 mg have been dispersed on the CuO sensing film. The sample with lowest concentration of MWNTs exhibited highest sensitivity and lower response time. It is due to the fact that, higher concentrations of MWNTs do not result into uniform dispersion over the CuO films and cover the sensing film almost completely. Operating temperature is the most important factor affecting the performance of a gas sensor. In order to maintain the operating temperature for the portable sensor, the sensor is usually integrated with a heater. The chapter 6 deals with heater optimization including design, simulation and fabrication. In this chapter, microheater as well as macro-heaters were simulated and fabricated. The fabricated macro-heater is bonded with the sensor by eutectic bonding. One of the bonded samples was studied for its sensing response. The final chapter of the thesis deals with the conclusion of present research work and the possible further work on CuO gas sensor.

Photoelectrodes and photovoltaic devices have been prepared via multiple thin film deposition methods. Aerosol assisted chemical vapour deposition (AACVD), electrodeposition (ED), chemical bath deposition (CBD) and doctor blade technique (DB) have been used to deposit binary and ternary metal oxide films on FTO glass substrates. The prepared thin films were characterised by a combination of SEM (Scanning Electron Microscopy), powder X-ray diffraction, mechanical strength tests and photochemical measurements. Nickel oxide (NiO) thin films prepared by AACVD were determined to have good mechanical strength . with a photocurrent of 7.6 μA cm-2 at 0 V and an onset potential of about 0.10 V. This contrasted with the dark current density of 0.3 μA cm-2 at 0 V. These NiO samples have very high porosity with crystalline columns evidenced by SEM. In comparison with the AACVD methodology, NiO films prepared using a combination of ED and DB show good mechanical strength but a higher photocurrent of 24 μA cm-2 at 0 V and an onset potential of about 0.10 V with a significantly greater dark current density of 7 μA cm-2 at 0 V. The characteristic features shown in the SEM are smaller pores compared to the AACVD method. Copper (II) oxide (CuO) and copper (I) oxide (Cu2O) films were fabricated by AACVD by varying the annealing temperature between 100-325°C in air using a fixed annealing time of 30 min. It was shown by photocurrent density (J-V) measurements that CuO produced at 325 °C was most stable and provided the highest photocurrent of 173 μA cm-2 at 0 V with an onset potential of about 0.23 V. The alignment of zinc oxide (ZnO) nano-rods and nano-tubes fabricated by CBD have been shown to be strongly affected by the seed layer on the FTO substrate. SEM images showed that AACVD provided the best seed layer for aligning the growth of the nano-rods perpendicular to the surface. Nano-rods were successfully altered into nano-tubes using a potassium chloride bath etching method. NiO prepared by both AACVD and the combined ED/DB method were sensitized to absorb more of the solar spectrum using AACVD to deposit CuO over the NiO. A large increase in the photocurrent was observed for the p-type photoelectrode. These p-type photoelectrode showed a photocurrent density of approximately 100 μA cm-2 at 0 V and an onset potential of 0.3 V. This photocathode was then used as a base to produce a solid state p-type solar cell. For the construction of the solid state solar cells several n-type semiconductors were used, these were ZnO, WO3 and BiVO4. WO3 and BiVO4 were successfully produced with BiVO4 proving to be the optimum choice. This cell was then studied more in depth and optimised by controlling the thickness of each layer and annealing temperatures. The best solid state solar cell produced had a Jsc of 0.541 μA cm-2 (541 nA) and a Voc of 0.14 V, TX146 made up of NiO 20 min, CuFe2O4 50 min, CuO 10 min, BiVO4 27 min, using AACVD and then annealed for 30 min at 600°C.