This master’s thesis deals with the design and fabrication of DC arc welder supplied from its own rechargeable battery. Battery cells’ type is LiFePO4 which can provide high currents even at relatively low capacity. The BMS circuits are designed within the battery. Major power part of the welder is a step-down converter with synchronously switching low transistors at the position of free-wheel diode. The converter operates at 100 kHz frequency. The current of the battery welder can be regulated in the range from 0 to 120 A.

The aim of this master thesis is to describe the requirements put on electronics and headlights within car industry, above all on the newly emerging 48V power network. In the thesis the principles of chosen DC/DC buck converter topologies are briefly described. In the next part of this thesis the converters are designed and manufactured. Further, the EMC chamber measurement of these converters and their subsequent evaluation is performed. In the last part the proposed converters are compared and evaluated.

This diploma thesis deals with design of DC/DC converter which will be used in one-phase inverter powered from batteries. Required parameters are output power of 100 W, input voltage of 24 V and output voltage of 350 V. In the first part is briefly discussed used topology of flyback converter. In the next part is designed impulse transformer with a request to design impulse transformer as small as possible. Thesis continues with draft of power components placed on primary and secondary side of converter. In this thesis is part about limitation of voltage overshoot at turn off transistor. Next part of this thesis deals with the design of control circuits using an integrated circuit from the UC384x family. Thesis continues with the production and debugging of the converter. At the end of this thesis are measurements confirming the correctness of the proposed design.

This thesis deals with the design of a DC/DC converter designed for charging supercapacitors from the 36 V voltage source and consequent back transformation of supercapacitors voltage to the required output voltage. In the thesis the designs of decreasing and increasing DC/DC converters including schematics and calculations of individual components are presented and described. The calculations necessary for the supercapacitors to meet the 10Wh energy condition and the voltage balancer on the capacitors are given below. Completely designed equipment will be assembled and tested on supercapacitors with lower energy.

This master´s thesis describes switch mode power supply and discusses the design of its individual parts. It also contains a simulation of the power part of the converter and a reseach in the area of DC/DC converters.

This thesis is about theory of switching power supplies and about a specific solution of switching power supply for electron microscope. In the beginning of the thesis are mentioned various solutions of part blocks of switching power supplies, their advanteges and disadvanteges, and their suitability for electron microscopy. In the next part of the thesis are described requirements and design scheme of switching power supply for scanning part of electron microscope. The thesis i also about technical solution and practical testing of the switching power supply and verification of its functions.

This thesis deals with design of evaluation platform for integrated circuit NCV78934, which is designed to control LED headlights in automotive industry. The theory concerning the current regulation of buck converter, schematic design, PCB design and software design are also included in the thesis. Finally the measured data and testing procedures of the designed evaluation platform are discussed.

Master’s thesis deals with design and realization of power supply, which is supplied and controlled via USB bus. In theoretical part there are described principles of USB communication drivers which ensures this communication, there are described principles of linear voltage regulators and basic types of DC/DC converters. Mentioned is also PID regulator theory. Practical part aims for design of suitable DC/DC converter topology and creating algorithms for driving this converter. Next there is created PC program which drives power supply and there are also accomplished basic power supply measurements. The result of this thesis is functional power supply supplemented with PCB.

This project proposal describes the involvement of a wireless pager. It describes the possibility of realization, block diagrams of the receiver and transmitter controlprogram for their individual and flowcharts. In the theoretical design are taken intoaccount the ease of use, durability and endurance of the battery function. Was chosenfor the realization of a suitable wireless module, with a sufficient range. The goal is todesign a suitable wireless pager with sufficient range, durability and reasonable price that could be used within a department or a house to call for help.

This master's thesis deals with a design and realization of a LED driver that is based on integrated circuits NCV78703 and NCV78723 from ON Semiconductor. The aim of the project is to create a demonstration application with these integrated circuits for the use of company. The circuits can be especially used for driving LED automotive lights. The driver is controlled with a microcontroller also providing a communication with a software running on a PC via USB interface. This software enables to simply modify parameters of the driver in order to adjust an intensity of LEDs.