Tato diplomová práce obsahuje komplexní návrh systému aktivního řízení proudu instalovaného na osobním voze Škoda Roomster. Tato práce navazuje na výzkum provedený VUT a TUB na vozidle Volkswagen UP! Návrh lze rozdělit na tři základní části - návrh spoileru, návrh závěsů a návrh vyfukovacího systému. V každé z těchto částí je návrh detailně popsán a potřebná výkresová dokumentace je součástí práce v její příloze. Pro potřeby návrhu vyfukovacího systému bylo provedeno jeho testování. Výsledky testu jsou v této části uvedeny. Práce také obsahuje komplexní popis sestavení celého systému a jeho instalace na automobil.

Thesis deals with proposal lay – out assembly for pneumatic cylinder. Assembly is proposed into separate workplace. Single step are described in those work according to which workplace assembly are put together, division pneumatic cylinder to single constructional insider division and operation on single workplace and description these workplace. Analysis proposal is implementation in the end.

The diploma thesis ‚Rubber Torsional Vibration Damper Of a Four-Cylinder Diesel Engine‘ covers all the development phases related to a design of a rubber damper for a specified engine. The individual phases of it are discussed in details throughout the thesis. At first, the construction plan of a crankshaft is given. The computational checks for torsional vibrations and forced torsional vibration are performed then. With regards to it there might be derived the basic parameters and dimensions of a rubber torsional vibration damper. The knowledge of them enables to prepare the constructional plan of a rubber torsional vibration damper. By using this damper construction plan the torsional displacements (deviations) and forced vibrations are calculated. Finally, a mechanical and thermal stress test of this damper is performed and a crankshaft production drawing is produced.

The aim of this diploma is to design a crankshaft for a six-cylinder commercial vehicle, which is one of the unified motors. The main parts are the design of the crankshaft configuration, the crankshaft balancing method for forces and moments, the crankshaft design documentation, and the crankshaft strength verification. The design of torsional vibration damping characteristics is also made and its effect on torsional vibration and crankshaft strength is determined.

This diploma thesis, following the bachelor's thesis, is devoted to the gas-liquid unit of a vehicle, as the central element of hydropneumatic suspension. The aim is to dimension and construct this component and integrate it together with other elements into a complex suspension system. Based on possible forms listed in the research section, regarding to current development trends, the form of the unit is chosen. The practical part begins with simulations comparing a hydropneumatic with a conventional suspension system. After solving this issue, it is possible to proceed to the dimensioning of the basic parameters of the unit and then to its construction, respecting the relevant strength calculations. The last step is to build a conceptual design of the whole hydropneumatic suspension system.

This thesis deals with the R-material use in asphalt mixtures. In the theoretical part, different kinds of flexible pavement recycling and ways of adding R-material into asphalt mixtures are discussed. The practical part deals with asphalt layers design and manufacture, specifically for binder course ACL 16+. R-material content in the blends is 0%, 20%, 25% and 30%. EVOTHERM MA3 rejuvenator is used as additive for softening of R-material. Various mixtures are compared based on tests - resistance to permanent deformation, resistance to the effects of water and low temperature properties.

This Diploma thesis occupies with design of hydraulic puller. In work are mentioned possible types of construction. Choice construction of puller is disposed with parameters: maximum pushing force 50 kN, speed of piston rod 0,05 m/s. This work also contains FEM analysis by computer programme I-DEAS. The work also occupies with design of fluid drive.

The main aim of this master’s thesis is to design the drivetrain of four-cylinder gasoline internal combustion engine with torsional vibration rubber dumper. For the basic parameters of the engine are designed two optional crankshafts. Crankshaft with eight counterweights and crankshaft with four counterweights. The thesis also includes modal analysis of the crankshaft using FEM, and design of the main dimensions of the dumper. The following part describes the calculation of force torsional vibration and safety factor solution of crankshaft fatigue using FEM. The final calculation is of the temperature field in the rubber dumper in selected operating modes.

Tato diplomová práce uvádí dynamiku klikového mechanismu šestiválcového řadového motoru za účelem návrhu klikového hřídele v CAD programu Pro/Engineer. Následuje popis vibrací klikového mechanismu a analytický výpočet jeho torzních vibrací. Hlavní část diplomové práce se pak zabývá konverzí hřídele do konečno-prvkového modelu v programu ANSYS a jeho importem do prostředí Adams/Engine. V tom je provedena modální analýza klikového ústrojí pro získání vlastních frekvencí a tvarů. Na konec práce je porovnán výstup z analytického řešení a výsledky z multi-body systému.

This diploma thesis deals with the mechanical proposal of hydraulic puller. Furthermore, it includes the detail design solutions. The project also includes the calculation of the hydraulic puller parameters: maximum pushing force is 60 kN, speed of movement is 0.1 m s-1. This work also contains of stress analysis FEM with I-DEAS software. Following part deals with the design of hydraulic circuit for driving puller. At the end of work there are options for replacements of hydraulic puller by mechanical systems.