Laboratory directed evolution have enabled the discovery of numerous functional natural and synthetic macromolecules with tailor-made functions. However, approaches that use enzymes to effect the crucial translation from an information carrier molecule such as DNA or RNA to synthetic polymers are limited to producing close analogs of nucleic acids, either due to a strict requirement to hybridize with a nucleic acid template or as a consequence of the limited substrate scope of polymerase enzymes. / Chemistry and Chemical Biology

Carbon nanotubes are appealing materials for nanofabrication due to their unique properties and structures. However, for carbon nanotubes to be used in mass-fabricated devices, precise control of nanotube orientation and location on surfaces is critical. I have developed a technique to align single-walled carbon nanotubes (SWNTs) on surfaces from a droplet of nanotube suspension under gas flow. Fluid motion studies indicate that alignment is likely due to circulation of SWNTs in the droplet. My work provides a facile method for generating oriented nanotubes for nanodevice applications. I have also devised an approach for localizing SWNTs onto 1-pyrenemethylamine-decorated DNA on surfaces. I found that 63% of SWNTs on surfaces were anchored along DNA, and these nanotubes covered ~5% of the total DNA length. This technique was an initial demonstration of DNA-templated SWNT localization. In an improved method to localize SWNTs on DNA templates, dodecyltrimethylammonium bromide was utilized to suspend SWNTs in aqueous media and localize them on DNA electrostatically. SWNT positioning was controlled by the surface DNA arrangement, and the extent of deposition was influenced by the SWNT concentration and number of treatments. Under optimized conditions, 83% of the length of surface DNAs was covered with SWNTs, and 76% of the deposited SWNTs were on DNA. In some regions, nearly continuous SWNT assemblies were formed. This approach should be useful for the fabrication of nanotube nanowires in nanoelectronic circuits. Using my improved procedures, I have localized SWNTs on DNA templates across electrodes and measured the electrical properties of DNA-templated SWNT assemblies. When a DNA-templated SWNT was deposited on top of and bridging electrodes, the measured conductance was comparable to literature values. In contrast, SWNTs with end-on contacts to the sides of electrodes had conductances hundreds of times lower than literature values, probably due to gaps between the SWNT ends and the electrodes. This work provides a novel approach for localizing SWNTs across contacts in a controlled manner. These results may be useful in the fabrication of nanoelectronic devices such as transistors with SWNTs as active components. Moreover, this approach could be valuable in arranging SWNTs as electrical interconnects for nanoelectronics applications.

In this dissertation, I developed a Pd seeding method in association with electroless plating, to successfully metallize both lambda DNA and DNA origami templates on different surfaces. On mica surfaces, this method offered a fast, simple process, and the ability to obtain a relatively high yield of metallized DNA nanostructures. When using lambda DNA as the templates, I studied the effect of Pd(II) activation time on the seed height and density, and an optimal activation time between 10 and 30 min was obtained. Based on the Pd seeds formed on DNA, as well as a Pd electroless plating solution, continuous Pd nanowires that had an average diameter of ~28 nm were formed with good selectivity on lambda DNA. The selected Pd activation time was also applied to metallize "T"-shape DNA origami, and Au coated branched nanostructures with a length between 200-250 nm, and wire diameters of ~40 nm were also fabricated. In addition, I found that the addition of Mg2+ ion into the reducing agent and electroless plating solution could benefit the surface retention of Pd seeded DNA and Au plated DNA structures. This work indicated that DNA molecules were promising templates to fabricate metal nanostructures; moreover, the formation of Au metallized branched nanostructures showed progress towards nanodevice fabrication using DNA origami. Silicon surfaces were also used as the substrates for DNA metallization. More complex circular circuit DNA origami templates were used. To obtain high enough seed density, multiple Pd seeding steps were applied which showed good selectivity and the seeded DNA origami remained on the surface after seeding steps. I used distribution analysis of seed height to study the effect of seeding steps on both average height and the uniformity of the Pd seeds. Four-repeated palladium seedings were confirmed to be optimal by the AFM images, seed height distribution analysis, and Au electroless plating results. Both Au and Cu metallized circular circuit design DNA origami were successfully obtained with high yield and good selectivity. The structures were maintained well after metallization, and the average diameters of Au and Cu samples were ~32 nm and 40 nm, respectively. Electrical conductivity measurements were done on these Au and Cu samples, both of which showed ohmic behavior. This is the first work to demonstrate the conductivity of Cu metallized DNA templates. In addition, the resistivities were calculated based on the measured resistance and the size of the metallized structures. My work shows promising progress with metallized DNA and DNA origami templates. The resulting metal nanostructures may find use as conducting interconnects for nanoscale objects as well as in surface enhanced Raman scattering analysis.

The past decade has witnessed a breakthrough in the field of structural DNA nanotechnology, which utilizes DNA molecules as a construction material rather than as simple carriers of the genetic information. With the superior programmability of DNA, sub-nanometer precision in the self-assembly of various complex two- and three-dimensional nanostructures is achievable. It also allows a site-specific placement of different objects and functional groups onto the formed structures. This has enabled the assembly of highly sophisticated nanostructures for various applications. While the field of structural DNA nanotechnology has been astonishingly advancing, many nanoelectronics-relevant structures are made of inorganic materials, and DNA-based nanostructures have shown rather low conductivity. This has limited the use of DNA structures in nanoelectronics and reflected the need for a similar programmable route for the inorganic nanofabrication. A conceivable solution would use DNA nanostructures in a way that will precisely transfer the structural information of the DNA shapes into fabricated metallic nanostructures. One way to do that is to use the DNA nanostructures as templates for external material deposition onto the DNA surface. While this strategy has been effective in proving the concept of DNA-shape transfer, metallic nanostructures fabricated this way have shown some drawbacks, such as showing rough surface morphologies and lacking the required homogeneity for the fabricated metallic structures. An alternative strategy would be to design DNA mold structures that can dictate the shape of metal that is “cast” inside such a DNA container. The main topic of my thesis concerns the second strategy. To discuss this in detail, the structure and some of the important properties of DNA are introduced in section 1.1. In section 1.2 the main milestones in the development of the DNA-nontechnology field are discussed and section 1.3 focuses on previous fabrication approaches of DNA-based metallic nanostructures.